VIMAI V19 Open Wearable Stereo Instruction Manual

VIMAI V19 Open Wearable Stereo Instruction Manual

Product Diagram

Earphone Parameters

Product name : Open wearable stereo:
Transmission range : 2402-2480MHz
Battery capacity : 50mAh
Supported protocol: HSP/HFP/A2DP/AVRCP
Charging current : about 40mA
Transmission frequency : 2.4GHz
Frequency response range : 20HZ-20KHZ
Charging time : about 1.5 hours
Product impedance : 160±15%
Call time : About 6 hours
Sensitivity: 118dB+/-3@1kHz
Music time : about 8 hours (50% volume)
Size: 49.4833.613.5mm
Stand-by time : about 1 year
Working distance: 10m
Charging voltage/current : 5V/1A standard environment)
Product operating temperature : -10°C~+45℃
Weight : 6.8g(without storage box)
Product storage temperature : -20°C~+65°C
Bluetooth version : V5.4

Packing list

• Charging Case

• Earphones

• Charging Cable

• User Manual

Operation Instruction

Power on

1. Open the charging case, and the earphones will turn on automatically
2. Touch for 3 seconds to power on

IOS and Android systems connect the earphones Turn on Bluetooth, search for Bluetooth device “V19”, The first time you need to manually connect the device, connect “V19”

Power Off

1. Put it in the charging case and turn off
2. Press and hold for 6 seconds to turn off
3. Power on for 3 minutes without connection automatically turn off

Earphone Function Illustrate

**L

**

• Answer the call : Single Click
• Hang up: Double click
• Call rejection : Press for 1S
• Play/Pause : Double click
• Previous: Triple click
• Voice assistant : Press for 2S

**R

**

• Answer the call: Single Click
• Hang up: Double click
• Call rejection: Press for 15
• Play/Pause: Double click
• Next : Triple click
• Voice assistant : Press for 2S

Both Earbuds can be switched freely
The left and right earbud can be connected to the mobile phone, switch freely, and connect back in seconds after booting.

Tone/ Lighting Effect Description

Charging Case Definition Description

charging and goes out when fully charged
Right ear bud: green light flash when charging and goes out when fully charged
Put the car buds in the case| Civet car bud: bloc light flash once when put in or take out Right ear bud, green light flash once when put in or take out
Open/Close the charging case| Earphone turn on and the charging case light display the current battery for 3 seconds
Battery indicator| The red light flashing below 20%, and the green light is on above 20%

Charging Case Parameter Description

Battery capacity: 400mAh
Charging case product size : 736827mm
Charging port: Type-C
Battery life: about 3-4 times
Charging voltage/current : 5V/1A
Operating temperature : -10°C~+45°C
Charging time : about 1.5 hours
Storage temperature: -20°C~+65°C

Restore factory settings

Put the earphone into the charging case and keep the case open, hold the left/right earphone touch area for 8 seconds. The Orange light will flash for 3 seconds and then factory reset.

Safety Guidelines

1. Please follow the instructions in this manual, do not disassemble or modify the device for any reason, otherwise it may cause the earphones to malfunction or burn
2. Do not infiltrate the product into any liquid or waler to rinse the product
3. Do not use a charger other than the rated current and voltage of the headset (5V/1A) to charge the headset, otherwise It is easy to cause damage to the earphone battery (please use the matching charging cable to charge the earphone)
4. Please use and store this product in a normal temperature environment, do not place the device in an environment where the temperature is too low or too high(below 0 or above 45°)
5. Do not block the openings of the headset, such as the charging port, indicator light and microphone, etc.
6. Please avoid using headphones at excessive volume or for too long to avoid dizziness or damage to hearing
7. Do not use the device under thunderstorm weather, which may cause the device to work abnormally and the signal to be interrupted.

Warranty card

User Name:……
User Number:….
User Address:…..
Purchase Date:…..
Invioce Number: ….
Seller: After-sales Provider: ….
**After-sales Number: …..

**

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement

The device has been evaluate to meel general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>