ASAHI DENSO ZKM013-903 Handsfree System User Manual

June 6, 2024
ASAHI DENSO

User Manual
Handsfree-System

Models : ZKM013
ZKM013A
ZKM013-903
ZKM013A-903

The document hereon is the property of Asahi Denso Co., Ltd.
ZKM013-820_0

Revision history

Rev. Date Points modified Changes description
00 20. Oct.2020 First Release
01 9. Nov.2020 Modify FCC ID (3.2.4)

Replace NCC disclaimer (3.2.8)
02| 17. Dec.2020| | 3.2.4 Change product name Steering lock ⇒ Ignition SW
3.2.5 Change product name Steering lock ⇒ Ignition SW
Add Vietnam certification
1. Add and change the sentence

Overview

This product is a steering lock with Handsfree-System designed to prevent theft.
This product can be attached to the motorcycle.

The system is composed of:

– The Ignition SW (1) with its integral steering lock equipped control unit (4), which provides the following functions:

  • User recognizer, by means of a Smart key (2) or an Immobilizer Key (3).
  • Lock and Unlock the steering, by moving the Lock bar (5).
  • Enable and disable the ignition of the bike.

– The Smart key (2) is referred to as Active Transponder. It can also be used as an Immobilizer key.
– The Immobilizer key (3) is referred to as Passive Transponder.
The Handsfree-System combines the LF: Low Frequency and the RF: Radio Frequency to recognize the right use of the motorcycle.
The system is integrated into the CAN bus for all data transfer with the other electronic units on the motorcycle.

Motorcycle start (Turn on the ignition and start the engine)

Smart key

User recognition with the Smart key (2) is performed as described below:

A. Press the knob on the Ignition SW (1).
B. The Control unit (4) installed on the Ignition SW (1) requires the Smart key (2) for a radio frequency identification with an LF signal transmitted by the LF antenna incorporated in the Control unit (4).
C. If the Smart key (2) is within a range of 1.0 m from the vehicle and the battery is adequately charged, replies to the Control unit (4) and starts authentication.
D. After successful authentication, the Ignition switch knob becomes rotatable for 5 seconds. While the knob is rotatable, LED (6) is lit. When the knob is rotated to the ON position, the main power of the vehicle turns ON and the engine can be started. If authentication failed, the engine can’t be started.
E. Press the starter switch on the handle switch to start the engine.

Immobilizer key
User recognition with the Immobilizer key (3) is performed as described below:

A. Press the knob on the Ignition SW (1).
B. After about 3 seconds, the control unit (4) installed on the Ignition SW (1) requires the Immobilizer key (3) for a low-frequency identification with an LF signal transmitted by the LF antenna incorporated in the Control unit (4).
C. If the Immobilizer key (3) is near the LF Antenna in the Control unit (4), reply to the Control unit (4) and start authentication.
D. After successful authentication, the Ignition switch knob becomes rotatable for 5 seconds. While the knob is rotatable, LED (6) is lit. When the knob is rotated to the ON position, the main power of the vehicle turns ON and the engine can be started. If authentication failed, the engine can’t be started.
E. Press the starter switch on the handle switch to start the engine.

Turn off the ignition and stop the engine

When the ignition switch knob is rotated to the OFF position, the main power of the vehicle turns OFF.
Neither Smart key (2) nor Immobilizer key (3) is required for Key OFF

Parking (Lock of the steering)

To lock the steering lock:
Stop the motorcycle, then put it on the side stand and steer the handlebar rightward or leftward to the lockable position.

Smart key
User recognition with the Smart key (2) is performed as described below:

A. A. Press the knob on the Ignition SW (1).
B. The Control unit (4) installed on the Ignition SW (1) requires the Smart key (2) for a radio frequency identification with an LF signal transmitted by the LF antenna incorporated in the Control unit (4).
C. If the Smart key (2) is within a range of 1.0 m from the vehicle and the battery is adequately charged, replies to the Control unit (4) and starts authentication.
D. After successful authentication, the Ignition switch knob becomes rotatable for 5 seconds. While the knob is rotatable, LED (6) is lit. When the knob is kept pressed and rotated to the LOCK position, the steering becomes locked.

Immobilizer key
User recognition with the Immobilizer key (3) is performed as described below:

A. Press the knob on the Ignition SW (1).
B. After about 3 seconds, the control unit (4) installed on the Ignition SW (1) requires the Immobilizer key (3) for a low-frequency identification with an LF signal transmitted by the LF antenna incorporated in the Control unit (4).
C. If the Immobilizer key (3) is near the LF Antenna in the Control unit (4), reply to the Control unit (4) and start authentication.
D. After successful authentication, the Ignition switch knob becomes rotatable for 5 seconds. While the knob is rotatable, LED (6) is lit. When the knob is kept pressed and rotated to the LOCK position, the steering becomes locked.

Replacing the battery in the Smart Key

[Important]

Take special care (A) when removing the key battery.
This symbol (B) warns the user about important use and maintenance instructions contained inside the documents provided with the equipment.

[Warnings / Caution]

Risk of battery leakage, heat generation, and explosion

  • Do not expose the key to high temperatures, such as on the dashboard, and under direct sunlight.
  • Do not mechanically crush or cut the key.

Risk of explosion if the battery is replaced by an incorrect type

  • Always use only the same or an equivalent type of CR2032 3.0 [V] coin batteries.

Do not include a coin battery in your mouth. There is a risk of burns from chemical substances.

  •  This product contains a coin battery.

  •  If coin batteries are accidentally ingested, chemical burns, penetration of mucosal tissue, etc.
    or in the worst case, death may result in just 2 hours.

  • Keep new and used batteries away from children.

  • If the battery cover does not close securely, stop using the product and keep it away from children.

  • If you suspect that a battery is might have been swallowed or placed inside any part of the body, seek immediate medical attention.

  1. Insert ②”screwdriver” into the dent of ①”Rear plastic cover”.
    Raise the inserted ②” screwdriver” in the direction of the arrow and remove ①”Rear plastic cover”.

  2. Insert ②”screwdriver” into the dent in ③”Coin battery cover”.
    Raise the inserted ②” screwdriver” in the direction of the arrow and remove ③”Coin battery cover”.

  3. Remove ⑤”Used coin battery” and replace it with ⑥”New coin battery” .

  4. Attach ③”Coin battery cover”.

  5. Attach ①”Rear plastic cover” with hooks in the order of (A) → (B).

Installation notes

Handsfree-System attachment

Handsfree-System consists of Ignition SW, Smart key, Immobilizer key.
These are attached to a vehicle by factory/field personnel.

Access to Smart key internal parts

It is strictly forbidden to have access to the inner electrical components, except the used battery to be replaced.

Product modifications

It is strictly forbidden to modify or tamper products included in the Handsfree System including the Antenna Unit.

If the product fails

All damaged components must be replaced.

Certification

Manufacturer
Company Name ASAHI DENSO CO., LTD.
Address 6-2-1 Somejidai, Hamakita-ku, Hamamatsu, Shizuoka 434-0046, Japan
Website http://www.ad-asahidenso.co.jp 
Approval of each country
Australia certification
China precautions for use
EU DoC

Ignitin SW
Smart key

3.2.4. FCC(USA) certification
Product name Ignition SW Smart key
FCC ID T8VZKM013A T8VZKM013A903

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.


3.2.5. ISED(Canada) certification
Product name Ignition SW Smart key
IC 6505A-ZKM013A 6505A-ZKM013A903

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1.  This device may not cause interference.
2.  This device must accept any interference, including interference that may cause undesired operation of the device.


Taiwan certification
Thailand certification
Vietnam certification

The certification mark is shown here because there is not enough space on the product to display the certification mark.

Kawasaki Motors
ViệtNam
B00162020

The document hereon is the property of Asahi Denso Co., Ltd.
ZKM013-820_0

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals