SECURITY BRANDS 14R300 300-MHz Transmitter Instructions
- June 6, 2024
- SECURITY BRANDS
Table of Contents
INSTRUCTIONS
300-MHz Transmitter
Model 14-R300
IN THE BOX
Make sure you have everything shown here. NOTE: The CR2032 battery comes pre- installed.
WHAT’S WHAT
The 300-MHz Transmitter has two programmable buttons and a status LED. Each button can be paired to a separate receiver or the same receiver.
SETUP
-
On your 300-MHz receiver, set DIP switches to desired positions.
NOTE: For best results, we recommend using the Security Brands Receiver 300 (14-REC300).
NOTE: By default, both sets of DIP switches on the 300-MHz Transmitter are matched to the default DIP switch positions of the Receiver 300 and other 300-MHz receivers. For security reasons, we recommend using custom DIP switch positions.
NOTE: Some DIP switches may be labeled to the position labeled 0 on the remote, and position labeled as OPEN. -
Open the 300-MHz Transmitter unit by removing two screws on the bottom side and pulling the case apart. Remove visor clip if needed for easier access.
NOTE: Make sure the circuit board stays attached to the base of the remote unit and does not come off with the cover. -
Find DIP switches on the 300-MHz Transmitter unit corresponding to the button you want to program.
NOTE: Pay attention to the markings on the circuit board showing which set of DIP switches corresponds to which button. -
Set DIP switches to match those set on the receiver.
-
Repeat the procedure for the second button if desired. Otherwise, close the unit and secure it with screws.
NOTE: The second button can be paired with the same or a different 300-MHz receiver.
HOW TO USE
- Make sure you are in the range of the 300-MHz receiver you want to control.
- Press the remote button linked to the desired receiver. The LED should light.
- The receiver will respond and operate the gate/door.
NOTE: If the receiver does not respond, make sure it has power and that
the remote LED is lighting when a button is pressed. If not, check the
battery. If the receiver still does not respond, make sure its antenna is not
inside a metal box, the DIP switch positions match on both remote and
receiver, and if it is a third-party receiver, make sure the frequency jumper
is in the 300-MHz position.
Two-Year Limited Warranty
Visit
securitybrandsinc.com/warranty/ for
details
WARNING! AUTOMATIC GATES CAN CAUSE SERIOUS INJURY OR DEATH! ALWAYS CHECK THAT THE GATE PATH IS CLEAR BEFORE OPERATING! REVERSING OR OTHER SAFETY DEVICES SHOULD ALWAYS BE USED!
FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
? NEED HELP
call 972-474-6390 or email
techsupport@securitybrandsinc.com
© 2021 Security Brands, Inc. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>