EXCELL PRECISION SUBe AirCharge Wireless Charging Waterproof Weighing Scale User Guide
- August 17, 2024
- EXCELL PRECISION
Table of Contents
EXCELL PRECISION SUBe AirCharge Wireless Charging Waterproof Weighing
Scale
SUBe /SUBe Air Charge Quick Startup Guide
Usage Notice
- Use within the maximum capacity. A void sudden drop of heavy object on the platter
- Use under a stable temperature and air flow. Avoid direct sunlight or use near air vent.
- Use under individual socket to avoid the interference of other electric appliances.
- Put the scale on a firm and flat surface for accurate weighing reading. Adjust the four leveling feet to get the leveling bubble at the center of the circle.
- Clear the platter before turning on the scale. It requires 15 ~ 20 minutes to warm up.
- For accurate results, place center of the object in the center of platter.
- When the low power warning symbol flashes, If not charge immediately, auto shuts down within 5 10 hours or 1 2 hours with backlight. Once it auto shuts down and enters the battery protection mode, it must be charged before it can be used.
- Please operate or charge the scale in an open area. Avoid squeezing the power cable, which might cause short circuit within cable and result in fire. B attery temperature should be < 45°C while charging. Red –> charging is in progress. Blue –> The battery is fully charged If scale is fully charged, after plugging in, the blue light will turn on after about 5 ~10 minutes of voltage detection. N ewer scales have symbol. Please unplug the AC power cable and turn scale on to check the battery symbol for the amount of power left
- The rechargeable battery is consumables and is not included in the warranty. If scale is not used for some time, recharged it every six months and recharged it before use. Avoid store at a high temperature environment, the ambient temperature should be less than 50
- After installing the battery, if no display when power is turned on, please check whether the battery polarity is reversed. The polarity must be installed correctly to avoid battery power wasted away.
- When Charging indicator flashes in the charging state, it means there are the following abnormal states, please check
- a) battery is installed but the contact is poor, please check whether the battery is installed properly
- b) please check whether the polarity of the battery is reversed.
- c) When the battery is removed and the AC power cord is still plugged in. When plugged in without the battery installed, there will be a slight frequency conversion sound, which is normal and does not affect the use of the function.
- SUBe AirCharges wireless charging pad should be within 2mm of scale. When charging, no metal objects should be placed between the charging pad and scale. Otherweise, it may cause heat or burn. To charge, first plug adaptor into power socket, then place the charging pad in to the indentation at the bottom of the scale and check if the charging light turns on in about 5 seconds. If charging light turns on, charging is in process. If charging light is still off, charging pad is not fully intact in place or it is not detected while sliding in. Please pull out charging pad and install it again
- Our product uses a single cell cylindrical 18650 3.7V lithium ion battery. B attery s should be 3.6~3.7V and capacity is not restricted. If the appearance of the battery is deformed, damaged, etc., please do not install it for the safety of use.
FnC 00 Back to the Previous Level|
---|---
FnC 01 Power Saving| on-> enable power saving, off-> disable power saving
FnC 02 Automatic Power-off| 0->disable, 1~9-> Time in mintues to auto power
off
FnC 03 Hi/Lo/OK| See below. To disable, set both high limit and low limit to
“0”,
FnC 08 Two Weighing Units
| 0: disable the 2nd weight unit;
To set the 2nd weight unit to => 1:2nd unit in CSP 01 2: 3rd unit in CSP 01 3: 4th unit in CSP 01
FnC 09 Unstable Tare| 0: disable 1: enable tare operation while unstable
FnC 10 LED Brightness| 3: High 2: Normal 1: Low
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. The antennas used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter.
FCC Statement:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC ID for charging pad: 2BFJV000001.
EXCELL Precision Co., Ltd.
6F, No. 127, Lane 235, Baoqiao Rd.,
Xindian District,
New Taipei City 23145
TEL : 886 2 8919 1000
Fax: 886 2 8919 2209
Email : pm-all@excell.com.tw
www.excellscale.com
Documents / Resources
|
EXCELL PRECISION SUBe AirCharge Wireless Charging Waterproof Weighing
Scale
[pdf] User Guide
SUBe, SUBe AirCharge Wireless Charging Waterproof Weighing Scale, AirCharge
Wireless Charging Waterproof Weighing Scale, Wireless Charging Waterproof
Weighing Scale, Charging Waterproof Weighing Scale, Waterproof Weighing Scale,
Weighing Scale, Scale
---|---