Dynojet Honda CB1000R 2018-2019 Power Commander 6 Installation Guide
- October 27, 2023
- Dynojet
Table of Contents
POWER COMMANDER 6
Install guide for: PC6-16078
Model coverage: 2018-2019 Honda CB1000R
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE 2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
IPC6-16078.01
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fly between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
Shifter
(Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires
from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of
the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this input. This will allow you to
calculate gear position in the Control Center Software. Once gear position is
setup you can alter your map based on gear position and setup gear dependent
kill times when using a quickshifter. .
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your fuel curve based on this input in the
Power Core software.
Launch
You can connect a wire to either Input 1 or Input 2 and then the other end
to a switch. This switch when engaged (continuity) will only allow the RPM to
be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the main seat and the passenger seat.
-
Remove the side panels over each side of the air box.
-
Remove the fuel tank.
-
Install the PC6 in the tail section.
Use the supplied Velcro to secure the unit in place. Make sure to clean both surfaces before attaching with the alcohol swab. -
Route the wiring harness down the left side of the frame.
-
Unplug the stock wiring harness from the Throttle Position Sensor. This connector is on the left side of the throttle body.
-
Unplug the wiring harness from each injector.
This image only shows the #1 & #2 injector. Make sure to unplug #3 & #4 on the other side of the frame. -
Plug the PC6 harness in-line of the stock wiring harness and TPS.
-
Plug the PC6 harness in-line of the stock wiring harness and fuel injectors.
ORANGE – cylinder #1 LEFT
YELLOW – cylinder #2
GREEN – cylinder #3
BLUE – cylinder #4 RIGHT -
Unplug the crank position sensor.
This is a RED, 2 pin connector located on the right side of the frame. -
Plug the PC6 in-line of the stock wiring harness and CPS.
-
Reinstall the fuel tank and bodywork.
Download the latest map files from our web site at dynojet.com/tunes.
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 – 800-992-4993 –
DYNOJET.COM
© 2018-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
Documents / Resources
|
Dynojet Honda CB1000R 2018-2019 Power Commander
6
[pdf] Installation Guide
Honda CB1000R, 2018-2019 Power Commander 6, Power Commander 6, 2018-2019 Honda
CB1000R, Honda CB1000R, CB1000R, Commander 6
---|---