PowerA 1509988-03 Enhanced Wireless Controller User Manual

PowerA 1509988-03 Enhanced Wireless Controller User Manual

CONTENTS

• Enhanced Wireless Controller for Nintendo Switch™
• 10ft (3m) USB-C Charge Cable
• User Guide

Product Overview

SET UP

Check for system update. Nintendo Switch system update version 6.0.1 or later is required for use of PowerA Wireless controllers.

1. Connect your Nintendo Switch to the Internet
2. Typically, system updates will be downloaded automatically when connected online.
3. Select ‘System Settings’ from HOME menu, then scroll down to ‘System’ to see System Update version and automatically check for system update.
   For additional help, search ‘system update’ from Nintendo Support website.

RECHARGEABLE 900 MAH INTERNAL BATTERY

Controller was charged at the factory, but if top LED is flashing red, plug in USB cable to charge prior to initial pairing. Get up to 30 hours of game play when fully charged (other variables affect play time).
NOTE: Remember to charge controller at least once every 45-60 days (regardless of use) so battery retains ability to charge. Battery capacity will gradually reduce over time with repeated charging.

WIRELESS PAIRING

From the HOME Menu, select ‘Controllers,’ then ‘Change Grip and Order.’ While the following screen is displayed, press and hold down the SYNC Button for at least one second on the controller you wish to pair.
NOTE: After controller is paired once, it will auto connect next time.

UNDERSTANDING LED INDICATORS

1. The top LED near the USB port will flash Red when the internal battery is near depletion. Plug in USB cable to charge once indicator is flashing for uninterrupted game play. LED will turn solid red during charging, and off once fully charged.
2. The front LED (between Capture and Home buttons) indicates controller will flash during programming of Advanced Gaming Buttons.
3. The four LEDs on the bottom indicate Power & player number 1-8, and will cycle from left to right during wireless pairing

ASSIGNING ADVANCED GAMING BUTTONS

1. Press the Program Button on the bottom of the controller. The Advanced Gaming Button Program Status LED will flash, signaling the controller is in assign mode.

2. Press 1 of the following buttons (A/B/X/Y/L/R/ZL/ZR/
   Left Stick Press/Right Stick Press/D-pad) to re-assign. Then press the Advanced Gaming Button (AGR or AGL) that you wish to assign. The Advanced Gaming Button Program Status LED will stop flashing, signaling the Advanced Gaming Button has been set.

3. Repeat for the remaining Advanced Gaming Button.
   NOTE: Advanced Gaming Button assignments will remain in memory even after disconnected.

RESETTING ADVANCED GAMING BUTTONS

1. Hold the program button down for 2-3 seconds. The Advanced Gaming Button Program Status LED will slowly flash, signaling the controller is in program mode.
2. Press and hold the Assign Program Button for 5 seconds to reset to no function.

TROUBLESHOOTING

Q1. My Wireless Controller is not pairing.
A1. Confirm batteries are charged by plugging in USB-C cable.
A2. Confirm you are following the ‘Wireless Pairing’ process.
A3. Insert paper clip into Factory Reset Hole as marked above to reset controller to factory settings.
For latest FAQs, visit PowerA.com/Support

BATTERY WARNING

Don’t attempt to replace the rechargeable battery yourself – you may damage the battery, which could cause overheating, fire, and injury. The Lithium-ion battery in your device should be serviced or recycled by PowerA or an authorized provider and must be recycled or disposed of separately from household waste.
Dispose of batteries according to your local environment laws and guidelines.
Don’t use or leave the product containing recharegeable batteries exposed to very high temperatures (e.g. at strong direct sunlight or in a vehicle in extremely hot weather). Otherwise, it can overheat, catch fire, or the performance will degenerate, and the service life will be shortened.
Don’t use the rechargeable battery item in a location where static electricity is rich, otherwise, the internal safety devices may be damaged, causing a harmful situation.
In case the electrolyte gets into the eyes due to the leakage of battery, do not rub eyes. Rinse eyes with clean running water and seek medical attention immediately. Otherwise, it may injure eyes or cause a loss of sight.
If the battery gives off an odor, generates heat, or in any way appears abnormal during use, recharging or storage, immediately remove it from battery charger and place it in a contained vessel such as a metal box. Be aware discarded batteries may cause fire, do not heat the controller or throw it into fire.

MOTION WARNING

Playing video games can make your muscles, joints, skin or eyes hurt. Follow these instructions to avoid problems such as tendinitis, carpal tunnel syndrome, skin irritation or eyestrain:

• Avoid excessive play. Take a 10 to 15 minute break every hour, even if you don’t think you need it. Parents should monitor their children for appropriate play.
• If your hands, wrists, arms or eyes become tired or sore while playing, or if you feel symptoms such as tingling, numbness, burning or stiffness, stop and rest for several hours before playing again.
• If you continue to have any of the above symptoms or other discomfort during or after play, stop playing and see a doctor.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

CAN ICES-3(B)/NMB-3(B)

This device contains licence-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause interference;
2. This device must accept any interference, including interference that may cause undesired operation of the device

MANUFACTURED BY
Bensussen Deutsch & Associates, LLC. (BDA, LLC.)
15525 Woodinville-Redmond Rd. NE
Woodinville, WA 98072
BDAINC.com | POWERA.com

CONTACT/SUPPORT

For support with your authentic PowerA accessories,
please visit PowerA.com/Support.

Warranty

Two year limited warranty
For warranty details or support with your authentic PowerA accessories, please visit PowerA.com/Support.

AUSTRALIAN WARRANTY STATEMENT
This product comes with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitledto have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If purchased within Australia or New Zealand, this product comes with a One-year warranty from date of purchase. Defects in the product must have appeared within One year from date of purchase, in order to claim the warranty. All warranty claims must be facilitated back through the retailer of purchase in accordance with the retailer’s return policies and procedures. Any expenses incurred, as a result of returning the product to the retailer of purchase are the full responsibility of the consumer.

AU WHOLESALE DISTRIBUTOR
Level 2, 2 Darling Street South Yarra, Australia VIC 3141
bluemouth.com.au
Email: support@bluemouth.com.au
+61   (3) 9 8 67 2666

ADDITIONAL LEGAL
PowerA, and the PowerA logo are trademarks of Bensussen Deutsch and Associates, LLC. TM and © Bensussen Deutsch and Associates, LLC.
Nintendo Switch is a trademark of Nintendo. Licensed by Nintendo. All rights reserved.
All other trademarks are the property of their respective owners.

REGIONAL COMPLIANCE SYMBOLS
More information available via web-search of each symbol name.

The WEEE (Waste of electrical and electronic equipment) symbol requires battery disposal outside of other household waste per local regulations. Contact your city office, waste disposal service, or retailer for guidance.

CE (Conformité Européene aka European Conformity) is a certification mark that indicates conformity with health, safety, and environmental protection standards for products sold within the European Economic Area.

The Regulatory Compliance Mark is a visible indication of a product’s compliance with all applicable ACMA (Australian Communications and Media Authority) regulatory arrangements, including all technical and record-keeping requirements regarding the electrical safety and/or electromagnetic compatibility (EMC).

DECLARATION OF CONFORMITY
Hereby, Bensussen Deutsch & Associates LLC at 15525 Woodinville-Redmond Road NE, Woodinville, WA 98072 USA, declares that this wireless controller is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: PowerA.com/compliance

WIRELESS SPECIFICATIONS

1. Frequency Range: 2.4 – 2.4835GHz
2. Max E.I.R.P.: < 10dBm

Customer Service

PowerA.com/Support
BDA, LLC.
15525 Woodinville-Redmond Rd NE
Woodinville, WA 98072

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>