SONOFF SNZB-02P Zigbee Temperature and Humidity Sensor User Manual
- June 6, 2024
- SonOFF
Table of Contents
SNZB-02P Zigbee Temperature and Humidity Sensor
User Manual
Product Introduction
Features
SNZB-02P is a ZigBee low-energy temperature & humidity sensor that can be used to monitor the environment temperature and humidity in real-time. Connect it with the Bridge and you can create a smart scene to trigger other devices.
Operation instruction
-
Download the eWelink App
http://app.coolkit.cc/dl.html -
Pair SON OFF ZB Bridge to your link account
-
Pull out the battery insulation sheet
The device has a version
with a battery and without a battery. -
Add sub-devices
Access eWeLink App, select the Bridge that you want to connect, and tap “Add” to add a sub-device. Then long-press the reset button on the device for 5s until the LED indicator flashes slowly, which means the device has entered the pairing mode, and be patient until pairing completes.
If the addition failed, move the sub-device closer to the Bridge and try again.
Installation methods
-
Placed on the desktop for use.
-
Tear off the protective film of the 3M adhesive and stick the device on the desired area.
Do not install on the metal surface, otherwise, it will affect the wireless
communication distance.
The device’s weight is less than 1 kg. The instant I la ti on the height of I
ess than 2 m is recommended.
Effective Communication Distance Verification
Install the device in the desired place, then press the “Reset” button on the
device.
The LED indicator flashes twice means the device and the device under the same
ZigBee network (the router device or hub) are within the effective
communication distance.
Specifications
| Model | SNZ13•0215 |
|---|---|
| Battery model | CR2450(3V) |
| Wireless connection | Zigbee 3.0 |
| Working temperature | 0°C-40°C |
| Working humidity | 10.90%RH(non-condensIng) |
| Material | PC VO |
| Dimension | 43x43x14mm |
Delete sub-devices
Long press the reset button on the sub-device for 5s until the LED indicator flashes three times. In this case, the sub-device is deleted from the Bridge successfully.
users can delete sub-devices directly from the sub-device page on APP.
FCC Warning
Changes or modifications not expressly approved by the party responsible for
compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Hereby, Shenzhen Son off Technologies Co., Ltd. declares that the radio equipment type SNZB-02P is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https://www.sonoff.tech/usermanuals
Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park, Shenzhen, GD, China
ZIP code: 518000
MADE IN CHINA
Website: sonoff.tech
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>