Brackenheath BR3511 LED Highbay Dimmable Plug In Option Instruction Manual
- June 4, 2024
- brackenheath
Table of Contents
BR3511 LED Highbay Dimmable Plug In Option
Instruction Manual
| BR3511 | 150W LED Highbay with Dimmable Plug-in Option 4000K |
|---|---|
| BR3512 | 150W LED Highbay with Dimmable Plug-in Option 6500K |
| BR3513 | 200W LED Highbay with Dimmable Plug-in Option 4000K |
| BR3514 | 150W LED Highbay with Dimmable Plug-in Option 6500K |
LED Highbay with Dimmable Plug-in Option
Features
- High efficiency LED replacement for tungsten halogen fittings
- Flicker free, integral driver incorporated into fitting
- Hanging loop with 2 meters of power flex supplied for ease of install
- Plug-in microwave sensor (BR3521) available with dimmable operation via remote control (BR3522). Both accessories sold separately
- 5-year guarantee
Dimensions
| Dimension | BR3511/BR3512 | BR3513/BR3514 |
|---|---|---|
| a. | 310.00mm | 360.00mm |
| b. | 40.00mm | 49.00mm |
| c. | 164.70mm | 173.20mm |
Safety Instructions
- These instructions should be read carefully and retained after installation for future reference and maintenance
- Ensure that the mains power is switched off before carrying out installation or maintenance
- This product should be installed by a qualified electrician ensuring the installation complies with the current edition of IET wiring regulations, BS 7671
- Ensure adequate free air ventilation is allowed around the light fitting. Do not cover with insulation
- The fitting can become hot with use. Allow adequate cooling time before handling
- Do not install this fitting where ambient temperature exceeds 45°C
- Ensure all electrical connections are secure and that there are no loose strands. This product is of class I construction and must be earthed
Environmental Instructions
This product may contain substances that can be hazardous to the environment
if not disposed of properly. Electrical and electronic equipment should never
be disposed of with general household waste but must be separated for its
correct treatment and recovery. Where possible recycle your packaging.
Installation Instructions
-
Switch off the electricity at the fuse box by removing the relevant fuse or switching off the circuit breaker before proceeding with the installation
-
This product must be installed using the anti-loosen nut and ring supplied. Find a suitable location to install the product and suspend using a sufficient hanging hook (see images below)
-
Connect the power cable to the electrical supply, ensuring correct polarity as follows:
– Brown to live (L)
– Blue to neutral (N)
– Green/Yellow to earth
The live conductor should be in-line with the circuit breaker and any isolation switches -
Switch on the power supply and check the light operates correctly
Note: Do not stare at the light source once product is illuminated
Maintenance Instructions
- There are no serviceable parts in this fitting.
- Periodically clean the housing and heat sinks to maintain adequate heat dissipation.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- This product contains a light source of energy efficiency class E to Regulation (EU No 2019/2015)
| Input Voltage | 220-240V 50Hz | CRI (Ra) | > 80 |
|---|---|---|---|
| Wattage | BR3511/BR3512 | 150W | Total Lumens |
| BR3513/BR3514 | 200W | BR3513/BR3514 | 26,000lm |
| Electrical Classification | Class I | Colour Temperature | BR3511/BR3513 |
| BR3512/BR3514 | 6500K | ||
| IP Rating | IP65 | Energy Efficiency Class | E |
| Operating Temperature | -20°C to +45°C | Life Hours (L70) | 50,000 Hrs |
Deta Electrical Company Limited
UK: Panattoni Park Luton Road Chalton Bedfordshire LU4 9TT
EU: Unit 16 Ashbourne Ind. Est. Ashbourne Co. Meath A84 W972 Ireland
deta.co.uk Technical Helpline: +44(0)1582 544 548