Hawk HCR400 Wireless 2.4GHz Laser Prensenter User Manual
- June 6, 2024
- Hawk
Table of Contents
Hawk HCR400 Wireless 2.4GHz Laser Prensenter
Welcome
Thanks for choosing this laser presenter. It gives you remote control of your
onscreen presentations with a range of up to 35 feet which is a prefect idea
for a large conference room.
This presenter supports the most common presentation tools including Page Up,
Page Down, Start & Exit slideshow , Screen black. It also has a laser pointer
that helps you focus in on your key messages. Just plug and play, no software
is required. It allows you to control your presentation with one touch easily
in the palm of your hand, and enjoy freedom of movement as you present.
Be sure to carefully read this User’s Guide first for the proper use of
this product and keep it for future reference.
© 2012 All rights reserved.
IMPORTANT SAFETY AND HEALTH INFORMATION
Package Contents
- Wireless 2.4GHz Laser Presenter x 1
- User’s Manual x 1
- Cable x 1
- Warranty Card x 1
Minimum System Requirements
- Windows® 98SE / 2000 / ME / XP / Vista / 7 / 8 or Above,Mac OS X® v.10.4 (or later)
- IBM or PC Compatible or Notebook with USB port
Product Features
Getting Started
STEP 1 Pull out the receiver
STEP 2 Connecting the Receiver Connect the USB connector of the receiver
into an available USB port of your computer.
STEP 3 Open the Powerpoint file and test the key functions
Trouble Shooting
| Question | Possible cause | How to resolve |
|---|---|---|
| Need to install software for first use of this product? | No, this is a plug |
and play device.
Need to link ID before first use?| | No need
Possible to use 2 or more of this product in a room at the same time?| | Yes
Remote control malfunction| Interfered by other RF signal| To Implement ID
Link (see Switching Channels)
Laser pointer and remote control both malfunction| Put batteries in wrong
direction or run out of battery power| Check the batteries
Switching Channels
Plug receiver to your PC USB port Within the 20-second stand-by time, press
and simultaneously 2 seconds until the red LED of Status indicating becomes
blinking for 2 times, the ID link has been successfully done.
Care and Maintenance
- For cleaning, you are advised to use a soft, slightly moistened cloth.
- Avoid using solvents or abrasive substances.
- Do not open the presenter: for maintenance, consult qualified staff only.
Safety Notice
- This product complies with FCC and CE rules.
- This product has no serviceable parts. Use of controls or adjustments of procedures other than the user guide may result in danger.
Specifications
| Frequency range | 2.4GHz |
|---|---|
| Remote range | About 30 meters |
| Power | AAA battery x 2 |
| Output power | Under SmW |
| Size | 134 (L) x 34(w) x 27 (h) millimeters |
| Weight | 40g |
FCC Requirement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>