STETSOM EX8000EQ Amplifier Automotive User Manual

EXPORT LINE
EX8000EQ
Amplifier Automotive
User Manual

Features

The EX8000EQ offers 1 channel with advanced individual equalization features for Bass, Mid Bass, and Mid High, plus the traditional Level, High Pass, and Low Pass features. Its  Full Range frequency response from 10Hz to 15KHz allows the installation of Subwoofers, Woofers, Drivers, and Twitters.
Before Installing
Read this manual carefully before installing the amplifier. You must follow the instructions for the product’s installation and connections to guarantee optimal performance. If you have any questions, get in touch with us. Before using the amplifier, always follow these guidelines:

• Make sure the appliance is switched off before adding or removing any connections. This prevents possible damage to the equipment connected to the amplifier;
• Keep all cables as far away as possible from the ignition cables, electronic injection modules, and starter switch since they may cause noise interference;
•  Always use good quality cables and connectors. This guarantees the sound’s quality and fidelity;
• To avoid damaging the cables, make sure that they do not touch sharp metal edges.
  Important: Use a 350A fuse 30 centimeters from the battery as a safety precaution.

General Description

Inputs, Outputs, and Audio Controls

Power and Vents VENTS: This allows for the removal of warm air from the amplifier.
INPUT (RCA INPUT ): This input should receive the signal through an RCA cable connected to the output of the CD/ MP3 player.
LEVEL (LEVEL CONTROL) : Controls the input signal level, allowing for proper control of any CD/MP3 player currently on the market. It can be regulated as the  following:
a) on the CD/MP3 player, play any musical signal up to 80% volume.
(Ex: If the maximum volume on the player is 45 [100%], adjust to 36 [80%]).
b) on the amplifier, beginning at the lowest LEVEL, gradually increase until the clipping LED begins to flash.
c) slowly decrease the LEVEL until the LED goes off. (see entry 9 “OVER CLIP”)

General Description

HIGH PASS FILTER: Allows cut off of low frequency (subsonic) signals. This filter is very useful for woofer-type speakers.
In these cases, the woofers are not capable of reproducing subsonic frequencies, and these subsonic frequencies may even cause damage depending on the volume and the music played. It is regulated from 10Hz to 700Hz).
LOW PASS FILTER : This control varies the cut-off frequency from 50Hz to 15KHz.This filter allows passing only sounds beneath the cut frequency.
BASS : This control provides gain/attenuation of ±10dB in low frequency. The central frequency is 45Hz.
MID-BASS : This control provides gain/attenuation of ± 10dB in mid-low frequency. The central frequency is 270Hz.
MID-HIGH: This control provides gain/attenuation of ±10dB in mid-high frequency. The central frequency is 2KHz.
OVER CLIP (ON/OFF) : With this key turned on, the clipping LED will light up at 15% more final capacity.
SPEAKER OUTPUT : This output is MONO. Be careful of maintaining the correct polarity of the connections between the speakers and check the minimum impedance of this output. Use cables with a minimum gauge of 8 AWG.
COOLER: This fan will work when the device is triggered. They provide the device cooling.
REM (REMOTE CONTROL) : Connect the REM terminal to the electric antenna output of the CD/MP3 player. This will cause the amplifier to turn on automatically when you turn on your CD/MP3 player. A cable with a gauge of 20 AWG is adequate.
POSITIVE POWER SUPPLY : Connect the terminal **(+BAT) to the positive terminal of the battery (+12V) with a minimum gauge of 00 AWG. It is extremely important that a protective fuse or circuit breaker be used on this cable at a distance of 30 cm from the battery. The fuse or circuit breaker should be, at minimum, equal to the max current consumption value caused by playing musical signals (see technical specifications table).
GROUND CONNECTION : Use a cable with a gauge of at least 00 AWG. Connect the cable to the chassis of the vehicle.  (Note: always connect the GND wire of the CD  player—or other equipment—to the same ground point.)
POWER LED (BLUE): This indicator LED will light up when it is activated by the remote control signal from the CD/MP3 player.
PROT LED (RED) : This LED will light up for the following reasons (see the diagnostic table on the back cover):
a) Short circuit in the speakers
c) Low battery voltage
b) Excessive temperature
d) High battery voltage
CLIP LED (RED):** This LED will light up when the signal begins to suffer distortion.

Installing the Input Cables

ATTENTION : The use of a fuse or breaker is required since this amplifier has no internal fuses.

In order to install the power supply, use cables with a gauge of 00 AWG. The positive cable should come straight from the battery and have a fuse or protective breaker 30cm from the battery. The negative cable should have the same gauge as the positive cable and be screwed to the chassis of the vehicle, being careful to avoid paint and rust. These may interfere with the flow of the electrical current and cause loss of power and interference in the sound.

Installation of the Speaker Outputs

The speaker cables should be polarized (marked) so that you can easily identify which is positive and which is negative.
The minimum gauge is 8 AWG. Keep the cables well insulated and avoid metal parts as these may damage the insulation.

• WITH 2 SPEAKERS
EX8000EQ (1 OHM) : 2 x 2 OHMS
EX8000EQ (2 OHMS) : 2 x 4 OHMS

• WITH 4 SPEAKERS
EX8000EQ (1 OHM): 4 x 4 OHMS
EX8000EQ (2 OHMS): 4 x 8 OHMS

Troubleshooting

NO POWER
• The power cables are not connected correctly (terminals +BAT, GND, and REM). Verify that all the connections have electrical and mechanical contact.
• The fuse/circuit breakers are defective or blown. Replace them, making sure that the replacements are the correct ones!
NO SOUND
• The speaker cables or RCA plugs are not connected correctly.
• Verify that the LEVEL control is at the lowest setting. Check the amplifier filter controls.
NO SOUND. RED ALERT PROT BLINKING:
• See diagnostic guide
• The speakers or cables are defective, so check speakers, cables, and connections.
POOR SOUND QUALITY (DISTORTIONS):
• The speakers are overloaded. Decrease and readjust the volume level (see entry, “ LEVEL (LEVEL CONTROL)”)
WEAK BASS:
• Speaker cables (+) and (-) are switched or the speaker is out of phase (see entry “ INSTALLATION OF THE SPEAKER OUTPUTS”). Also, check BASS control adjustment.
ENGINE, HORN, TURN SIGNAL, INTERFERENCE:
• Use suppressing/insulated cables on the spark plugs.
• Use capacitors on the alternator, horn, and ignition.
• Run the shielded input cable away from any other cables, as they are particularly prone to interference.
• Install a separate power source (+12V) for the sound system. Use a fuse/circuit breaker 30 centimeters from the battery as the best precaution.
• Ground the amplifier properly. Remove paint from the chassis at the selected point, and connect the wire using a grounded terminal. In order to prevent rust, insulate it with paint.
Do not loop the ground. Avoid using multiple grounds. If possible, use a star connection, in which all the grounds run from a single point.

Diagnost Guide

In the eventuality of any problems, the amplifier will power down and the RED LED (PROT) light will begin to blink.
Depending on the problem, the RED LED (PROT) light will flash a certain number of times. The following table summarizes the diagnostics:

properly isolated.
Verify minimum impedance.
| Overheating.| Make sure the equipment is installed in a well-ventilated location.
| Low battery.| When used for long periods, the battery will run down. Recharge the battery.
| Battery overload or voltage greater than allowed.| Have the battery and/or alternator checked by a professional.

NOTE : In the event that the RED LED (PROT) light is flashing continuously, unplug the speakers and turn the equipment back on. If the problem persists, contact  STETSOM tech support.

Technical Specifications

Channels:| EX8000EQ 1 OHM 1| EX8000EQ 2 OHMS                                                   1
---|---|---
Power @ 14.4V – 1 Ohm (RMS):| 8000W| —
Power @ 14.4V – 2 Ohms (RMS):| 4500W| 8000W
Power @ 14.4V – 4 Ohms (RMS):| 2500W| 5100W
Min. Output Impedance:| 1 Ohm| 2 Ohms
Input Impedance:| 25K Ohms| 26K Ohms
Input Sensitivity:| 0.2V| 0.2V
T.H.D:| < 10% THD| < 10% THD
Signal to Noise Ratio:| >90dB| >90dB
Freq. Resp. @ 8 Ohms (-3dB):| 10Hz ~ 15KHz| 10Hz ~ 15KHz
Crossover Low Pass:| 50Hz ~ 15KHz| 50Hz ~ 15KHz
Crossover High Pass:| 10Hz ~ 700Hz| 10Hz ~ 700Hz
EQ – BASS @ 45Hz:| ±10dB| ±10dB
EQ – MID BASS @ 270 Hz:| ±10dB| ±10dB
EQ – MID HIGH @ 2KHz:| ±10dB| ±10dB
Over Clip (Power):| +15%| +15%
Power Supply:| 9.5 ~ 15Vdc| 9.5 ~ 15Vdc
Consumption Music:| 5.3 ~ 396 A| 5.2 ~ 396 A
Consumption BASS:| 5.3 ~ 750 A| 5.2 ~ 790 A
Dimensions (H x W x L):| 77 x 294 x 445 mm| 77 x 294 x 445 mm
Weight:| 6.3 Kg| 6.3 Kg

The measured data are based on equipment from the STETSON laboratory. Frequency reference of 1Khz with THD at ≤10% in impedances referring to the indicated in each aparição. The electronic components and the manufacturing process can present manufacturing variations, thus leading to a variation in the measurements made.

Any updates made in this manual will be available for consumers to consult without any charge on the brand’s site.
It is recommended that the updated manual be consulted whenever necessary.

EU Declaration of Conformity (DoC):
EX8000EQ – 1 OHM: www.stetsom.com.br/certifications/EX8000EQ_1–EUDoC2014-30-EU.pdf
EX8000EQ – 2 OHMS: www.stetsom.com.br/certifications/EX8000EQ_2–EUDoC2014-30-EU.pdf

/STETSOMBRASIL
/GRUPOSTETSOM
/STETSOMBRASIL
Rua Mariano Arenales Benito, 645-1 – Distrito Industrial –

MODEL: EX8000EQ (1Ω)
Voltage Supply: 9.5-15V DC
Current Range: 3.8-590A DC
MADE IN BRAZIL
MODEL: EX8000EQ (2Ω)
Voltage Supply: 9.5-15V DC
Current Range: 3.3-580A DC
MADE IN BRAZIL
Do not use normal trash for this product in case of damage or end of life

Warranty Information
Serie:
Date of Purchase: Month/Year manufacturing:
Dealer/Stamp:

STETSOM INDUSTRIA ELETRÔNICA LTDA. – CNPJ: 61.974.911/0001-04 RUA MARIANO ARENALES BENITO, 645 – DISTRITO INDUSTRIAL – CEP 19043- 130PRESIDENTE PRUDENTE – SP

Documents / Resources

| STETSOM EX8000EQ Amplifier Automotive [pdf] User Manual
EX8000EQ, Amplifier Automotive
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>