Shinwa Industries 89072 Car Kit Bluetooth Module User Guide

Shinwa Industries 89072 Car Kit Bluetooth Module

Overview

BT-MC89-JK1 is a single-chip Bluetooth module based on CYW89072 of CYPRESS. The chip is a stand-alone baseband processor with an integrated 2.4GHz transceiver, It brings the latest mobile connectivity technology to automotive radio applications, Offering automotive Grade3 temperature performance, CYW89072 chip can met the AEC-Q100 certification.

Features

• Bluetooth 5.2
• Support class1 or class2 Bluetooth power level.
• Support high-speed UART communication
• Support standard HCI interface.
• Support PCM/I2S digital audio interface
• Surface mount type 23163.2mm
• Built-in pattern antenna on the module
• RoHS 2.0 compliant

Applications

• Automotive Hands-Free radios

Block Diagram

Module Specification

General Specification

Absolute maximum rating

Supply voltage

*Ripple voltage＜ 45mVp-p

| VDD| –| 3.6| V
VIO| –| 3.6| V
Minimum voltage on I/O pins| -0.3| –| V
Maximum voltage on I/O pins| | VIO+0.3| V

Recommended operating conditions

Supply voltage

*Ripple voltage＜ 45mVp-p

| VDD| 3.1| 3.3| 3.5| V
VIO| 3.1| 3.3| 3.5| V

Digital I/O characteristics

Characteristics| **Sym.| ****Min.| ****Max.| ****Unit**
---|---|---|---|---
Input low voltage(VIO=3.3V)| VIL| –| 0.8| V
Input high voltage(VIO=3.3V)| VIH| 2.0| –| V
Output low voltage| VOL| –| 0.4| V
Output high voltage| VOH| VIO-0.4| –| V
Input low current| IIL| –| 1.0| mA
Input high current| IIH| –| 1.0| mA
Output low current| IOL| –| 3.0| mA
Output high current| IOH| –| 3.0| mA

Power consumption

RF characteristics

Parameter| **Min.| ****Typ.**| |
---|---|---|---|---
 Transmitter
Output power| -6| 0| 4| dBm
Initial carrier-frequency tolerance| -75| –| +75| kHz
Modulation characteristics| Δf1avg| 140| –| 175| kHz
Δf2max| 115| | –| kHz
Δf2avg /Δf1avg| 0.8| –| –| –
Carrier frequency drift| 1slot| -25| –| +25| kHz
3slot / 5slot| -40| –| +40| kHz
Max. drift rate| -20| –| +20| kHz/50us
 Receiver
Single/Multiple sensitivity| P=-70dBm| –| –| <0.1| %
Maximum input level| P=-20dBm| –| —| <0.1| %

BLE

GFSK, 1Mbps

| ****

–

| ****

-90

| ****

–

| ****

dBm

Design Application

Pin Assignment

Pin Description

• All digital I/O has internal pull-up or pull-down values which are around 60Kohm.

If OTP is not used, pull this pin low.

7| RST_N| I| Active-low reset input.
8| VDD_3V3| I| Main power voltage source input
9| VIO_3V3| I| I/O voltage supply input
10| GND| GND| Ground connection
11| NC| –| NC
12| NC| –| NC
13| NC| –| NC
14| NC| –| NC
15| GND| GND| Ground connection
16| UART_CTS| I| UART clear to send input
17| UART_RTS| O| UART request to send output
18| UART_RXD| I| UART receive data
19| UART_TXD| O| UART transmit data
20| GND| GND| Ground connection
21| NC| –| NC
22| BT_DEV_WAKE| I/O| DEV_WAKE of general -purpose I/O signal
23| BT_HOST_WAKE| I/O| HOST_WAKE of general -purpose I/O signal
24| GND| GND| Ground connection

Dimensional Outline Drawing

Dimensional Package Drawing

Package Information

Tape Package

Reel Dimensions

Tape Dimensions

Packing Specification

Module shipments by vacuum packaging, packing diagram as follows:

Note: This product is applicable to moisture sensitivity level MSL3 (Based on JEDEC Standard J-STD-020)

FCC Statement

FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Integral antenna with antenna gain 0dBi

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, usesand can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more ofthe following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: ZWY89072 Or Contains FCC ID: ZWY89072”

When the module is installed inside another device, the user manual of the host must contain below warning statements;

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
2. This device may not cause harmful interference.
3. This device must accept any interference received, including interference that may cause undesired operation.
4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Any company of the host device which install this modular with modular approval should perform the test of radiated & conducted emission and spurious emission,etc. according to FCC part 15C : 15.247 and 15.209 &15.207 ,15B Class B requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209 &15.207 ,15B Class B requirement，then the host can be sold legally.

IC STATEMENT

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following  two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement

This modular complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the IC number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC:12033A-89072”

when the module is installed inside another device, the user manual of this device must contain below warning statements;

1. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
2. This device may not cause interference.
3. This device must accept any interference, including interference that may cause undesired operation of the device.

The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>