HOLMAN 2 Dial Tap Timer CO1601 User Guide
- June 6, 2024
- Holman
Table of Contents
2 Dial Tap Timer
www.holmanindustries.com.au User Guide
GLOSSARY
A. UNIVERSAL TAP ADAPTOR
B. TAP CONNECTION
C. UNION NUT
D. CONTROL DIALS
E. BATTERY COMPARTMENT
F. CLEAR SCREW-ON COVER
G. SNAP-ON HOSE CONNECTION
INSTALLATION
Make sure the washer is in place, then screw the 2 Dial Tap Timer to the tap. Turn it clockwise (hand tighten only).
There should be no need to use thread seal tape, as long as the tap seals onto the washer
BATTERY INSTALLATION
- Hold the Tap Timer with the battery compartment facing you
- Remove the BATTERY COMPARTMENT tray
- Connect a 9V alkaline battery to the battery connector
- Insert the connected battery and push in the BATTERY COMPARTMENT tray
When changing a battery, the Tap Timer will hold the current program if you fit the battery within 2 minutes. When changing the battery, make sure the battery compartment stays dry
Use only 9V alkaline batteries
SIMPLE 3 STEP PROGRAMMING
How to set run time and watering interval. Press ENTER to reference the start time.
The Tap Timer will not run immediately after program is set. Program will commence after chosen interval duration has lapsed
1. Turn the LEFT dial to select RUN TIME. Select from 2 minutes to 240 minutes
RUN TIME INTERVAL
ENTER
2. Turn the RIGHT dial to select the INTERVAL. Select from every 6 hours to every 7 days
RUN TIME INTERVAL
ENTER
3. Push ENTER the red LED will appear solid for three seconds to confirm your section. Watering will start at the selected interval
The time that the ENTER button is pushed is used as a reference start time. To change the program, simply follow the same three steps
RUN TIME INTERVAL
ENTER
MANUAL START
- Turn the LEFT dial to select RUN TIME
- Turn the RIGHT dial to MAN
- Press ENTER
Running a manual run time will not change any program previously entered. Watering will begin and end at selected run time. No need to move the dials
RUN TIME INTERVAL
ENTER
RUN TIME INTERVAL
ENTER
RUN TIME INTERVAL
ENTER
STOP OR NO WATERING
1. Turn the RUN TIME dial to the OFF position. While the RUN TIME dial is in the OFF position no watering will happen
To re-commence a pre-set program, move the RUN TIME dial to any other position
RUN TIME INTERVAL
ENTER
RED LED – OPERATING STATES
- SOLID for three seconds: Confirms program and each time the auto program is changed
- FLASHING every 30 seconds: All is running correctly
- FLASHING every one second: Battery needs changing
EXTRA WATERING CYCLES
The manual operation mention previously can be used for running an extra cycle
whilst the timer is programmed.
The manual cycle will run immediately after the ENTER button is pressed.
The Tap Timer will resume the automatic program once the manual time has
elapsed.
FAULT FINDING
- Ensure your tap is turned on
- Ensure your battery is in good condition. Use only 9V alkaline battery
When the Tap Timer is not using an automatic program, it must be in the OFF position. Turn the tap OFF when the Tap Timer is not in watering mode
CLEARING MEMORY
To clear an existing program, remove the battery and wait until the Tap
Timer resets. (This can take up to 5 minutes.)
Alternatively, remove the battery and initiate a manual start which will clear
the memory immediately.
TECHNICAL DATA
PRODUCT: Holman 2 Dial Tap Timer
PRODUCT CODE: CO1601
MAXIMUM WATER PRESSURE: 600 kPa
MINIMUM WATER PRESSURE: 100 kPa
BATTERY: Use a standard 9V alkaline battery
FLUID: Only use cold water with NO added chemicals
FREQUENCY OPTIONS: Every 6 hours, 12 hours, 24 hours, 48 hours, Every 3rd Day,
Every 4th Day, Every 4th Day, Every 7th Day
RUN TIME OPTIONS: 2, 5, 10, 15, 30, 60, 120 or 240 minutes.
We really appreciate having you as a customer, and would like to say thank you for choosing us. Should you have any questions about this product or its operation please call customer service on 1300 716 188
Head Office/Service
11 Walters Drive, Osborne Park WA 6017
Tel: +61 8 9416 9999 Fax: +61 8 9416 9920
support@holmanindustries.com.au
www.holmanindustries.com.au
Copyright © 2020 Holman Industries
Documents / Resources
|
HOLMAN 2 Dial Tap Timer
CO1601
[pdf] User Guide
HOLMAN, 2 Dial, Tap Timer, CO1601
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>