Dynojet Power Commander 6 Yamaha FZ8 2011-2013 Installation Guide
- October 27, 2023
- Dynojet
Table of Contents
Power Commander 6 Yamaha FZ8 2011-2013
Installation Guide
POWER COMMANDER 6
Installation Guide for: PC6-22040
Model Coverage: 2011-2013 Yamaha FZ8/Fazer
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
3 VELCRO STRIPS
1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE
TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can
switch on the fl y between these two base maps when you hook up a switch to the
MAP inputs. You can use any open/close type switch. The polarity of the wires
is not important.
Shifter
(Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires
from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of
the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal side
of the sensor and run a wire into this input. This will allow you to calculate
gear position in the Control Center Software. Once gear position is setup you
can alter your map based on gear position and setup gear dependent kill times
when using a quick shifter.
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your fuel curve based on this input in the
Power Core software.
Launch You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged (continuity) will only allow the RPM
to be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLATION GUIDE
2 2011-2013 YAMAHA FZ8/FAZER
INSTALLING THE POWER COMMANDER 6
-
Remove the seat.
-
Remove the fuel tank cover. Prop the front of the fuel tank up.
-
Mount the PC6 in the tail section using the supplied Velcro.
Clean both surfaces with the supplied alcohol swab prior to attaching the Velcro.
-
Attach the ground wire from the PC6 to the negative side of the battery.
-
Unplug the 16-pin GREY connector under the fuel tank.
-
Unplug the 4-pin BLACK connector for the O2 sensor.
-
Plug the PC6 in-line of the stock wiring harness and throttle body connector.
-
Bolt the fuel tank back into place and reinstall cover.
Note: It is recommended to reset your throttle position in the Control
Center Software. Connect the USB cable to your computer and to the PC6.
Open the software and go to Power Commander Tools – Calibrate – Throttle
Position. Turn the ignition of the bike to the ON position and then click on
RESET in the software. Give the bike full throttle and then release. Click OK.
This will reset the TPS.
Download the latest map fi les from our web site at
dynojet.com/tunes.
2191 MENDENHALL DRIVE
NORTH LAS VEGAS, NV 89081
– 800-992-4993
– DYNOJET.COM
© 2011-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED 
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>