ADICOS HOTSPOT-X22 IR-Temperature Detector Instruction Manual
- June 9, 2024
- ADICOS
Table of Contents
ADICOS HOTSPOT-X22 IR-Temperature Detector Instruction Manual
Supplementary Instructions for HOTSPOT-X22 Article number: 410-2410-017 Index:
EN21 Release date: 26.02.2020
Translation
Manufacturer: GTE Industrieelektronik GmbH Helmholtzstr. 21, 38-40 41747
Viersen GERMANY
Support hotline: +49 2162 3703-0
E-Mail: support.adicos@gte.de
© 2020 GTE Industrieelektronik GmbH This document and all figures contained
may not be copied, changed, or distributed without explicit approval by the
manufacturer!
Subject to technical changes!
ADICOS® and GSME® are registered trademarks of GTE Industrieelektronik GmbH.
Abstract
The Advanced Discovery System (ADICOS) is used for early detection of fires in
industrial environments. It is comprised of various separate detector units.
With aid of suitable arrangement and parameterization the system meets a
specified detection goal, without being susceptible to interference.
The detector units are connected to the ADICOS Central Software with aid of the M-Bus. It allows the parameterization of each individual detector and the storage of all sensor data for statistical evaluation.
The ADICOS HOTSPOT-1000 is an IR fire detector used for optical and spatially resolved fire and heat detection. It is well suited for these applications:
- Detection of hot surfaces
- Detection of flames
- Detection of moving hot spots (pockets of embers)
- Monitoring of machinery and parts
ADICOS HOTSPOT-X22 detectors are designed for operation within explosive atmospheres of ATEX zone 22.
1 About this manual
1.1 Objective
This manual describes the special requirements on installation, wiring, commissioning, and operation of ADICOS detectors for explosive atmospheres of ATEX zone 22. They are exclusively addressed to knowledgeable specialist personnel (> Chap. 2, Safety instructions).
1.2 Explanation of symbols
This manual features a continuous structure for best possible comprehension.
The following labels are used.
Warning signs
This manual uses the following information types.
ℹ NOTE! Indicates information relevant to further operation of the
equipment.
⚠ WARNING! Signals a hazard that can cause death or serious injury.
⚠ DANGER! Indicates a hazard that will immediately cause death or serious
injury.
1.3 Storing the manual
Store this manual easily reachable and in direct vicinity of the detector system to enable use as needed.
2 Safety instructions
ADICOS HOTSPOT-X22 detectors for explosive atmospheres of ATEX zone 22 ensure operational safety assuming proper installation, commissioning, operation, and maintenance. For this purpose, it is absolutely required to completely read, understand, and follow this manual and the safety information contained.
⚠ WARNING! Installation and operating errors can lead to fatal and severe injuries and damage to the industrial plant.
- Read and follow this manual carefully!
2.1 Intended use
ADICOS HOTSPOT-X22 are designated for the detection of fire scenarios in explosive atmospheres of ATEX zone 22. In this context, the operating parameters described in Chap. 8, »Technical data« must be met. Any deviating use requires prior consultation with the manufacturer.
Compliance with this manual as well as all applicable country-specific provisions is also part of the intended use.
2.2 Standards and regulations
The safety and accident prevention regulations applicable for the specific application must be observed during detector installation, commissioning, maintenance, and test.
The following standards and directives are of particular importance when handling potentially explosive atmospheres:
2.3 Personnel qualification
Any work on ADICOS systems may only be performed by qualified personnel. Persons, who can perform work on electrical systems and recognize possible dangers based on their professional education, knowledge, and experience as well as knowledge of the applicable provisions, are considered qualified personnel.
⚠ WARNING! Installation, commissioning, parameterization, and maintenance may only be performed by authorized and respectively trained personnel
2.4 Handling electrical voltage
⚠ DANGER! The electronics of ADICOS HOTSPOT-X22 detectors requires an electrical voltage that can trigger an explosion in potentially explosive atmospheres.
- Do not open enclosure!
- De-energize the entire detector system and secure against unintentionally reactivation for all wiring work!
2.5 Modification
Any form of unauthorized modifications or extensions are expressively prohibited! In case of doubt, contact the manufacturer.
3 Structure
3.1 Overview
3.2 Cable assignment
4 Installation
4.1 Mounting on Mounting Plate
⚠ WARNING! ADICOS HOTSPOT-X22 detectors must be mounted with closed enclosure.
- Do not open enclosure!
- Use ADICOS mounting plate!
4.2 Mounting on Mounting Bracket
⚠ WARNING! ADICOS HOTSPOT-X22 detectors must be mounted with closed enclosure.
- Do not open enclosure!
- Use ADICOS mounting foot!
4.3 Wiring
⚠ DANGER! The electronics of the ADICOS HOTSPOT-X22 detectors requires an electrical voltage that can trigger an explosion in potentially explosive atmospheres.
- Do not open enclosure!
- De-energize the entire detector system and secure against unintentionally reactivation for all wiring work!
- In the case of wiring within potentially explosive atmospheres, only use ex-plosion-proof connection boxes with respective approval!
- Do not bend connection cable! Observe minimum bending radius! (> Chap. 8, Technical data)
5 Commissioning
⚠ DANGER! The electronics of the ADICOS HOTSPOT-X22 detectors requires an electrical voltage that can trigger an explosion in potentially explosive atmospheres.
- Prior to switching on, check that all detectors are properly mounted and wired!
6 Operation
DANGER!
The electronics of the ADICOS HOTSPOT-X22 detectors requires an electrical
voltage that can trigger an explosion in potentially explosive atmospheres.
- Never open the enclosure or loosen the cable gland during operation!
7 Maintenance
DANGER! The electronics of the ADICOS HOTSPOT-X22 detectors requires an electrical voltage that can trigger an explosion in potentially explosive atmospheres.
- Do not open enclosure!
- De-energize the entire detector system and secure against unintentionally reactivation for all wiring work!
- Replace the closed detector including connection cable only!
8 Technical data
ℹ NOTE!
ADICOS X22-Detectors are rated Protection by enclosure “tc”.
- An Ex barrier is not mandatory!
9 Appendix
9.1 ADICOS Mounting Plate
9.2 ADICOS Mounting Bracket
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>