STETSOM BRACO Full 1200 Digital Amplifier User Manual

FULL
MODEL:
1200
DIGITAL AMPLIFIER
USER MANUAL

Introduction

Thank you so much for choosing a Stetsom product! This amplifier was developed with cutting-edge technology for those who want high quality sound from audio systems with one or more speakers or even an audio wall system.

Before installing

Please read this manual carefully.

• All connections must be made with the product turned OFF.
• A fuse must be installed between the amplifier and the battery is required to protect against overcurrent. The fuse needs to be installed as close to the battery as possible. Choose an appropriate fuse for the amplifier based on its consumption.
• Use the wire recommended in this manual to keep cables from overheating cables and to obtain maximum power.
• Keep the cables as short as possible to increase sound fidelity and avoid potential power losses.
• Route the installation cables as far away as possible from the original vehicle wiring to prevent interference and noise in your audio system.
• Perform the installation on a firm surface in a ventilated and dry place.
• Installation should only be done by a qualified professional.

If you have questions , contact the store where the purchase or installation was done. For more information please contact our Customer Service: BR +55 18 2104-9412.

Input, output and audio controls

1. RCA JACK INPUT: Input of the signal to be amplified. Connect to the radio/ player using high quality shielded RCA cables to prevent unwanted noise.

2. LEVEL: Level control for the signal at the amplifier’s input.

3. CROSSOVER:
   ▪ HIGH PASS FILTER (H.P.F.): This variable control allows you to select the initial frequency from 10Hz ~ 90Hz that will be reproduced by the amplifier.
   ▪ LOW PASS FILTER (L.P.F.): This variable control allows you to select the final frequency from 90Hz ~ 15KHz that will be reproduced by the amplifier.

4. BASS BOOST:
   ▪ BASS: Variable control for bass boost from 0dB ~ +10dB.
   ▪ FREQ: Variable control for BASS boost frequency from 30Hz ~ 70Hz.

5. FLAT KEY: This switch allows you to turn the FLAT mode on or off. Settings made on the CROSSOVER and BOOST controls will be turned off when using this mode.

6. COOLER: It cools the amplifier. Install in a cool place being careful to not obstruct the air vents.

Power input

7. OUTPUT CONNECTOR (SPEAKERS): MONO output of amplified signal for speakers connection. Check the minimum impedance and polarities before
   performing the installation.

8. POSITIVE POWER SUPPLY CONNECTOR: Connect to the positive battery terminal of the battery using a minimum 6 AWG cable with a fuse/circuit breaker installed as close to the battery as possible.

9. REMOTE CONNECTOR (REM): Allows automatic activation of the amplifier when turning on the radio/player. Connect to the remote output of the radio/player using a cable a minimum of 18 AWG.

10. NEGATIVE POWER SUPPLY CONNECTOR: Connect to the negative terminal of the battery using a cable with a minimum of 6 AWG.

Indicators LED

Smart protection system

When the protection system detects a failure, the amplifier will turn off and the PROT LED will blink. For each type of failure, the LED will flash a certain number of times indicating the cause, as shown in the table below:
Diagnostic: Short circuit or output overload.
Solution: Check that the speaker cables are well insulated and that the output impedance does not exceed that supported by the amplifier.
Diagnostic: Excessive temperature. When the amplifier reaches approximately 194°F, audio is stopped and the coolers run at maximum speed to speed up the cooling process of the internal components.
Solution: Check if the amplifier is in a ventilated place or if the coolers are not obstructed. Keep the amplifier turned on for a few minutes for the coolers to assist in the cooling process.
Diagnostic: Supply voltage less than 9V.
Solution: Check voltage of battery or power supply.
Diagnostic: Supply voltage greater than 15V.
Solution: Check voltage of battery or power supply.

Instalation

Specification of the cables for proper installation:

• Power connectors (positive/negative) ……………………….6 AWG
• Remote connector …………………………….18 AWG
• Output signal connectors (speakers) ………………….11 AWG
• Fuses or circuit breakers ………………………….70A
  The use of a fuse or circuit breaker is mandatory to protect the system from short circuits and overload. Install them as close to the battery as possible.

**** Installation should only be done by qualified professionals with the product turned OFF.

Troubleshooting

AMPLIFIER DOES NOT TURN ON:

• Verify that the cables are connected correctly. Make sure all connections  have electrical and mechanical contact.

• Fuses or circuit breakers may be defective or blown. Check the condition of the circuit breakers and make sure they are compatible with the equipment consumption.

• Make sure that the battery is charged sufficiently for the product to operate.
  NO SOUND:

• The cables to the speakers or RCA plugs may not be connected incorrectly or defective.

• Make sure that the LEVEL control is not at a minimum.
  PROT LED FLASHING:

• Make sure that the product’s air vents are not blocked and that the product is not overheating.

• Speakers or cables are shorted. Check speakers, cables and connections.
  SOUND DISTORTIONS:

• The speakers may be overloaded or defective, lower the level and then readjust the level. This setting can be adjusted as follows:

a) On the radio/player, play any musical signal and set the volume to 80% of the maximum (if the maximum volume of the radio /player is 45 (100%), set to 36 (80%).
b) On the amplifier, begin with the LEVEL control at minimum, increase gradually until the LED CLIP starts to flash. Slowly decrease the LEVEL until the led goes out completely.
WEAK OF BASS:

• Cables of the speakers may be reversed and (speakers out-of-phase).
  NOISE AND FAILURE IN SOUND:

• Make sure that the installation is not close to the vehicle’s original wiring as it may cause interference and noise in the audio signal.

• Create a separate power connection for the sound system. Use a fuse/ circuit breaker as close to the battery as possible for protection.

• Make a good grounding for the amplifier. To do this, remove the paint from the vehicle chassis at the desired point. Attach the wire using a ground terminal. To prevent oxidation, isolate with paint.

• Do not loop the ground. Avoid using multiple grounds. If possible, use a star connection, so all the grounds run from a single point.

** The data measured are based on STETSOM laboratory equipment. Test reference in frequency from 60hz to 1Khz with THD + N at ≤1% in impedances as indicated in each measurement. The electronic components and the manufacturing process may present manufacturing variations, thus leading to a variation in the measurements made.
Any updates made in this manual will be available for customers to consult free of charge on the brand’s site. It is recommended that the updated manual be consulted whenever needed.
Images contained in this manual are merely illustrative and may differ from the actual product.**

Technical specifications

900W RMS @ 4 Ohms
Power output @ 12.6V:| 1250W RMS @ 1 Ohm
750W RMS @ 2 Ohms| 1240W RMS @ 2 Ohm
700W RMS @ 4 Ohms
Minimum input sensitivity:| 200mV
Minimum input sensitivity:| 200mV
Signal to noise ratio:| >90dB
Frequency response (-3dB)| 10Hz ~ 15KHz
Crossover low pass:| 90Hz ~ 15KHz
Crossover high pass:| 10Hz ~ 90Hz
Bass boost:| Freq: 30Hz ~ 70 Hz
Boost: 0dB ~ +10dB
Input impedance:| 10K Ohms| 12K Ohms
Supply voltage:| 9V ~ 15V DC
Musical consumption:| 63.5A| 60A
Bass consumption:| 127A| 120A
Dimensions (H x W x L):| 3.14” x 9.11” x 5.78”
Weight:| 3.85 lb| 3.63 lb

Warranty Term

STETSOM, through its network of Authorized Technical Assistance Providers, guarantees technical assistance to the purchaser of their products. The repairs of any defects duly established as being of the manufacturer will be done without cost for replacement components or parts and repair labor.
The repairs will be done by the Authorized Technical Assistance Provider specially designated by STETSOM.
CONSULT THE LIST OF AUTHORIZED TECHNICAL ASSISTANCE PROVIDERS ON OUR WEBSITE: www.stetsom.com.br/en/assistencias-tecnica
If you do not locate technical assistance in your city, please contact us at: BR +55 18 2104-9412
WARRANTY CONDITIONS:
Our warranty is 1 (one) year against manufacturing defects. Its validity starts on the date of the Sale to the FINAL Consumer.
To claim the benefits of this warranty, you must present one of the following documents: the Final Consumer’s SALE NOTE or this completed CERTIFICATE.
SITUATIONS THAT VOID THE WARRANTY:

1. 1 year after the issuance of the invoice of sale to the consumer or 1 year after the certificate of warranty is filled out (dated and stamped by the retailer or installer) or 1 year from date of manufacture.
2. Violation of seals, alteration or removal of the product’s serial or lot number.
3. If the product suffers misuse or careless accidents involving: Water, Fire or Fall, or is installed in conditions contrary to the guidelines contained in the installation manual that accompanies the product.
4. Damages and changes in the circuit or adaptation of non-original parts.
5. If you use installation techniques contrary to those given in the manual.

QUESTIONS AND ADVICE:
STETSOM offers Customer Services to answer questions and give advice about their products and services. Please contact us through the channels:
Phone: BR +55 18 2104-9412 — E-mail: suporte@stetsom.com.br
Site: www.stetsom.com

Statement of conformity

EUROPE – Declaration of Conformity < EU-DoC >
** Hereby, STETSOM INDUSTRIA ELETRÔNICA LTDA declares that this equipment type is in-compliance with Directive 2014/30/EU. The full text of the EU declaration of conformity is available at the following internet address:=
1 OHM
MODEL: BRAVO FULL 1200 (1Ω)
Voltage Supply: 9V – 15V DC
Current Range: 1.0A – 127A
MADE IN BRAZIL
www.stetsom.com.br/certifications/bravo-full_1200_1ohm_eu- doc.pdf
2 OHMS**
MODEL: BRAVO FULL 1200 (2Ω)
Voltage Supply: 9V – 15V DC
Current Range: 1.0A – 120A
MADE IN BRAZIL

www.stetsom.com.br/certifications/bravo-full_1200_2ohms_eu- doc.pdf
Waste Electrical and Electronic Equipment (WEEE)
The European Union (EU) WEEE Directive (2002/96/EC) places an obligation on producers (manufacturers, distributors and/or retailers) to take-back electronic products at the end of their useful life. The WEEE Directive covers most HME products being sold into the EU as of August 13, 2005. Manufacturers, distributors and retailers are obliged to finance the costs of recovery from municipal collection points, reuse, and recycling of specified percentages per the WEEE requirements.
Instructions for Disposal of WEEE by Users in the European Union
**** The symbol shown below is on the product or on its packaging which indicates that this product was put on the market after August 13, 2005 and must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of the user’s waste equipment by handing it over to a designated collection point for the recycling of WEEE. The separate collection and recycling of waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects
human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local authority, your household waste disposal service or the seller from whom you purchased the product.

Guarantee certificate

Serie:
Date of purchase:
Month / Year of manufacture:
Reseller / Stamp:

STETSOM INDUSTRIA ELETRÔNICA LTDA. – CNPJ: 61.974.911/0001-04
RUA MARIANO ARENALES BENITO, 645 – DISTRITO INDUSTRIAL – CEP 19043-130
PRESIDENTE PRUDENTE – SP
STETSOMBRASIL
GRUPOSTETSOM
STETSOMBRASIL www.STETSOM.com.br
R1

References

• Stetsom - Stetsom
• Stetsom - Stetsom
• Assistências TécnicaTechnical AssistanceAsistencias Técnica - Stetsom
• Assistências TécnicaTechnical AssistanceAsistencias Técnica - Stetsom
• Assistências TécnicaTechnical AssistanceAsistencias Técnica - Stetsom

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>