STETSOM 2000 Bravo Full Range Mono Digital Car Amplifier User Manual

: June 5, 2024
: STETSOM

Table of Contents

Introduction
Before installing
Input, output and audio controls
Indicators LED
Smart protection system
Instalation
Ferrite instalation
Troubleshooting
Technical specifications
Warranty Term
EU Declaration of conformity (DoC) **
Guarantee certificate
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRAVO FULL
MODEL: 2000
DIGITAL AMPLIFIER
USER MANUAL

Introduction

Thank you so much for choosing a Stetsom product! This amplifier was developed with cutting-edge technology for those who want high-quality sound from audio systems with one or more speakers or even an audio wall system.

Before installing

Please read this manual carefully.

All connections must be made with the product turned OFF.
A fuse must be installed between the amplifier and the battery is required to protect against overcurrent. The fuse needs to be installed as close to the battery as possible. Choose an appropriate fuse for the amplifier based on its consumption.
Use the wire recommended in this manual to keep cables from overheating cables and to obtain maximum power.
Keep the cables as short as possible to increase sound fidelity and avoid potential power losses.
Route the installation cables as far away as possible from the original vehicle wiring to prevent interference and noise in your audio system.
Perform the installation on a firm surface in a ventilated and dry place.
Installation should only be done by a qualified professional.

If you have questions , contact the store where the purchase or installation was done. For more information please contact our
Customer Service: BR +55 18 2104-9412.

Input, output and audio controls

RCA JACK INPUT: Input of the signal to be amplified. Connect to the radio/ player using high quality shielded RCA cables to prevent unwanted noise.
LEVEL: Level control for the signal at the amplifier’s input.
CROSSOVER:
• HIGH PASS FILTER (H.P.F.): This variable control allows you to select the initial frequency from 10Hz ~ 90Hz that will be reproduced by the amplifier.
• LOW PASS FILTER (L.P.F.): This variable control allows you to select the final frequency from 90Hz ~ 22KHz that will be reproduced by the amplifier.
BASS BOOST:
• BASS: Variable control for bass boost from 0dB ~ +10dB. FREQ: Variable control for BASS boost frequency from 30Hz ~ 70Hz.
FLAT KEY: This switch allows you to turn the FLAT mode on or off. Settings made on the CROSSOVER and BOOST controls will be turned off when using this mode.
OUTPUT CONNECTOR (SPEAKERS): MONO output of amplified signal for speakers connection. Check the minimum impedance and polarities before performing the installation.
Power input
COOLERs: It cools the amplifier. Install in a cool place being careful to not obstruct the air vents.
POSITIVE POWER SUPPLY CONNECTOR: Connect to the positive battery terminal of the battery using a minimum 4 AWG cable with a fuse/circuit breaker installed as close to the battery as possible.
REMOTE CONNECTOR (REM): Allows automatic activation of the amplifier when turning on the radio/player. Connect to the remote output of the radio/player using a cable a minimum of 18 AWG.
NEGATIVE POWER SUPPLY CONNECTOR : Connect to the negative terminal of the battery using a cable with a minimum of 4 AWG.

Indicators LED

| POWER (blue LED): Indicates amplifier operation when it is on.
PROT (top red LED): Indicates that the amplifier encountered malfunctions and entered protection mode, forcing it to shut down. Verify in the protection table below the possible problem and turn on the amplifier again. CLIP (lower red LED): Indicates signal distortion at the amplifier output.
---|---

Smart protection system

When the protection system detects a failure, the amplifier will turn off and the PROT LED will blink. For each type of failure, the LED will flash a certain number of times indicating the cause, as shown in the table below:

| Diagnostic: Short circuit or output overload.
Solution: Check that the speaker cables are well insulated and that the output impedance does not exceed that supported by the amplifier.
---|---
| Diagnostic: Excessive temperature. When the amplifier reaches approximately 194°F, audio is stopped and the coolers run at maximum speed to speed up the cooling process of the internal components.
Solution: Check if the amplifier is in a ventilated place or if the coolers are not obstructed. Keep the amplifier turned on for a few minutes for the coolers to assist in the cooling process.
| Diagnostic: Supply voltage less than 9V.
Solution: Check voltage of battery or power supply.
| Diagnostic: Supply voltage greater than 16V.
Sblinkolution: Check voltage of battery or power supply.

Instalation

Specification of the cables for proper installation:

Power connectors (positive/negative) …………………………………. 4 AWG
Remote connector ……………………………………………………………. 18 AWG
Output signal connectors (speakers) …………………………………… 9 AWG
Fuses or circuit breakers …………………………………………………….. 120A

The use of a fuse or circuit breaker is mandatory to protect the system from short circuits and overload. Install them as close to the battery as possible.

Installation should only be done by qualified professionals with the product turned OFF.

Ferrite instalation

It is recommended to attach the ferrite (already included in the package) to the cable that will be connected to the audio output.

Because it is a sensitive filter, attach the ferrite so that it is secure and protected from possible impacts.

Troubleshooting

AMPLIFIER DOES NOT TURN ON:

Verify that the cables are connected correctly. Make sure all connections have electrical and mechanical contact.
Fuses or circuit breakers may be defective or blown. Check the condition of the circuit breakers and make sure they are compatible with the equipment consumption.
Make sure that the battery is charged sufficiently for the product to operate.

NO SOUND:

The cables to the speakers or RCA plugs may not be connected incorrectly or defective.
Make sure that the LEVEL control is not at a minimum.

PROT LED FLASHING:

Make sure that the product’s air vents are not blocked and that the product is not overheating.
Speakers or cables are shorted. Check speakers, cables, and connections.

SOUND DISTORTIONS:

The speakers may be overloaded or defective, lower the level and then readjust the level. This setting can be adjusted as follows:
a) On the radio/player, play any musical signal and set the volume to 80% of the maximum (if the maximum volume of the radio /player is 45 (100%), set to 36 (80%).
b) On the amplifier, begin with the LEVEL control at minimum, increase gradually until the LED CLIP starts to flash. Slowly decrease the LEVEL until the led goes out completely.

WEAK OF BASS:

Cables of the speakers may be reversed and (speakers out-of-phase).

NOISE AND FAILURE IN SOUND:

Make sure that the installation is not close to the vehicle’s original wiring as it may cause interference and noise in the audio signal.
Create a separate power connection for the sound system. Use a fuse/ circuit breaker as close to the battery as possible for protection. Make a good grounding for the amplifier. To do this, remove the paint from the vehicle chassis at the desired point. Attach the wire using a ground terminal. To prevent oxidation, isolate with paint.
Do not loop the ground. Avoid using multiple grounds. If possible, use a star connection, so all the grounds run from a single point.

**** The data measured are based on STETSOM laboratory equipment. Test reference in frequency from 60hz to 1Khz with THD + N at 1% in impedances as indicated in each measurement. The electronic components and the manufacturing process may present manufacturing variations, thus leading to a variation in the measurements made.

Any updates made in this manual will be available for customers to consult free of charge on the brand’s site. It is recommended that the updated manual be consulted whenever needed.

Images contained in this manual are merely illustrative and may differ from the actual product.

Technical specifications

BRAVO FULL 2000

Minimum output impedance:	1 OHM	2 OHMs
Number of channels:	1
Power output @ 14.4V:	2600W RMS @ 1 Ohms
1720W RMS @ 2 Ohms	2750W RMS @ 2 Ohms

Warranty Term

STETSOM, through its network of Authorized Technical Assistance Providers, guarantees technical assistance to the purchaser of their products. The repairs of any defects duly established as being of the manufacturer will be done without cost for replacement components or parts and repair labor. The repairs will be done by the Authorized Technical Assistance Provider specially designated by STETSOM.

CONSULT THE LIST OF AUTHORIZED TECHNICAL ASSISTANCE PROVIDERS ON OUR WEBSITE: www.stetsom.com.br/en/assistencias-tecnica
If you do not locate technical assistance in your city, please contact us at: BR +55 18 2104-9412

WARRANTY CONDITIONS:
Our warranty is 1 (one) year against manufacturing defects. Its validity starts on the date of the Sale to the FINAL Consumer. To claim the benefits of this warranty, you must present one of the following documents: the Final Consumer’s SALE NOTE or this completed CERTIFICATE.

SITUATIONS THAT VOID THE WARRANTY:

1 year after the issuance of the invoice of sale to the consumer or 1 year after the certificate of warranty is filled out (dated and stamped by the retailer or installer) or 1 year from date of manufacture.
Violation of seals, alteration or removal of the product’s serial or lot number.
If the product suffers misuse or careless accidents involving: Water, Fire or Fall, or is installed in conditions contrary to the guidelines contained in the installation manual that accompanies the product.
Damages and changes in the circuit or adaptation of non-original parts.
If you use installation techniques contrary to those given in the manual.

QUESTIONS AND ADVICE:
STETSOM offers Customer Services to answer questions and give advice about their products and services. Please contact us through the channels: Phone: BR +55 18 2104-9412 — E-mail: suporte@stetsom.com.br Site: www.stetsom.com

EU Declaration of conformity (DoC) **

**

1 OHM| MODEL: BRAVO FULL 2000 (1Ω)
Voltage Supply: 9V – 16V DC
Current Range: 1.5A – 217A
MADE IN BRAZIL| www.stetsom.com.br/certifications/bravo-full_2000_1ohm_eu- doc.pdf
---|---|---
2 OHMS| MODEL: BRAVO FULL 2000 (2Ω)
Voltage Supply: 9V – 16V DC
Current Range: 1.4A – 217A
MADE IN BRAZIL| www.stetsom.com.br/certifications/bravo-full_2000_2ohms_eu- doc.pdf

Do not use normal trash for this product in case of damage or end life.

Guarantee certificate

Serie:………………………………………………………………………….
Date of purchase:………………………………………………………
Month / Year of manufacture:………………………………….
Reseller / Stamp:………………………………………………………

STETSOM INDUSTRIA ELETRÔNICA LTDA. – CNPJ: 61.974.911/0001-04
RUA MARIANO ARENALES BENITO, 645 – DISTRITO INDUSTRIAL – CEP 19043-130
PRESIDENTE PRUDENTE – SP