Schneider Electric MTN6725-0101 SpaceLogic KNX DALI Gateway Instructions
- June 9, 2024
- Schneider Electric
Table of Contents
Schneider Electric MTN6725-0101 SpaceLogic KNX DALI Gateway
About this document
- You can find all the information required for safe installation in this document.
- More detailed product information is available on the Internet – > See QR code.
- http://go2se.com/ret-MTN6725-0101
For your safety
- DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
- Safe electrical installation must be carried out only by skilled professionals. Skilled professionals must prove profound knowledge in the following areas:
- Connecting to installation networks
- Connecting several electrical devices
- Laying electric cables
- Connecting and establishing KNX networks
- Safety standards, local wiring rules and regulations
- Failure to follow these instructions will result in death or serious injury.
Getting to know the device
-
The SpaceLogic KNX DALI Gateway Pro (hereinafter referred to as Gateway) is a multi-master application controller for controlling ECGs (electronic control gears) with
DALI interface via KNX. -
The Gateway supports DALI-1 and DALI-2 ECGs as well as DALI-2 motion detectors and light sensors. The Gateway has a DALI output that can be used to control 64
-
ECGs. In addition, up to 8 DALI-2 motion detectors or light sensors can be connected.
-
The required power for the connected ECGs and motion detectors is supplied directly from the device. Additional
-
DALI power supplies are not required.
-
The ECGs can be controlled in 16 groups per Gateway.
-
Beyond this, individual control of up to 64 ECGs is possible.
-
Besides controlling all standard control gear, the Gateway also allows the operation of single-battery emergency lighting (EN 62386-202). Emergency lighting systems
with a central battery are also supported. -
When using sensors supplied via the DALI bus, the power consumption of all DALI devices must not exceed the guaranteed value.
Connections and operating elements
- A KNX bus connection terminal
- B Error-LED
- C Ethernet-LNK-LED
- D Mains connection
- E RJ-45 socket
- F Display
- G Operating/programming buttons
- H DALI output terminals
- I Programming button
- J Programming LED
Installation and connection
installing
- WARNING Risk of death from electric shock.
- Only install devices with at least basic insulation next to the device.
- Failure to observe this instruction can result in death or serious injury.
- WARNING Risk of death from electric shock. The device can be damaged.
- Safety clearance must be guaranteed in accordance with IEC 60664-1.
- There must be at least 4 mm between the individual cores of the 230 V supply cable and the KNX line A
Connecting
- Operating voltage: AC/CDC 100-240 V, 50- 60 Hz
- Power consumption: max. 8 W
- Power supply from KNX: DC 24 V (SELV), approx. 5 mA KNX
- KNX Medium: Twisted Pair
- Security: KNX Data Secure Ready DALI
- Outputs: 1 Output D+/DType: Multi-master application
- controller
- Number of ECGs: max. 64 (DALI-1, DALI-2)
- Number of sensors: max. 8 (DALI-2)
- DALI voltage: typical DC 18 V, short-circuit proof, max 250 mA, basic insulation (no SELV)
- Power supply current: max. 250 mA, guaranteed: 160 mA
- Shutdown delay: 600 ms after DALI short-circuit
- Start-up attempt after
- shutdown: 5 s after short-circuit detection
- Ethernet
- Type: 100BaseT (100 Mbit/s)
- Supports: IEEE 802.3
- IP protection rating: IP20
- Protection class: I
- Overvoltage category: III
- Degree of contamination: 2
Environment
- The temperature in operation: -5 °C … +45 °C
- Relative humidity (noncondensing): 5% to 95%
- Device width: 4 TE = approx. 72 mm
- Dispose of the device separately from household waste at an official collection point. Professional recycling protects people and the
environment against potential negative effects
Schneider Electric -Contact
- Schneider Electric Industries SAS
- 35 rue Joseph Monier
- Rueil Malmaison 92500
- France
- If you have technical questions, please contact the Customer Care Centre in your country. se.com/contact
- UK Representative
- Schneider Electric Limited
- Stafford Park 5
- Telford. TF3 3 BL. Uk
RU Complies with technical regulations ≪O safety of low voltage equipment≫, ≪On electromagnetic compatibility≫ Date of manufacture: see general packaging: year /a week /weekday A country – manufacturer: Germany Shelf life: 3 years Warranty period: 18 months If a malfunction is detected during the warranty period and after its completion address to the regional Help Center Schneider Electric customers. Authorized Supplier in RF: JSC “Schneider Electric” Address: 127018, Russia, Moscow city, st. Dvintsev, 12, building 1 Tel. +7 (495) 777 99 90 Fax +7 (495) 777 99 92 se.com/ru/ru/
Documents / Resources
|
Schneider Electric MTN6725-0101 SpaceLogic KNX DALI
Gateway
[pdf] Instructions
MTN6725-0101, SpaceLogic KNX DALI Gateway, KNX DALI Gateway, SpaceLogic DALI
Gateway, DALI Gateway, Gateway
---|---
References
- Go2SE
- Contact Support | Schneider Electric Global
- Schneider Electric Казахстан | Мировой эксперт в управлении энергией и автоматизации
- Систэм Электрик - официальный сайт
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>