DENSO TN0020A Car Audio User Manual
- June 5, 2024
- DENSO
Table of Contents
DENSO TN0020A Car Audio
Model name | Car Audio |
---|---|
Model No | TN0020A |
Index Page
- Rating 2P
- Button Function Spec 3P
- Radio operation procedure 4P
- Operating manual (Bluetooth/Handsfree) 5P
- FCC Operating manual Requirement 6P
Rating
RATED VOLTAGE | 12.0V (10.5~16.0V) – ground |
---|---|
LOAD IMPEDANCE | 4Ω |
BACK UP CURRENT | 2.1mA or less |
RATED CURRENT | 4.0A or less (Vcc=13.2V, 0.5W output) |
AM TUNING RANGE | 530 – 1625 kHz (5kHz step) |
FM TUNING RANGE | 87.5 – 108 MHz (100kHz step) |
Button Function Spec
Button No. | Button Name | Operation |
---|---|---|
① | VOL UP | Short Push: Increase Volume Up 1 step Long Push: Increase Volume Up |
continuously
②| VOL DOWN| Short Push: Decrease Volume Down 1 step Long Push: Decrease
Volume Down continuously
③| HOME| Short Push: Transition to home screen Long Push: AA/CP voice
recognition
④| BACK| Transition to previous screen
Radio operation procedure
Operation procedure
-
(ACC-ON)
After the ACC-ON, confirm that Toyota screen is displayed. -
The screen is changed to “CAUTION” screen after a few seconds.
Note: It takes a little longer for the first time of ACC-ON. -
Press the “Continue” button on the face panel after a few seconds to move MENU screen
-
When the Radio Mode Window on the screen is pressed,”FM1″ screen is displayed.
-
Confirm that the screen is changed as below, Please push down the ”<”button or ”>”button. This will start to SEEK.
Same as AM mode.
Operating manual (Bluetooth/Handsfree)
-
(ACC-ON)
After the ACC-ON, confirm that Toyota screen is displayed. -
The screen is changed to “CAUTION” screen after a few seconds.
Note: It takes a little longer for the first time of ACC-ON. -
Press the “Continue” button on the face panel after a few seconds to move MENU screen.
-
Swipe down on the face panel to move to Notification screen.
-
Please press the “Setting” button on the face panel to move to Settings screen
-
Confirm if ”Settings” screen is displayed, select the ”Bluetooth” button on the display.
-
lease press the ”Add Device” button of the screen
-
Please press the ”Search Device” button of the screen
-
Confirm if screen is changed as below, Please set iPhone or iPod in pairing mode.
Displays when you have more than one pairing equipment
- Select the iPhone or iPod to connect.
Operate the phone after the message on the screen
- ”Connection Completed” is displayed if completed.
FCC Operating manual Requirement
CAUTION: Radio Frequency Radiation Exposure
This equipment complies with FCC radiation exposure limits set forth for
uncontrolled equipment and meets the FCC radio frequency (RF) Exposure
Guidelines. This equipment has very low levels of RF energy that is deemed to
comply without maximum permissive exposure evaluation (MPE). But it is
desirable that it should be installed and operated with at least 20cm and more
between the radiator and person’s body in normal use position.
Co-location: This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>