i safe M170A01 IS170.2 ATEX Ruggedized Mobile Phone User Manual

June 6, 2024
i-safe

i safe logo

i safe M170A01 IS170.2 ATEX Ruggedized Mobile Phone

Document No. 1045MM01REV00
Version: 2020-12-10
(c) 2020 i.safe MOBILE GmbH
i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda-Koenigshofen
Germany
Tel. +49 9343/60148-0
info@isafe-mobile.com
www.isafe-mobile.com

KEYS AND SPECIAL FEATURES

KEYS AND SPECIAL FEATURES

BUTTONS AND SPECIAL FEATURES
  1. EARPHONE JACK: To connect an earphone.
  2. TORCH: Use phone drop-down-menu to power ON/OFF the torch.
  3. CURRENT APPLICATION: Long press to show all opened apps.
  4. HOME BUTTON: To go back to the homescreen.
  5. BACK BUTTON: Back to previous screen mask.
  6. DELETE BUTTON: To delete characters entered incorrectly.
  7. POWER BUTTON: Prolonged pressing to switch the telephone on and off; press briefly to end a call.
  8. KEYPAD
  9. USB-PORT: For charging the device and to connect to other devices with the delivered USB cable.
  10. LOUDNESS CONTROL: Volume up/down.
  11. A NSWER BUTTON
  12. OPTIONAL BUTTON: Optional button used by different apps.
  13. SIDE BUTTON LEFT: Optional button used by different apps.
  14. NOTIFICATION LED: LEDs for charging and notification.
  15. CAMERA
  16. BATTERY COMPARTMENT
  17. BELT CLIP

INTRODUCTION

This document contains information and safety regulations which are to be observed without fail for safe operation of the device IS170.2 (Model M170A01) under the described conditions. Non-observance of this information and instructions can have serious consequences and / or may violate regulations.
Please read the manual and these safety instructions before using the device. In case of any doubt, the German version shall apply.
The current EU-declaration of conformity, Certificate of Conformity, safety instructions and manuals can be found at www.isafe-mobile.com or requested from i.safe MOBILE GmbH.

RESERVATION

The content of this document is presented as it currently exists. i.safe MOBILE GmbH does not provide any explicit or tacit guarantee for the accuracy or completeness of the content of this document, including, but not restricted to, the tacit guarantee of market suitability or fit-ness for a specific purpose unless applicable laws or court decisions make liability mandatory. i.safe MOBILE GmbH reserves the right to make changes to this document or to withdraw it any time without prior notice. Changes, errors and misprints may not be used as a basis for any claim for damages. All rights reserved.
i.safe MOBILE GmbH cannot be held responsible for any data or other loss and direct or indirect damages caused by any improper use of this device.

EX-SPECIFICATIONS

The device IS170.2 is suitable for use in potentially explosive atmospheres classified as zones 2/22 in accordance with directives 2014/34/EU and 2014/53/EU, as well as the IECEx scheme.

EX-MARKINGS

ATEX:
II 3G Ex ic IIC T4 Gc
II 3D Ex ic IIIB T135°C Dc
Certificate of Conformity:
EPS 20 ATEX 1 208 X
CE-designation

IECEx:
Ex ic IIC T4 Gc
Ex ic IIIB T135°C Dc
IECEx Certificate: IECEx EPS 20.0078X

Temperature range:
-20°C … +60°C (EN/IEC 60079-0)
-10°C … +50°C (EN/IEC 62368-1)

Manufactured by:
i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda-Koenigshofen
Germany

EU-DECLARATION OF CONFORMITY
The EU-declaration of conformity can be found at the end of this manual.

FAULTS AND DAMAGES

If there is any reason to suspect that the safety of the device has been compromised, it must be withdrawn from use and removed from any ex-hazardous areas immediately. Measures
must be taken to prevent any accidental restarting of the device. The safety of the device may be compromised, if, for example:

  • Malfunctions occur.
  • The housing of the device shows damage.
  • The device has been subjected to excessive loads.
  • The device has been stored improperly.
  • Markings or labels on the device are illegible.
  • We recommend that a device displaying errors or in which an error is suspected be sent back to i.safe MOBILE GmbH to be checked.

EX-RELEVANT SAFETY REGULATIONS

Use of this device assumes that the operator observes the conventional safety regulations and has read and understood manual, safety instructions and certificate.
The following safety regulations must also be complied with:

  • Inside ex-hazardous areas the covers of all interfaces must be closed. The battery has to be fixed securely.
  • To ensure the IP-protection, it has to be ensured that the all gaskets are present and functional.
  • There must be no large gap between the two halves of the housing and between the battery and housing.
  • The device may only be charged outside ex-hazardous areas.
  • The device may only be charged at temperatures between +5°C … +35°C.
  • Physical connections to other equipment are only allowed outside ex-hazardous areas.
  • The device may not be exposed to any aggressive acids or alkalis.
  • The device may only be used in zones 2 or 22.
  • Only accessories approved by i.safe MOBILE GmbH may be used.

FURTHER SAFETY ADVISES

  • Do not touch the screen of the device with sharp objects. Dust particles and nails may scratch the screen. Please maintain the screen clean. Remove dust on the screen with a soft cloth gently, and do not scratch the screen.
  • Do not put the device in environments with excessive temperatures, as this could lead to heating of the battery, resulting in fire or explosion.
  • Do not charge the device near any flammable or explosive substances.
  • Charge the device under indoor conditions only.
  • Do not charge the device in environments with much dust or humidity.
  • Do not use the device in areas where regulations or legislatives prohibit the use.
  • Do not expose the device or charger to strong magnetic fields, such as are emitted from induction ovens or microwaves.
  • Do not attempt to open or repair the device. Improper repair or opening can lead to the destruction of the device, fire or explosion. Only authorized personnel are allowed to repair the device.
  • Only use accessories approved by i.safe MOBILE GmbH.
  • Power off the device in hospitals or other places where the use of mobile phones is prohibited.
  • This device may affect proper work of medical equipment, such as pacemakers. Always keep a distance of at least 15 cm between the device and these devices.
  • To prevent possible hearing damages, do not listen at high volume level for long periods. Fully understand user manual before use. Ensure your device at low volume levels or power off before you leaving.
  • Observe all corresponding laws that are in force in the respective countries regarding the use of devices while operating a vehicle.
  • Please power off the device and disconnect the charging cable before cleaning the device.
  • Do not use any chemical cleaning agents to clean the device or the charger. Use a damp and anti-static soft cloth for cleaning.
  • The product shall only be connected to a USB interface of version USB2.0.
  • Do not discard old and abandoned lithium batteries into the trash, send them to designated waste disposal locations.
  • The user alone is responsible for any and all damages and liabilities caused by malware downloaded when using the network or other data-exchange functions of the device. i.safe MOBILE GmbH cannot be held responsible for any of those claims.

WARNING: i.safe MOBILE GmbH will not assume any liability for damages caused by disregarding any of these advices or by any inappropriate use of the device.

MAINTENANCE/REPAIR

Please note any legal requirements for periodic inspection.
The device itself has no user-serviceable parts. It is recommended to perform inspections according to the safety regulations and advises. If there is a problem with the device, please
contact your vendor or consult the service center. If your device is in need of repair, you can either contact the service center or your vendor.

BATTERY
The battery is not fully charged when the device is purchased, but it contains enough energy to power on the device. To obtain best battery performance and battery life, let the battery
discharge completely before charging it completely for the first three charging cycles.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose used batteries accordinmg to the instructions.

INSTALLATION OF THE MICRO SIM CARD
The device features a micro SIM card slot. This is located in the battery compartment under the battery.

WARNING: Do only change the SIM card when the device is switched off. Do not try to insert or remove the SIM cards when any external power supply is connected.

INSTALLATION OF THE microSD CARD
The device features a microSD card slot (up to 128 GB). This is located in the battery compartment below the battery.
If you want to remove the microSD card, please make sure that the card is not in use by the device. To remove the microSD card follow the instructions given in .

WARNING: Do only change the microSD card when the device is switched off. Do not try to insert or remove the microSD card when any external power supply is connected, otherwise the microSD card may be damaged.

RECYCLING
The crossed-out wheeled-bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies in the European Union. Do not dispose of these products as unsorted municipal waste. Always return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you help prevent uncontrolled waste disposal and promote the recycling of materials. More detailed information is available from the product retailer, local waste authorities, national producer responsibility organisations, or your local i.safe MOBILE GmbH representative.

INFORMATION CONCERNING SAR CERTIFICATION
(SPECIFIC ABSORBATION RATE)
Maximum SAR values for this model and the conditions under which these were determined:
SAR (head) 0.524 W/kg
SAR (body – worn) 1.405 W/kg
This device was tested for typical body-worn operations with the back of the handset kept
5 mm from the body.

TRADEMARKS
i.safe MOBILE and the i.safe MOBILE logo are registered trademarks of the i.safe MOBILE GmbH.
All other trademarks and copyrights are the properties of their respective owners.

CONTACT/SERVICE CENTER
FOR FURTHER QUESTIONS PLEASE CONTACT OUR SERVICE CENTER:
i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda-Koenigshofen
Germany
service@isafe-mobile.com
www.isafe-mobile.com/service

MAXIMUM OUTPUT POWER

Frequency bands   Maximum output power
GSM 900 2W
DCS1800 1W
WCDMA 900 24.0dBm
WCDMA 2100 24.0dBm
LTE Band 1 23.0dBm
LTE Band 3 23.0dBm
LTE Band 7 23.0dBm
LTE Band 8 23.0dBm
LTE Band 20 23.0dBm
LTE Band 28 23.0dBm
LTE Band 38 23.0dBm
LTE Band 40 23.0dBm
NFC -21.815dBu A/m at 10 m
WiFi 2.4G 17.91dBm EIRP
WiFi 5G 15.76dBm EIRP
BT 8.87dBm EIRP
BLE -0.96dBm EIRP
SRD 13.80dBm EIRP

GSM ,WCDMA,LTE, BT/BLE,2 4GWIFI/5GWIFI,NFC,GPS,SR.D can be used in Europe without restriction.

Restrictions in the 5 GHz band:
According to Article 10 (10) of Directive 2014/53/EU, the packaging shows that this radio equipment will be subject to some restrictions when placed on the market in Belgium (BE),Bulgaria (BG), the Czech Republic (CZ),Denmark (DK), Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain(ES), France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania(LT), Luxembourg (LU), Hungary (HU), Malta (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK),Finland (FI), Sweden (SE), the United Kingdom (UK), Turkey (TR), Norway(NO), Switzerland (CH), Iceland (IS), and Liechtenstein (LI).The WLAN function for this device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.

  AT BE BG CH CY CZ DE DK
EE EL ES FI FR HR HU IE
IS IT LI LT LU LV MT NL
PL PT RO SE SI SK TR UK

EU-DECLARATION OF CONFORMITY

EU – Declaration of Conformity
EU – Konformitätserklärung
according to directive 2014/34/EU, 2014/53/EU and 2011/65/EU (2015/863/EU) nach Richtlinie 2014/34/EU, 2014/53/EU und 2011/65/EU (2015/863/EU)
The company i.safe MOBILE GmbH declares under its sole responsibility that the product to which this declaration relates is in accordance with the provisions of the following data,
directives and standards:

Name & address of the manufacturer in the EU

Name & Anschrift des Herstellers innerhalb

der europäischen Gemeinschaft

| i.safe MOBILE GmbH i_Park Tauberfranken 10

97922 Lauda – Koenigshofen, Germany

---|---
Description of the device

Beschreibung des Geräts

| explosion protected mobile phone

explosionsgeschütztes  Mobiltelefon

type / Typ : IS170.2

Ex – marking

Ex – Kennzeichnung

| II 3G Ex ic IIC T4 Gc

II 3D Ex ic IIIB T135°C Dc

Conformity statement 2014/34/EU issued by

Konformitätsaussage 2014/34/EU ausgestellt durch

| EPS 20 ATEX 1 208 X

__

Bureau Veritas E&E Product Services GmbH Businesspark A96

86842 Tuerkheim, Germany

identification number / Kenn-Nummer : 2004

Applied harmonized standards

Angewandte harmonisierte Standards

| EN IEC 60079-0:2018; EN 60079-11:2012
Conformity statement 2014/53/EU issued| Shenzhen HUAK Testing Technology Co., Ltd.
by| 1F, B2 Building, Junfeng Zhongcheng Zhizao
Konformitätsaussage 2014/53/EU| Innovation Park, Heping Community, Fuhai
ausgestellt durch| Street,
 | Bao´an District, Shenzhen, China
Applied harmonized standards| EN 301 908-1 V11.1.7 (2018-12); EN 301 908-2
Angewandte harmonisierte Standards| V11.1.2; EN 301 908-13 V11.1.2 (2017-07); EN
 | 301 511 V12.5.1 (2017-03); EN 303 413 V1.1.1
 | (2017-06); EN 300 328 V2.1.1 (2019-04); EN
 | 55032:2015; EN 55035:2017; EN 61000-3-
 | 2:2014; EN 61000-3-3:2013+A1:2019; EN 301
 | 489-1 V2.2.1 (2019-03); EN 301 489-17 V3.2.0
 | (2017-03); EN 301 489-19 V2.1.1 (2019-04); EN
 | 62479:2010; EN60950-1:20066+A11:2009+
 | A1:2010+A12:2011+A2:2013
---|---
Conformity statement 2015/863/EU| SGS-CSTC Standards Technical Services Co., Ltd.
amending 2011/65/EU issued by| Guangzhou Branch
Konformitätsaussage 2015/65/EU ergänzt| 198 Kezhu Road, Scientech Park Guangzhou
2011/65/EU ausgestellt durch| Economic & Technology Development District,
 | Guangzhou, China 510663
Applied harmonized standards| IEC 62321-2:2013; IEC 62321-1:2013; IEC62321-
Angewandte harmonisierte Standards| 3-1:2013; IEC 62321-5:2013; IEC 62321-
 | 4:2013+A1:2017; IEC 62321-7-1:2015; IEC
 | 62321-7-2:2017 & ISO 17075-1:2017; IEC
 | 62321-6:2015; IEC 62321-8:2017
CE Marking

CE-Kennzeichnung

|

WWW.ISAFE-MOBILE.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

i-safe User Manuals

Related Manuals