Chongqing Haizhimei Health Technology HZM-P001 Smart Visual Ultrasonic Tooth Cleaner Instruction Manual
- June 5, 2024
- Chongqing Haizhimei Health Technology
Table of Contents
Operation Instructions
for Smart Visual Ultrasonic Tooth Cleaner
Product introduction
Thank you for using our product. As a smart visual ultrasonic tooth cleaner, this product can realize real-time guidance, low latency, and high-definition display through a mobile phone connecting to application software, to meet your unknown experience of oral care, improve your oral health, and ensure a fresh breath.
Picture1
| No. | Name |
|---|---|
| 1 | Camera |
| 2 | Working tip |
| 3 | Body |
| 4 | Power button |
| 5 | Three modes |
| 6 | Inductive charging |
Charging
Please charge the smart visual oral irrigator for 8 hours before using it for the first time.
- Connect the charging base to the DC5V power supply at the output end of the mobile phone charger with a USB cable.
- Put the main body into the charging base for inductive charging.
Charging process: (picture)
Note: After
fully charged, the battery life of a smart visual tooth cleaner can be up to
200 minutes
Preparation for use
-
Use your mobile phone to scan the QR code to download the APP
(It supports Android4.0;iOS9.0 or above system)
http://ybxz.77z1.com/ -
opens the cell phone WLAN list and finds the same Wi-Fi name as the device name (such as the address at the beginning of the WLAN XXX Click or HZM xxx) to link
-
Click Download download installed APP to enter
-
Gototheoperationinterface,page1isthecompanyprofile,andpage2istheproductmall.
Chongqing haizhimei Health Technology Co.. Ltd. is a technology company that designs, produces, and sells oral health care products. With the competitive advantage of nursing visualization, we invent and create the internationally leading oral care technology to provide a full range of oral health care solutions for the oral health of the whole people. The service scope covers the design/development, manufacture rind sales of oral care products, HalzhImel has always adhered to market-oriented. centered on real health protection, relying on industry-leading technology and product research and development system, rich industry experience, and strong execution to provide an integrated visualization of the whole process of oral health and teeth whitening. The solution is to use technology and wisdom to improve the oral health of the whole people and create a better life. -
slides left to page 3 “Start link” and click the immediate link! Complete WIFI map link for device and phone.
| 
---|--- -
Install the working tip: Screw the working tip into the transducer shown in the picture, and lock it clockwise with a wrench.
-
One-button operation: Press and hold the “Power” button to turn on the device (picture)
Tip: You can press and hold for two seconds to turn on/off the device, and press to switch modes. -
Start to use: Observe the area requiring ultrasonic tooth cleaning through the mobile video, and press the “Power” button to switch to the mode you want, to effectively remove calculus, tartar, and dental stains.
Tip: No. 1 sharp working tip is suitable for removing tartar, and No. 2 flat working tip is suitable for removing tartar and dental stains.
Mode introduction and use
- Make sure that the smart visual ultrasonic tooth cleaner has been turned on. If it is turned off, please press and hold the button for 2 seconds and then release to turn on the product.
- You can change the mode by tapping the switch.
-“Soft” mode
* It provides a vibration frequency of 30KHZ to remove small tartars, which
is suitable for people who use it for the first time or people with sensitive
teeth.
“Standard” mode
It provides a vibration frequency of 35KHZ, to remove small or moderate
dental calculus
-“Strong” mode
It provides a vibration frequency of 40KHZ to effectively remove stubborn
massive calculus and tooth stains.
FAQ
-
What should I do if my gums are bleeding in the process of using this product?
Answer: Gum bleeding may be caused to people with periodontitis or gingivitis. If your gums are bleeding when using this product, please stop using it and rinse your mouth with cold water. -
Is it normal that the working tip for cleaning teeth gets hot during use?
Answer: It is normal for the temperature of tooth cleaner to increase slightly because the transducer will convert electrical energy into kinetic energy during use. -
Is it normal that the product suddenly stops working when it is working ultrasonically?
Answer: The product is equipped with an automatic shut-off function, so it will stop working after the transducer has been working for 10 minutes, and you need to switch the mode again to start working. -
What should I do if the product does not work normally?
Solution: Please charge the battery continuously for more than 3 hours to activate the battery when the battery power is insufficient after purchase or has not been used for a long time -
What should I do if there is no screen after the mobile phone is connected to the software?
Solution: Please check whether it is connected to the corresponding wireless network of the product -
Does the product have a warranty period?
Solution: Yes. It is promised that this product enjoys a one-year warranty for non-artificial quality problems. Please rest assured to buy.
Product parameter Product name| Smart visual tooth cleaner| Product model| HZM-P001-01
---|---|---|---
Operating temperature| -10–50°C| Operating voltage| DC 3.7V
Battery| 1800mAh| Input voltage| DCSV
---|---|---|---
Battery life| Approximately 200 minutes| interior input power| 2W
Charging time| 8h| Waterproof level| IPX7
Charging mode| Inductive charging| Executive standard| GS4706.1/59
Image transmission rate| 300Mbps| Camera pixels| 5 mega-pixel
Network standards| IEEE 802.11b/g/n
Product dimensions| 30*200mm
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction