Veken B07PRKYJR8 Dual Probe Wireless Digital BBQ Thermometer with Timer and Touch Screen User Manual

CONTENTS
1.1 Package Content 1.2 Product Description 1.3 Specifications
2.1 Installing Batteries 2.2 Assembling the Transmitter
3
4.1 Thermometer Mode 4.2 Timing Mode

1.1 Package Content
01 01 01 06
07
07 07
08

08

08

14

1.2 Product Description

18

19

can

20

21

01

1.2.1 Transmitter Features
Probe 1 Probe 2

1.2.2 Receiver Unit Feature

Function keys

and

æ Touch

to turn on the backlight. Hold

for 3 seconds to turn ON/OFF

the LCD. When powered On, the transmitter will display the data. When powered Off

and then On again, it will re-launch the temperature.

ç Touch

to switch

Choose timer mode
5 function keys LIGHT and touch buttons

and MODE.

02

03

LIGHT :
æ Hold LIGHT to power ON/OFF (OFF function only turns off the display and stops the time to power saving mode. When the battery is on, hold LIGHT to turn on the display and restore the previous setting. When the battery is off and on reset, hold LIGHT to turn on the default display and the default setting).

MODE : Toggle between four-bit time display mode and timing mode. Power on the default 24-hour
system of four-digit time display mode; the icon “:” flashes and “TIME” appears.

æ Time Display Mode(000): Press and hold MODE for 3 seconds and click

to set the

time system following the sequence: 12 -> 24H, click MODE, then click

to set the

time following the sequence: hour ­> minute.

ç Timing Mode (0H00M00S) : Timing maximum range: 9H59M59S. Timing and barbecue can run

dual tasks.

Count Up Time: Click MODE to switch the timing mode (0H00M00S), and click

Count Down Time: Press and hold MODE for 3 seconds and click MODE to set time following

the sequence: H->M->S, click

to start the countdown, You will hear a “didi” alarm

and the orange light will flash.

04

æ When the battery is on, the default display is Probe 1 and Probe 2, meat and taste for Probe 1:

defaults to BEEF and WELL.

ç To select the type of meat you want to cook, press the

button. The monitor displays the

type of meat the thermometer is ready to measure. Each press will change the display in the

following sequence: BEEF -> LAMB -> VEAL -> HAM -> PORK -> TURKY -> CHICK -> FISH ->

PROG -> BEEF.

èHold

for 3 seconds to switch the meat and taste of Probe 1 or Probe 2. The sequence

is PROBE 1 -> PROBE 2. Hold

and at the same time for 3 seconds to clear the RF data.

é Press

once and upwards and hold for 3 seconds to go ahead in the 8 step/second speed.

Press T once and backwards and hold for 3 seconds to go back in the 8 step/second speed.

æ To select the taste level of the meat you want to cook, press the

button. The different taste

options in the sequence are: WELL / MED WELL / MEDIUM / MED RARE / RARE

ç Hold the button to switch between and ¥

05

æ Hold the

button for 3 seconds, “TEMP SET” will start to flash. Press

and

to adjust the temperature setting, and press

to confirm the settings. This setting mode will

remain in place without any activity for 30 seconds.

ç Press

to turn on/off the alert function, the alert icon appears, the sequence is probe 1

ON – probe 2 ON- probe 1 & probe 2 ON – probe 1 & probe 2 OFF. è When alert function is ON, it will signal the alarm once it reaches the alert temperature, the alert

icon will flash, the orange light will flash, probe 1 beeps B1 for 1 second, and probe 2 beeps BIBI

for 1 second.

2.1 Installing Batteries
Remove the hanger and battery compartment. Insert 2 AAA batteries.

1.3 Specifications

Wireless Transmission Distance Temperature Range Temperature Accuracy Timing Range
Preset Temperature Range Waterproof Grade(Probe)

328 ft. (100 metersin open space -4 to 572c-20¥ to 300¥ ±1.8 c±1¥ 000000-95959 USDA doneness levels IPX7

2.2 Assembling the Transmitter
NOTE: If the probe is not connected to the transmitter, the current temperature will display LLL.
the probe is not connected

06

07

3

Press the

button on

the receiver to turn On/Off.

Press the

button on

the transmitter to turn On/Off.

4.1.1 Preset USDA Doneness Temperature

4.1 Thermometer Mode
You can use 2 probes to measure and monitor 2 pieces of meats, or 2 sections of the same large piece of meat at the same time.
08

Switch the Probe

Hold

for 3 seconds to switch Probe 1

or Probe 2, the sequence is PROBE1 ->

PROBE 2 in sequence.

æMeat Selection

Press the

button to select

the type of meat you want to cook.

çTaste Selection
Press the button to select the taste level of the meat you want to cook.

09

è Alert Function

Press

to turn on the alert function, the alert icon appears,

the sequence is Probe 1 ON – probe 2 ON – Probe 1 & Probe 2 ON –

Probe 1 & Probe 2 OFF.

When the alert function is ON, it will signal an alarm once it reaches the alert temperature, the alert icon will flash, the orange light will flash, probe 1 beeps for 1 second, and probe 2 beeps BIBI for 1 second. Once dual probe alert function is on, it will beep BI BI BI for 1 second.

NOTE: Some types of meat do not support all taste selection.

Meat Selection Each press will change the display in the following sequence:
BEEF LAMB VEAL HAMBURGER PORK TURKEY CHICKEN FISH PROGRAM
The different taste options:

The corresponding preset temperature will show on the monitor as “TEMP SET”.

10

11

æ When in time display mode, hold the button for 3 seconds,
will start to flash.
12

ç Press

and

to adjust the temperature setting
and press

to confirm the setting.

The setting mode will remain

without any operation in 30

seconds.

è Press

to turn On/Off

the alert function, the alert

icon appears, the sequence

is probe 1 ON – probe 2 ON –

probe 1 & probe 2 ON – probe

1 & probe 2 OFF.

é When the alert function is ON, it will signal an alarm once it reaches the alert temperature, the alert icon will flash, the orange light will flash, probe 1 beeps BI for 1 second, and probe 2 beeps BIBI for 1 second. Once the dual probe alert function is on, it will beep BI BI BI for 1 second.
ê To turn off the alarm, press any key to stop the beep soud. This turns the orange light OFF and the blue light ON for 10 seconds. After 5 minutes it will re-beep once the temperature goes higher than the target set temperature. If the temperature is always lower than the set temperature, it stops alerting.
To set probe 2 target temperature, press the for 3 seconds to switch probe 2, and repeat the first step.
NOTE: The temperature alarm function button
should be opened in the time display status (0:00).
13

4.2 Timing Mode
The count up and count down timer operates independently from the temperature sensor.

d

æ Hold

to switch time mode. The default is 00:00, the icon “:” flashes and ”

” appears.

ç Hold

for 3 seconds to set the time following the sequence:12/24H -> hour -> minute.

è When setting time, Press

for 3 seconds to go ahead to an 8 step/second speed.

Press for 3 seconds to go back in the 8 step/second speed.

é When setting time, the setting icon will flash.

æ Touch

to change

count up timer mode, the

default is 0H00M00S, icon

appears.

ç To start or stop the count up timer,

press the

button when 0:00:00

is dispalyed on the monitor.

14

15

Down

æ Touch

to change

count down timer mode,

the default is 0H00M00S,

the icon

appears.

ç Hold

for 3 seconds

to set the count down timer,

the sequence is in (hour minute – second)

è For settings, press to increase the setting and hold for 3 seconds to increase the setting for 8 steps; and press the button to decrease the setting and hold
for 3 seconds to decrease the setting for 8 steps

16

é Touch

to change

the minute or second

press

to increase

the setting and press

button to decrease

the setting.

ê Touch

to start

counting down.

Hold

and

at the same time

to clear the timer.

For count down mode, will display, the max count down timer
is 9:59:59.

When completing the count down timer , it BEEPS once, the orange light flashes and lasts for 30 seconds, press any key to stop the alarm.

17

If the temperature displayed seems to read too high or the temperature seems to increase too quickly, check to make sure the probe tip is not poking through the food. Re-position the probe tip in the center of the thickest part of the food. Avoid touching bone or heavy fat areas.
If the receiver and the transmitter display “LLL” or “HHH” instead of the probe temperature, wait for the probe to reach the current temperature. If “LLL” or “HHH” is still displayed or you get a false temperature, reinsert the probes into the transmitter and twist them back and forth so they make good contact.
Always turn off the devices after use to increase battery life. If the devices are not used for a long time, please remove the batteries.

Always wear a heat resistant glove when touching the stainless steel probe or heat resistant wire during, or just after cooking.
Hand wash the stainless steel probe thoroughly (probe is not dishwasher safe). Keep the stainless steel probe and heat resistant wire away from children.
If the meat temperature does not appear on the screen after the probe has been inserted into the meat, check to make sure the plug from the probe is securely inserted into the side of the transmitter.
Do not place the monitor in direct sunlight, or let it come in direct contact with moisture or hot surfaces. Do not use the pre-programmed thermometer in a microwave oven. Do not submerge the probe wire or plug in water. Moisture inside the probe’s plug or the thermometer might cause an incorrect temperature reading. Always wipe the probe’s plug before plugging it into the transmitter. Do not expose probe or probe wire to open flames or barbeque. Doing so can deteriorate the probe.

18

19

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void user’s warranty. Don’t expose probe or probe wire to open flames or barbeque. Dual probe can test two different meats at the same time. Use the metal holder to support the probe when in use on a BBQ. If using the probe lower than -20¥(-4) it will display “LLL”. If using the probe higher than 300¥(572) it will display “HHH”.
20

WARRANTY
BONUS! Get an extra 3-year warranty by sending your order # to support@innotruth.com.

30 DAYS FREE RETURN & REPLACEMENT

2-YEAR Product Warranty (If any problems with quality are found,
we will provide a free replacement.)

Lifetime Customer Support

Feel free to contact us if you have any problems! (for week days) (24/7)

21

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>