Choetech T201-F Wireless Charger User Manual
- October 30, 2023
- CHOETECH
Table of Contents
Choetech T201-F Wireless Charger
Product Information
The T201-F is a wireless car charger that comes with two mounting options – air vent mount and suction cup mount. It has a quick-release button for easy removal of the phone and supports fast charging function with a QC3.0 Quick Charger power adapter (not included). The product requires a Qi-enabled device or a device installed with a Qi receiver kit.
Product Usage Instructions
Before using the product, please read the user manual carefully and keep it for future reference. Pay particular attention to the safety instructions.
Package Check
Check your package before use. If you get the air vent mount, follow Option 1 for installation. If you get the suction cup mount, follow Option 2 for installation.
Option 1: Installation of Air Vent Mount
- Assemble the Mount: Remove the adjustment knob from the back of the wireless charger and place it over the ball joint on the air vent mount. Connect the ball joint to the wireless charger and tighten the knob.
- Mount on the Air Vent: Insert the air vent mount into the car air vent lever. Firstly turn the switch to direction 1. If too loose, turn to direction II.
- To Install and Remove the Phone: Put your phone on the car charger and slide down until your phone is secured. To remove, press the quick-release button on any side and take your phone out.
Option 2: Installation of Suction Gup Mount
- Assemble the Mount: Remove the adjustment knob from the back of the wireless charger and place it over the ball joint on the suction cup mount. Connect the ball joint to the wireless charger and tighten the knob.
- Mount on the Flat Surface: Remove the plastic cover on the suction cup. Clean the desired mounting surface. Move the suction lever to the raised position. Place down the dock on the flat surface and press down firmly. Press the suction lever fully down to mount the dock on the surface. Note: To release the mount, lift up the lock lever and pull up the release tab.
- To Install and Remove the Phone: Put your phone on the car charger and slide down until your phone is secured. To remove, press the quick-release button on any side and take your phone out.
Telescopic Knob and Pivot Knob
The product has a telescopic arm with a telescopic knob and a pivot knob. Loosen the telescopic knob to extend the arm and tighten it to secure the distance. Turning the pivot knob allows you to pivot the arm. Tighten it to secure the position.
Attention
- Do not close the car charger with magnetic stripe or chip card (D card, bank card, etc.) to avoid magnetic failure.
- Please make sure that your device is Qi-enabled or installed with a Qi receiver kit.
- A QC3.0 Quick Charger power adapter (not included) is required to support fast charging function.
- Please use the USB cable attached.
- Suggest removing the protective case during charging period.
- Be careful about the hook behind when you take out the car charger from your car.
Dear customer,
Thank you for purchasing our product. Please read the following instructions
carefully before first use and keep this user manual for future reference. Pay
particular attention to the safety instructions. If you have any questions or
comments about the device, please contact the customer line.
Specifications
Input 5V – 12V 2A (Max)
Output 15W (Max)
Product Diagram
Please check your package before use, if you get air vent mount, please follow “Option 1” to install your devices; if you get the suction cup mount, please follow “Option 2” install your devices.
Installation of the Wireless Charger
Option 1: Installation of Air Vent Mount
- Assemble the Mount: Remove the adjustment knob from the back of wireless charger and place over blloint on air vent mount Connect the ball joint to the wireless charger and tighten the knob.
- Mount on the Air Vent: Insert the air vent mount into the car air vent lever Firstly turn the switch to direction 1. If to loose, turn to direction II.
- To install and Remove the Phone: Put your phone on the car charger and slide downuntil your phone is secured. Removal: Press the quick-release button on any side and take your phone out.
Option 2: Installation of Suction Gup Mount
-
Assemble the Mount: Remove the adjustment knob from the back of wireless charger and place over all oint on suction cup mount Connect the ball joint to the wireless charger and tighten the knob.
-
Mount on the Flat Surface: Remove the plastic cover on suction cup Clean the desired mounting surface.
Move suction lever to the raised position Place down the dock on flat surface and press down it firmly.
Press the suction lever fully down to mount the dock on surface.
Note: To release the mount, lift up the lock lever and pull up the release tab. -
To install and Remove the Phone: Put your phone on the car charger and slide down until your phone is secured.
Removal: Press the quick-release button on any side and take your phone out. -
Telescopic Knob: Loosen it to extend the telescopic arm, and tighten to secure distance.
-
Pivot Knob: Turning allows you to pivot telescopic arm. Tighten to secure position.
Attention
- Do not close the car charger with magnetic stripe or chip card (D card, bank card, etc.) to avoid magnetic failure.
- Please make sure that your device is Qi-enabled or installed with Qi receiver kit.
- A QC3.0 Quick Charger power adapter (Not included) is required to support fast charging function.
- Please use the USB cable attached.
- Suggest removing the protective case during charging period.
- Be careful about the hook behind when your take out the car charger from your car.
EU Declaration of Conformity
This equipment is in compliance with the essential requirements and other
relevant provisions of EU directives.
www.alza.co.uk/kontakt
✆ +44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7,
www.alza.cz
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>