Sonoff TX Wi-Fi Smart Wall Switch User Manual
- June 6, 2024
- SonOFF
Table of Contents
Sonoff TX Wi-Fi Smart Wall Switch
Specifications
Max. input| T0/T2/T3( US1C )：AC 100-240V 50/60Hz 2A T0/T2/T3( US2C
)：AC 100-240V 50/60Hz 4A T0/T2/T3( US3C )：AC 100-240V 50/60Hz 6A
---|---
Max. output| T0/T2/T3( US1C )：AC 100-240V 50/60Hz 2A
T0/T2/T3( US2C )：AC 100-240V 50/60Hz 2A/Gang 4A/Total T0/T2/T3( US3C )：AC
100-240V 50/60Hz 2A/Gang 6A/Total
LED load| 150W/110V(per channel)，300W/220V(per channel)
Wi-Fi standard| IEEE 802.11 b/g/n 2.4GHz
RF| 433.92MHz
Operating systems| Android 4.1 or higher & iOS 9.0 or higher
Materials| PC +tempered glass panel
Dimension| 120x74x38mm
T0(US1C/US2C/US3C) does not support the remote controller with 433.92MHz.
Product Introduction
Wi-Fi LED indicator status instruction
| Wi-Fi LED indicator flashes (one long and two short) | Quick pairing mode |
|---|---|
| Wi-Fi LED indicator keeps on | Device is connected successfully |
| Wi-Fi LED indicator flashes quickly once | Unable to discover the router |
| Wi-Fi LED indicator flashes quickly twice | Connect to the router but fail to |
connect to Wi-Fi
Wi-Fi LED indicator flashes quickly three times| Upgrading
Features
Turn on/off the light or fan from anywhere, schedule it power on/off and share it with your family to control together.
Factory Reset
Long press any button you desired to pair for about 5s until the Wi-Fi LED
indicator changes in a cycle of two short and one long flash and release, then
the reset is successful. The device enters quick pairing mode (Touch).
Please reset the switch to factory defaults if you want to use other Wi-Fi networks, then reconnect the network.
RF Remote Controller Pairing
The switch supports the remote controller with 433.92MHz frequency brand to turn on/off, and each channel can learn it independently, which is local short-range wireless control not Wi-Fi control.
Pairing Method:
Long press the touch button you want to pair for 3s until you hear a “beep”
sound and release, then press the corresponding button on the RF remote
controller, and you will hear a “beep” sound again after successful pairing.
Other buttons can be paired through this method.
Clearing Method:
Long press the touch button you want to clear for 5s until you hear two “beep”
sounds and release, then press the corresponding button on the RF remote
controller, and you will hear a “beep” sound again after successful clearing.
Other buttons can be cleared through this method.
Common Problems
Q: Why my device stays “Offline”?
A: The newly added device needs 1 – 2mins to connect Wi-Fi and network.
If it stays offline for a long time, please judge these problems by the blue
Wi-Fi indicator status:
-
The blue Wi-Fi indicator quickly flashes once per second, which means that the switch failed to connect your Wi-Fi:
-
Maybe you have entered a wrong Wi-Fi password.
-
Maybe there’s too much distance between the switch your router or the environment causes interference, consider getting close to the router. If failed, please add it again.
-
The 5G Wi-Fi network is not supported and only supports the 2.4GHz wireless network.
-
Maybe the MAC address filtering is open. Please turn it off.
If none of the above methods solved the problem, you can open the mobile data network on your phone to create a Wi-Fi hotspot, then add the device again. -
Blue indicator quickly flashes twice per second, which means your device has connected to Wi-Fi but failed to connect to the server.
Ensure a steady enough network. If double flash occurs frequently, which means you access an unsteady network, not the product problem. If the network is normal, try to turn off the power to restart the switch.
Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park, shenzhen, GD, China ZIP code: 518000
Website: sonoff.tech
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>