Wellue BP2A Automatic Upper Arm Blood Pressure Monitor User Guide

Wellue BP2A Automatic Upper Arm Blood Pressure Monitor

Introduction

Thank you for purchasing the BP2/BP2A blood pressure monitor. For more details about the product, please refer the device user manual.

Product Features

Model| Blood Pressure Measurement| ECG

Measurement

---|---|---
BP2| √| √
BP2A| √|

Unpacking

• Main Unit;
• Charging Cable;
• User Manual;
• Quick Guide.

Overview

Main Unit

1. Start/Stop button
   • Power On/Off
   • Press to Start/Stop blood pressure measurement.
2. Function button
   • Press to Start ECG measurement.
   • Press and hold 2 seconds to review historical data.
3. Display screen
4. LED indicator
   • Blue light is on: the battery is charging.
   • Blue light is off: the battery is full charged.
5. ECG electrode
   Press and hold them during the ECG measurement.
   Cable connector
   Connect with the charging cable.

Display Screen

Blood Pressure Measurement

1. Systolic blood pressure
2. Diastolic blood pressure
3. Pulse display

ECG Recording

1. Real time ECG waveform
2. Recording progress bar
3. Real-time Heart Rate
4. ECG result
5. Heart Rate result

The screen items are described as below:

heart or other conditions.

Using the Monitor

Charging
Use the USB cable to charge the device. Connect the USB cable to a USB charger or to the PC. A fully charge will need 2 hours.
Note : The device cannot be used during charging.

Blood Pressure Measurement

Before Taking a Measurement
To help ensure an accurate measurement, follow these directions:

• Rest for at least 5 minutes before taking the measurement.
• Remove tight-fitting clothing from your arm.
• Try to measure your blood pressure at the same time each day for consistency.

Applying the Arm Cuff
Remove tight-fitting clothing from your left upper arm. Do not place the arm cuff over thick clothes. Wrap the cuff around the upper arm, about 1 to 2 cm above the inside of the elbow, as shown.
Note : Keep the monitor wearing position aligned with the middle finger.

How to Sit Correctly
Place your arm on a table so the cuff is level with your heart.

Measuring Blood Pressure

1. Power on the blood pressure monitor.
2. Press Start/Stop button to start blood pressure measurement.
3. The monitor will automatically deflate the cuff slowly during measurement.
4. The readings will be displayed when the measurement finished.
   Note : During measurement, you should keep still and do not squeeze the cuff.

After Measurement

1. The monitor will automatically release the cuff gas.
2. Remove the cuff.
   Note : The monitor will automatically shut down after no operation for 2 minute.

Recording ECG
Before Taking a Measurement

To help ensure an accurate measurement, follow these directions:

• The ECG electrode must be positioned directly against the skin.
• If your skin or hands are dry, moisten them using a damp cloth before taking the measurement.
• Stay still during the measurement, do not speak and hold the device still. Movements of any kind will falsify the measurements.

Recording ECG
There are four methods for recording ECG by cablefree operation.

C. Right hand to abdomen               D.Right hand to chest

To start an ECG Recording:

1. Put your right palm on the right side electrodes of the Monitor.
2. Put the left side electrodes to the body position that you desired to measure.
3. Once the body parts are placed on the electrodes, press Function button to start the EKG recording.
4. The readings will come after 30 seconds. To start recording ECG again, press Start/Stop button to return Home screen, then press Function button.
   Note : You can get different signal amplitude from the different methods. Use Lead II mode if signal is too low in Lead I mode.

Turn on/off Heartbeat Sound

The buzzer beep when heartbeat is detected during ECG recording. You can turn on/off the heartbeat sound on the App.

Review History Record

Hold Function button 2 seconds to enter History screen. The last measurement result will be displayed in default.

For ECG recording, the Heart Rate will be displayed first and then replayed the 30-second ECG waveform.

Using the APP

Download the App

App name: ViHealth
iOS : App Store
Android : Google Play

Install the App
Install the ViHealth app on your smart device.

Connect the monitor

1. Enable Bluetooth on your smart device settings.
2. Power on the monitor and run the ViHealth app.
3. Refer the guide on ViHealth App to complete the connection.
Note : DO NOT PAIR in the settings of your smart device.

Specifications

Physical

• Size (main unit) 135(L)×45(W) ×20(H) mm
• Weight (main unit) 240g
• Cuff size 22 – 42cm
• Wireless connectivity Bluetooth 4.0 BLE

Power

• Charge input DC5V
• Battery run time 500 measurements
• Battery charge time 2 hours

Blood Pressure Measurement

• Pressure range 0 – 300mmHg
• Pulse rate range 40 – 200 /min

ECG Recording

• Lead set Lead I, lead II, Chest Lead
• ECG length 30s
• Heart rate range 30 – 250/min

Storage

• Blood pressure records 50
• ECG records 10

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>