GPO Personal Cassette Player with Bluetooth User Manual

GPO Personal Cassette Player with Bluetooth User Manual

Location of controls

1. Cassette Door
2. Stop Button
3. Fast Forward Button
4. Play Button
5. Rewind Button
6. Record Button
7. Built-in Microphone
8. Volume Control Knob
9. Bluetooth On/Off Switch
10. Bluetooth LED Indicator
11. Phone Jack
12. DC Jack
13. Battery Compartment
14. Speaker
15. Touch Control Area
16. Power LED Indicator
17. USB Socket

Powering your Personal Bluetooth Cassette Player

The unit is powered with either two AA (UM-3) batteries or an AC/DC adaptor. Please note: Both the batteries or AC/DC adaptor are not supplied.

Using batteries (NOT SUPPLIED)

1. Open the Battery Compartment (13) on the back of the unit by sliding open and gently pulling upwards the battery door.
2. Check the polarity (+/-) inside the battery compartment.
3. Insert two AA (UM-3) batteries according to the polarity.
4. Close the battery door.

For best performance and extended operating time, we recommend using alkaline batteries.

Using an AC/DC adaptor (NOT SUPPLIED)

1. Insert the DC plug (at the end of the AC adaptor cord) into the DC Jack (12) on the bottom of the unit.
2. Plug the AC adaptor into a 220/230V~ 50Hz AC power socket.
3. The unit will automatically disconnect from using battery power and operate using the AC/DC adaptor.

Playing Cassette Tape

1. Insert the provided Earphones plug into the Phone Jack (11).

2. Put on the Earphones.

3. The unit has a built-in speaker (14), it will be working alternatively if you don’t connect Earphones to the Phone Jack (11)

4. Open the Cassette Door (1) and insert a pre-recorded cassette tape face upwards.

5. Close the Cassette Door (1).

6. Press the Play Button (4).

7. Adjust the Volume Control Knob (8) to your preferred sound level.

8. Press the Fast Forward Button (3) if you wish to rapidly advance the cassette tape.
   Press the Stop Button (2) after you have advanced to the desired point on the cassette tape.

9. Press the Rewind Button (5) if you wish to rapidly rewind the tape.
   Press the Stop Button (2) after you have rewound to the desired point on the cassette tape.

10. Press the Play Button (4) to start to listen the cassette tape again.

Recording into Cassette Tape

1. Insert an empty cassette tape as previously described. Press the ORANGE Colour Record Button (6) & the Play Button (4) will be
   depressed with it. You are now recording. If the Record Button (6) cannot be pressed down, see “PREVENT ACCIDENTAL
   ERASURE”.

2. Talk normally into the Built-in Microphone (7). To obtain optimum recording quality, place the unit with the Built-in Microphone (7)
   freely exposed and as close as convenient to the sound source.

3. You can press the Rewind Button (5) to go back to the beginning of the cassette tape, make another recording to cover the previous recording.

Connecting with the Bluetooth Headphones

1. Charge the Bluetooth Headphones via the USB Socket (17) with the provided USB charging cable, the Power LED Indicator (16) will be light on in Red during charging. It will be light off after the headphones has been fully charged
2. During playing the cassette tape, slide the BT On/Off switch (9) to the “ON“ position, the Bluetooth LED Indicator (10) will be flashing
3. Put on the fully charged Bluetooth Headphones, touch & hold on the Touch Control Area (15) until hearing voice prompt “Power On”, the Power LED Indicator (16) will be flashing in Red & Blue quickly.
4. The connecting will be started automatically between the Bluetooth Cassette Player & the Bluetooth Headphones.
5. You will hear voice prompt “Start Pairing” & the connecting process can be taking up to 20 seconds.
6. Then you will hear voice prompt “Parties Connected” when the connecting process is completed, the Bluetooth LED Indicator (10) on the Bluetooth Cassette Player will light on & the Power LED Indicator (16) on the Bluetooth Headphones will be flashing slowly in Blue only.
7. You can now listen to the music on the cassette tape by using your Bluetooth Headphones.
8. Adjust the Volume Control Knob (8) to your preferred sound level.
9. To turn off the Bluetooth Headphones, just touch & hold again on the Touch Control Area (15) until hearing voice prompt “Power Off”, the Power LED Indicator (16) will be light off.

Automatic stop

• To protect your cassette tapes and prevent unnecessary wear to the cassette mechanism, this unit is equipped with an automatic stop system.
• When the tape ends during playing, the Play Button (4) automatically releases, which stops the cassette from running.

Cassette tape operating tips

• Tapes with a playing time of 120 minutes (C-120) are not recommended. These contain thinner and longer tape, which has a
  greater chance of malfunctioning and/or jamming, and may damage the cassette mechanism.

• To ensure good reproduction, please clean the head after every 10-20 hours of use.

• Keep the Cassette Player away from excessive heat or cold.

• If there is slack in the tape, remove the slack prior to inserting the cassette. To remove the slack, insert a pencil into the hub and rotate clockwise (see below).

Leader tape

• There is a ‘leader tape’ at the beginning on each cassette tape. There is no recording on this area. Always allow the tape to run for about five seconds to reach the recording tape.
• Always keep the tape head clean. A dirty head can cause distorted sound or improper tape speed.

Hereby ProtelX, declares that this equipment (GPO Personal Cassette Player with Bluetooth) is in compliance with the essential requirements and other relevant provisions of Directive, you can access a copy of this certificate on
www.gporetro.com/Certificate-ofConformity

www.gporetro.com
IMPORTED AND DISTRIBUTED BY:
ProTelX Ltd, Unit 6, Park 17 Industrial Estate, Moss Lane,
Whitefield, Manchester, M45 8FJ UK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>