Denso 550-0103 TPMS 315-MHZ Sensor for Factory Alloy Wheel Options Instruction Manual
- June 5, 2024
- DENSO
Table of Contents
Denso 550-0103 TPMS 315-MHZ Sensor for Factory Alloy Wheel Options
Sensors are already programmed in the package, fix in tires then it’s ready
for use. Be sure to fix the sensor to the right tire according to the tire
position marked on each sensor.
4 Sensors are provided in the standard package, each one marked with its tire
position {LF, LR, RF, RR), as already paired with the monitor, please be sure
to fix the sensor in the right tire.
SPECIFICATIONS
- Detecting pressure range 0~8BAR (0~116PSI)
- Operation temperature -40°C-80°C
- Storage temperature -40°C-8S°C
- Frequency 433.92MHz
- Transmission power <l0dBm
- Pressure accuracy ±0.1 bar(± 1.5 psi)
- Temperature accuracy ±30(
- Dimension 75(L) x 62.S(W) x 21(H)mm
- Weight 29 g
INSTALLATION
Notice:
For tire already had an internal sensor installed, notify the technician of
the sensor location and be cautious during tire detaching and loading
(operate at 15cm or more away from the valve).
- Step 1. Detach off tire and deflate, remove the tire valve.
- Step 2. Screw off the dust cover, nut & washer from the sensor.
- Step 3. Fix sensor in lire rim.
- Step 4. Hold the sensor in position with your hand.
- Step 5. Re-screw back the washer, nut & dust cover, load tire to a vehicle, and inflate.
- internal sensor installation must be handled by technicians.
- Be cautious of sensors in tires during maintenance and detaching/loading tires.
- Each sensor is marked with tire position (as already paired with the monitor), be sure to fix the right tire.
- Monitor issues sensor low battery alert when the sensor battery almost runs out of power.
- After the sensor is installed in the tire, please examine the tire/valve with soapy water to prevent any air leakage.
OE
EU433-003
56029398AB| 68241067AA
9050030| 05154876AA
9054100| 53104671
9057200| 670002790
35400217| A0009050030
5154876AB| A4479050500
56029398AA| 4199034000
A0035400217| 56029400AB
A0009054100| 56029400AC
A0009057200| 56029400AD
A0035400217| 56029400AE
56029398AA| 68241067AA
56029398AB| 05154876AA
68241067AB| 53104671
A0009050030| 670002790
A4479050500| 68241068AB
4199034000| 56029400AD
56029400AB| 56029400AE
56029400AC|
US315-004
US315-004
10394110| 10394110| 20923680
12768826| 15268606| 4313078J00
13581558| 15825475| 25952370
13586335| 15921013| 15123145
15268606| 20925924| 13589597
15825475| 13586335| 13598255
15921013| 13598771| 23445327
20922900| 22853741| 15920615
20923680| 25799331| 4313078J10
20964159| 25920615| 4313085Z00
22854866| 1358635| 20922900
25799331| 15123145| 22854866
25920615| 15920615| 22959744
15922396| 20926680| 22853741
15254101| 15922396| 15254101
13598771| 20923680| 15922396
20964159| 25799331|
12768826| 15254101|
13581558| 25952370|
DECLARATION OF CONFORMITY
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>