AXESS Single 6.5″ Portable Bluetooth Speaker PABT6028 User Manual
- June 6, 2024
- Axess
Table of Contents
AXESS Single 6.5″ Portable Bluetooth Speaker PABT6028 User Manual
TO CUSTOMERS
Thank you for your support and trust on purchasing the products of our company. To fully exert the function of the product, we suggest you to read the operating instruction carefully before using it, for the convenience of grasping the connection method and using points. Please take care of the operating instruction after reading it for the purpose of further reference.
SPECIFICATIONS
- Double 6.5″ speakers FM radio function
- 2x 3″ Tweeter 400Watt (PMPO) output power
- 10m bluetooth range 3000mAh battery capacity
- Brilliant led lights 7.4 Volt Boost
- TWS Link+ True Wireless Stereo DC 5V voltage
- TF card slot Frequency response: 150Hz -18Hz
- AUX and USB input
- Microphone input
Panel Buttons
MODE: Switching among the inputs and powering ON/OFF LED lights
- : Play the previous music under Bluetooth, TF card and USB mode, Play previous radio station under FM mode NI
- : Short press for music play/pause Long press for radio station automatic searching under FM mode •H
- : Play to next music under BT, TF and USB mode Play next radio station under FM mode
AUX: aux-in jack can connect the speaker to any PC, mp3, mobile phone,
etc
EQ: equalizer
USB Port: Support USB and can play MP3 and WAV format music in U disk
TF Card Port: support TF card and can play MP3 and WAV format music
MIC: plug-in for wired microphone
ECHO: microphone priority
LED Dial: master volume dial
OPERATING BLUETOOTH MODE
- After the power is turned ON, press the “MODE” button to enter into Bluetooth mode. Check to see if “Bluetooth” appear on the display screen to affirm you’re on the right mode.
- Turn on your mobile device and put it in Bluetooth mode, search for the device name “PABT6028” and confirm the connection when it appears
- Once the pairing is successfully, the speaker will emit beep tone
OPERATING AUX MODE
- Plug one end of the 3.5mm audio cable into the speaker’s AUX jack, and the other end to your mobile device (cellphone, laptop, tablet, etc)
- Control your music from the play/pause or forward/backward buttons on the speaker panel or directly from the mobile device.
OPERATING LED FUNCTION
- Press and hold ‘MODE’ button to turn ON or OFF the LED display lights
OPERATING TWS FUNCTION
- Begin by using your mobile device to succcessfully pair one of 2 bluetooth speakers on Bluetooth mode.
- When pairing is successfully, move onto the second speaker. Make sure that speaker #2 is on bluetooth mode as well and double click the “PLAY/PAUSE” button to turn on its TWS mode.
- If both speakers are close to each while pairing, they should quickly connect together and begin to play your music simultaneously.
CHARGING
- Take the USB charging cable and plug it into the DC 5V charging port. And charge it directly into a wall plug or into a computer USB port to charge
- To make sure your speaker is being charged, look for the charging indicator located on the right side of the LED screen. It will light up when charging and will stop lighting up when the speaker is fully charged.
NOTE: When speaker is not in use please turn off the device to conserve battery life. Make sure to turn down the volume when you turn off the device so you can maintain the speakers’ (sub)woofer in good condition. This way you are less like to burn out or damage the device.
ATTENTION!
FOR FIRST TIME USE FULLY CHARGE THE DEVICE UNTIL THE LIGHT INDICATOR TURNS
OFF AS INSTRUCTED IN THE MANUAL.
This can take up to approximately 8 hours to fully charge. If you don’t, the
device will not function at full capacity.
Axess Products Corporation
6649 Valjean Ave. Van Nuys, 91406 Tel.
818-785-4000 Fax.
818-785-5081
info@axessusa.com
Questions? Comments?
Contact us at support@axessusa.com
© 2018 Axess Products Corporation. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>