DENSO BHT-M70 Series BHT-M60 Hand-Held Terminals User Guide
- June 6, 2024
- DENSO
Table of Contents
SAFETY PRECAUTIONS
BHT-M70 Series
Please read this manual thoroughly prior to operation to ensure full use of the product’s functionality, and store safely in a convenient location for quick reference even after reading.
496996-0940
SAFETY PRECAUTIONS
Be sure to observe all these safety precautions. Meaning of Symbols
DANGER Alerts you to those conditions that could imminently lead to
serious bodily injury or death if the instructions are not followed correctly.
WARNING Alerts you to those conditions which could cause serious bodily
injury or death if the instructions are not followed correctly.
CAUTION Alerts you to those conditions which could cause minor bodily
injury or substantial property damage if the instructions are not followed
correctly.
DANGER
Handling battery
Failure to follow all instructions listed below may cause electrical shock,
overheating, smoking, fire, or an explosion.
- Never disassemble or modify the battery.
- Do not stick a needle into the battery, hammer at it, or tread on it.
- Avoid dropping or throwing the battery or letting it undergo any shock or impact. Do not use significantly damaged or deformed batteries. Do not use batteries when they are subject to the impact, for example, a drop impact.
- Never connect the positive and negative terminals of the battery with a wire or other metallic materials.
- Do not carry or store the battery together with ballpoint pens, necklaces, coins, hairpins, or anything else metallic. Never place the battery into or soak it in water or seawater.
- Never burn or heat up the battery.
- Do not use or leave the battery in places where there is excessively high temperature (60 C or higher) such as near fire or heater. Do not use or store the battery in places exceeding the service or storage temperature.
- Never charge the battery near a fire or in strong sunlight. Raised battery temperature may result in leakage of battery fluid, blowout, or combustion.
- Never charge or use the battery where any inflammable gases may be emitted. Never apply solder directly to the battery. Do not use batteries other than the specified ones.
- If the battery fluid leaking from the battery gets into the eyes, wash thoroughly with clean water such as tap water without rubbing and obtain medical treatment immediately.
- Failure to do so will result in eye injuries. .
- During use, charging, or storage of the battery, if odors come from the battery, the battery is overheated, discolored, deformed, or anything unusual is found, unload the battery from the BHT or charger. Do not use the battery.
- If the battery does not finish recharging within the specified time, stop recharging.
WARNING
Handling the BHT
Incorrect handling of the BHT could cause electric shock, impaired vision,
skin problems, injury, burns, and the generation of heat and smoke from the
BHT. Be sure to observe the following to use the device correctly.
-
Never disassemble or modify the BHT.
-
When the BHT is subject to a strong impact, for example, a drop impact, check the case for any damage and the battery for damage and leakage.
Never use a damaged case.
Never use a damaged or leaked battery. -
Do not insert any foreign materials into the battery cartridge.
-
Do not get the BHT wet or put it in water or seawater. Never put the BHT in a microwave oven or high-pressure container. Never put it on the induction cooktop.
-
Never put the BHT in places where there are excessively high temperatures, such as inside closed-up automobiles, or in places exposed to direct sunlight.
-
Avoid using the BHT in extremely humid or dusty areas, or where there are drastic temperature changes.
-
If smoke, abnormal odor or noise comes from the BHT, immediately turn off the power and remove the battery cartridge from the scanner case.
-
If the LCD screen is broken by mistake, care must be taken not to get the liquid crystal into your eyes or mouth or drop it on your skin. Be careful of broken glass if the LCD screen is accidentally cracked or broken. It may cause bodily injury.
-
If the LCD screen is accidentally broken and liquid crystal gets into your eyes or mouth, wash it off immediately with clean water and then seek medical care. Never stare into the reading window.
Handling battery
Failure to follow all instructions listed below may cause electrical shock,
overheating, smoking, fire, or an explosion.
-
The battery is exclusively for the BHT. Do not use the battery for purposes other than charging the
BHT. -
To charge the battery, be sure to use the specified charger, the charging cable, or the recommended wireless charger.
-
If abnormal odor, heat, discoloration, deformation or any other abnormal conditions are noticed when the battery is in use, being charged, or is in storage, remove it from the BHT or charger and avoid further use.
Handling the scanner using a laser light
The 2D Code Handy Terminal uses laser light for indicating the scanning range.
The intensity of the laser light is too low to inflict bodily injury. However,
do not stare into the beam.
You must observe the following precautions when handling the BHT equipped with
laser light.
- Never stare into the reading window.
- Never point the reading window at someone’s eye. Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019.
[BHT-M70 series]
- LASER LIGHT-DO NOT STARE INTO THE BEAM.CLASS 2 LASER PRODUCT.
- LUMIERE LASER- NE PAS REGARDER DANS LE FAISCEAU. APPAREL LASER DECLASS
- Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed.3, as described in Laser Notice No.56, dated May 8, 2019.
To System Designers
- When introducing BHTs in those systems that could affect human lives, develop applications carefully through redundancy and safety design which avoids the feasibility of affecting human lives even if a data error occurs.
CAUTION
Handling the BHT
Incorrect handling of the BHT could cause the generation of heat and smoke
from the BHT, and malfunction. Be sure to observe the following to use the
device correctly.
- When using the hand strap or neck strap, exercise due care to avoid getting them caught in other objects or entangled in rotating machinery. Failure to do so could result in an accident or injury.
- Keep your ears away from the speaker when a loud sound comes out of it. Failure to do so could lead to hearing difficulty.
- Do not operate the BHT in environments where static electricity can build into significant changes. Doing so could result in malfunction or mechanical failure. Avoid dropping the battery cartridge or letting it undergo any strong shock or impact.
- Doing so could result in malfunction or mechanical failure. Do not use the BHT near a wireless transmitter such as a ham radio. Doing so could result in malfunction or mechanical failure.
- Do not touch BHT with oily hands or gloves containing oil such as machine oil and grease. Doing so may cause the deformation and discoloration of a device.
- This product incorporates connectors for microSD card and SIM cards. Do not insert anything other than these cards. Do not insert a card inversely, diagonally and with twisted. If a card is inserted forcibly, this could damage a card or a connector.
- Do not attach a wet BHT or rechargeable battery cartridge to CU.
- Do not use excessive force when inserting or removing the battery cartridge. Doing so could result in malfunction or mechanical failure.
- Keep magnetic cards such as a cash card or a credit card away from the BHT. Failure to do so could cause loss of magnetic data.
- Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Chapter 1 Please read me first
Please contact your nearest distributor, if using in other countries. The latest precision manufacturing technology yields LCD panels with an effective resolution of 99.99% or higher. The downside, however, is that up to 0.01% of the pixels can remain permanently dark or lit on today’s state-of-the-art panels. Furthermore, please be aware that individual differences may occur in the screen color and brightness due to the characteristics of the white LEDs used in the LCD display backlight. The Customer shall not modify, reverse compile, reverse engineer, reverse assemble, and or otherwise tamper with our BHT’s firmware.
About This Manual
Due to changes and improvements, the content of this manual may be subject to change without prior notice. The reproduction or duplication of the whole or part of this manual is strictly prohibited without prior consent. Please contact DENSO WAVE if this manual is lost. Every attempt has been made to ensure that the content of this manual is thorough and up to date, however, we kindly ask you to report any questionable descriptions, mistakes or omissions, if any, to DENSO WAVE.
Liability Limitations
DENSO WAVE INCORPORATED (“DENSO WAVE”) does not assume any product liability
(including damages for lost profits, interruption of operations, or the loss
of business-related information) arising out of, or in connection with, the
use of, or inability to use the BHT system software or related manuals. DENSO
WAVE takes reasonable precautions to ensure its products do not infringe upon
any patents or other intellectual property rights of other(s), however, DENSO
WAVE cannot be responsible for any patent or other intellectual property right
infringement(s) or violation(s) arising from any of the following.
(1) The use of DENSO WAVE’s products in connection or in combination with
other components, products, devices, data processing systems or software not
supplied by DENSO WAVE.
(2) The use of DENSO WAVE’s products in a manner for which they were not
intended nor designed. (3) The modification of DENSO WAVE’s products by
parties other than DENSO WAVE. If it is judged by DENSO WAVE that malfunction
of the product is due to the product having been dropped or subjected to
impact, repairs will be made at a reasonable charge even within the warranty
period. DENSO WAVE will not bear any responsibility for data that customers
have recorded and are received by DENSO WAVE for repair and analysis.
Free/Open source software (FOSS)
This product contains Free / Open Source Software (FOSS.) DENSO WAVE is ready to provide compliant source codes. For details, please contact our dealer or contact the site below. https://www.denso-wave.com/
Chapter 2 States Regulations
Declaration of Conformity for EU
Hereby, DENSO WAVE INCORPORATED declares that the radio equipment type BHT-
M70 is in compliance with Directive 2014/53/EU. BG DENSO WAVE INCORPORATED,
BHT- M70 2014/53/.
https://www.denso-wave.com/en/adcd/download/category/document/
| Application | Frequency Range | Power |
|---|---|---|
| HF RFID | 13.553 — 13.567 MHz | 60 dBpA/m at 10 in |
| Bluetooth | 2402 — 2480 MHz | 2.5 mW |
| Wireless LAN (11 b/g/n) | 2400 — 2485 MHz | 100 mW e.i.r.p. |
| Wireless LAN (11a/n) | 5150 — 5250 MHz (W52: 5.2 GHz Range) |
5250 — 5350 MHz (W53: 5.3 GHz Range)
5470 — 5725 MHz (W56: 5.6 GHz Range)| W52: 200 mW e.i.r.p.
W53: 200 mW e.i.r.p. W56: 1000 mW e.i.r.p.
Mobile Phones (GSM)| 873 — 915 MHz (ER-GSM 900)
876 — 915 MHz (R-GSM 900)
880 — 915 MHz (E-GSM 900)
890 — 915 MHz (P-GSM 900)
1710 — 1785 MHz (DCS 1800)| 2 W 2 W 2 W 2 W 1 W
Mobile Phones (W-CDMA)| 1920 — 1980 MHz (Band 1)
880 — 915 MHz (Band 8)| 250 mW
Mobile Phones (FDD-LTE)| 1920 — 1980 MHz (Band 1)
1710 — 1785 MHz (Band 3)
2500 — 2570 MHz (Band 7)
880 — 915 MHz (Band 8)
832 — 862 MHz (Band 20)| 200 mW
VIETNAM: RoHS
Complying with “CIRCULAR, No.30/2011/TT-BCT (Hanoi, August 10, 2011),
Temporary regulations on the content limit for certain hazardous substances in
electrical products”
For Australia
The BHT-M70 contains Wireless LAN and Bluetooth®.
RCM marking
Declaration of Conformity (for UK)
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC CAUTION
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter. The available scientific evidence does not show
that any health problems are associated with using low-power wireless devices.
There is no proof, however, that these low-power wireless devices are
absolutely safe. Low power Wireless devices emit low levels of radiofrequency
energy (RF) in the microwave range while being used. Whereas high levels of RF
can produce health effects (by heating tissue), exposure to low-level RF that
does not produce heating effects causes no known adverse health effects. Many
studies of low-level RF exposures have not found any biological effects. Some
studies have suggested that some biological effects might occur, but such
findings have not been confirmed by additional research. This Handy Terminal
has been tested and found to comply with FCC radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio frequency
(RF)Exposure Guidelines.
This device meets all the other requirements specified in Part 15E, Section
15.407 of the FCC Rules.
FOR PORTABLE DEVICE USAGE (<20 cm from body/SAR needed) The product complies
with the FCC portable RF exposure limit set forth for an uncontrolled
environment and is safe for intended operation as described in this manual.
The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power
if such function is available. For body-worn operating conditions please use
belt clips, holsters, and/or accessories that have no metallic component in
the assembly and must provide at least 10 mm for BHT-M70-QWG or 10 mm for
BHT-M70-QW separation between the device and the user’s body. Body-worn
accessories that do not meet these requirements may not comply with RF
exposure requirements and should be avoided FOR COUNTRY CODE SELECTION USAGE
(WLAN DEVICES) Note: The country code selection is for non-US model only and
is not available to all US models. Per FCC regulation, all WiFi products
marketed in US must be fixed to US operation channels only.
User Steps to Access Information
Starting from Menu or Home:
Step 1 BHTShell
Step 2 5 SystemInfo
Step 3 2 Regulatory Info
IC Regulation (for Canada)
Industry Canada statement: This device complies with ISED’s license-exempt
RSS. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution : (i) the device for operation in the band 5150-5250 MHz is only
for indoor use to reduce the potential for harmful interference to co-channel
mobile satellite systems; (ii) where applicable, antenna type(s), antenna
models(s), and worst-case tilt angle(s) necessary to remain compliant with the
e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be
clearly indicated.
Radiation Exposure Statement: The product complies with the Canada
portable RF exposure limit set forth for an uncontrolled environment and is
safe for intended operation as described in this manual. The further RF
exposure reduction can be achieved if the product can be kept as far as
possible from the user body or set the device to lower output power if such
function is available.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 10 mm for BHT-M70-QWG
or 10 mm for BHT-M70-QW must be maintained between the user’s body and the
handset, including the antenna. Third-party belt clips, holsters, and similar
accessories used by this device should not contain any metallic components.
Body-worn accessories that do not meet these requirements may not comply with
RF exposure requirements and should be avoided. User Steps to Access
Information
Starting from Menu or Home:
Step 1 BHTShell
Step 2 “5 SystemInfo”
Step 3 “2 Regulatory Info”
E-Waste for India
This product complies with e-waste (Management and Handling) Rules, 2011.
IMDA Regulation (for Singapore)
IMDA Compliance Marking
Complies with IMDA Standards
DB104459
THIS DEVICE MEETS INTERNATIONAL GUIDELINES FOR EXPOSURE TO RADIO WAVES Your
mobile device is a radio transmitter and receiver. It is designed not to
exceed the limits for exposure to radio waves (radiofrequency electromagnetic
fields) recommended by international guidelines. The guidelines were developed
by an independent scientific organization (ICNIRP) and include a substantial
safety margin designed to assure the safety of all persons, regardless of age
and health.
The radio wave exposure guidelines use a unit of measurement known as the
Specific Absorption Rate or SAR. The SAR limit for mobile devices is 2 W/kg.
Tests for SAR are conducted using standard operating positions with the device
transmitting at its highest certified power level in all tested frequency
bands. The highest SAR values under the ICNIRP guidelines for this device
model are:
Head SAR: 0.57 W/Kg
Body SAR: 1.74 W/Kg
During use, the actual SAR values for this device are usually well below the
values stated above. This is because, for purposes of system efficiency and to
minimize interference on the network, the operating power of your mobile
device is automatically decreased when full power is not needed for the call.
The lower the power output of the device, the lower its SAR value. Body-worn
SAR testing has been carried out at a separation distance of 0.5 cm. To meet
RF exposure guidelines during body-worn operation, the device should be
positioned at least this distance away from the body.
Organizations such as the World Health Organization and the US Food and Drug
Administration have suggested that if people are concerned and want to reduce
their exposure, they could use a hands-free accessory to keep the wireless
device away from the head and body during use or reduce the amount of time
spent using the device.
Note: The maximum SAR value listed above is the value recorded for the
latest version of this handset. Earlier versions may have different measured
SAR values, which are detailed in the User Manuals that accompany those
handsets.
NBTC regulation (for Thailand)
This telecommunication equipment is in compliance with NBTC requirements.
[BHT-M70-QW] (Specific Absorption Rate – SAR) 0.70 W/kg
This radiocommunication equipment has a specific absorption rate (SAR) of 0.70
W/kg as related to the equipment, which is in compliance with the Safety
Standard for the Use of Radio communication Equipment on Human Health
announced by the National Telecommunications Commission.
[BHT-M70-QWG] (Specific Absorption Rate – SAR) 1.74 W/kg
This radiocommunication equipment has a specific absorption rate (SAR) of 1.74
W/kg as related to the equipment, which is in compliance with the Safety
Standard for the Use of Radio communication Equipment on Human Health
announced by the National Telecommunications Commission.
Battery Request
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Rechargeable batteries contain scarce, valuable recyclable resources. We
kindly ask for your cooperation in recycling to promote the reuse of these
resources.
The crossed-out wheeled bin is applicable for EU member states only.
Used rechargeable batteries must not be disposed of as combustibles.
Contact your nearest battery recycling center or local sales office for
information on disposal procedures.
Never disassemble or break down rechargeable batteries.
- All rights reserved. No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher. All products and company names mentioned are trademarks or registered trademarks of their respective holders.
- DENSO WAVE INCORPORATED does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
- If it is judged by DENSO WAVE INCORPORATED that malfunction of the product is due to the product having been dropped or subjected to impact, repairs will be made at a reasonable charge even within the warranty period.
- Intellectual Property Precaution
DENSO WAVE INCORPORATED (“DENSO WAVE”) takes reasonable precautions to ensure its products do not infringe upon any patent of other intellectual property rights of other(s), but DENSO WAVE cannot be responsible for any patent or other intellectual property right infringement(s) or violation(s) which arise from (i) the use of DENSO WAVEs product(s) in connection or in combination with another component (s), product(s), data processing system(s) or equipment or software not supplied from DENSO WAVE; (ii) the use of DENSO WAVEs products in a manner for which the same was not intended nor designed; or (iii) any modification of DENSO WAVEs products by other(s) than DENSO WAVE.
Copyright © DENSO WAVE INCORPORATED, 2018
All rights reserved. No part of this publication may be reproduced in any form
or by any means without permission in writing from the publisher. All products
and company names mentioned in this document are trademarks or registered
trademarks of their respective holders. QB direct is a trademark of DENSO WAVE
INCORPORATED. AndroidTM is a trademark of Google LLC. Other products and
company names mentioned in this document are trademarks or registered
trademarks of their respective holders. Specifications are subject to change
without prior notice.
DENSO WAVE INCORPORATED
1 Yoshiike Kusagi Agui-Cho, Chita-gun, Aichi 470-2297, Japan
https://www.denso-wave.com/
This manual uses recycled paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>