BLACK HAWK ELECTRIC Urban Series Skateboarding User Manual
- June 5, 2024
- BLACK HAWK ELECTRIC
Table of Contents
- BLACK HAWK ELECTRIC Urban Series Skateboarding User Manual
- Safety Notice
- Components
- Charging
- Remote Control
- Pairing
- Speed Modes
- Basic Operation
- User Safety
- Further recommendations
- Battery Safety
- Battery Safety Continued…
- Mechanical Maintenance
- Skateboard Care
- Specifications
- Warranty and Guarantee
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BLACK HAWK ELECTRIC Urban Series Skateboarding User Manual
Safety Notice
Prior to riding the Black Hawk Electric Skateboard, it is important to read
through this user manual. All instructions and warnings should be followed to
ensure safe operation.
Proper judgment and sensible operation should be applied at all times when
operating the electric skateboard. This device uses brushless hub motors to
accelerate and brake while in operation. The skateboard is capable of high
speeds and fast acceleration that could result in serious injury or death if
not ridden carefully.
To minimize risk, please read this manual and only operate the skateboard in
safe environments.
Your skateboard can lose power or braking ability at any time so ensure you
only ever ride the skateboard at a comfortable speed similar to that of a
normal unpowered skateboard. Braking the skateboard manually with enclosed
footwear may be required in an emergency.
Always wear a helmet and ensure protective gear such as knee pads, elbow pads,
and wrist guards are considered. Falling from the skateboard at high speeds
can cause serious injuries so protect yourself with appropriate protective
equipment.
For more information on our product disclaimer please visit
blackhawkelectric.com.au
Safety checks all riders must complete before operating their electric
skateboard before each and every use:
- Turn on both the skateboard and the remote controller.
- Test functions of the remote controller with the skateboard’s motor(s) held up off the ground.
- Test acceleration and braking to ensure that the remote controller’s joystick is functioning and returns to neutral when released.
- Ensure all fittings, fixtures, and components are tightened and safe to ride on.
Components
- See below the breakdown of all components
- Front Wheels
- Front Trucks
- Deck
- Rear Trucks
- Rear Wheels
- Battery
- On/Off Switch
- Charge Port (on another side)
Charging
Charging of your electric skateboard is made simple thanks to an intelligent
smart charger and an on-board Battery Management System, (BMS).
When charging it’s important to connect the charger and charger cord to the
power outlet, (wall socket) before connecting to the skateboard.
Your charger has two lights to display the charging status.
A red light means your charger is connected and charging the battery. A green
light means the charger has finished charging the battery. It can also mean
the charger is not connected. Charging the Electric Skateboard takes 3-4 hours
from empty Charging the hand control is also a simple process thanks to a one-
piece USB charging cord. Connect the hand control to a 5V USB output via the
supplied cord. Charging the remote battery usually takes about 30 minutes.
Remote Control
Controls
- Accelerate
- Brake
- Index Finger Hole
- Forwards / Reverse
- Power/Mode Button
- Battery Level Indicator
- Charge Port
- Safety Lanyard
Pairing
Fro m new, your remote controller is already paired to your skateboard during
quality control testing.
Sim plies power on your skateboard and then also your remote controller. The
connection light will show connectivity.
Should you need to repair your remote, please follow these steps.
- Turn on both the board and the remote controller.
- Hold down the board’s on/off switch for 5 seconds until the indicator light flashes.
- Using a small/sharp object, press the sunken reset button on the remote control. Repeat until paired.
Speed Modes
The remote controller features 4-speed modes. The speed modes can be changed
by quickly pressing (not holding) the power button to toggle through the power
modes. The power mode will be shown on the battery meter for a short time
after the power mode has been changed.
In the low setting, the skateboard operates in the beginner mode, (Speed Mode
1). Then progressively faster in modes 2 and 3. Finally, in level 4, the
skateboard operates in the advanced setting. We recommend the use of Speed
Mode 4 in wide-open spaces only.
Basic Operation
Riding Style
It is important to make sure you’re comfortable and ensure you’re riding with
the correct stance. You can ride in two different stances as shown below:
Balance
This electric skateboard uses a powerful motor that can throw you off balance
when accelerating and also decelerating. It is important to pre-empt these
forces and counteract the propulsion and/or the slowing-down of the
skateboard.
When accelerating you will need to either lean slightly forwards or transfer
weight onto your front foot.
When decelerating you will need to either lean slightly backward or transfer
weight onto your back foot.
Gentle Control Inputs
When operating the hand control the rider must use a careful amount of input
onto the speed/braking controller. Similar to operating a vehicle or
motorbike, slow and small movements of the control(s) are crucial.
Fast or erratic inputs to the speed controller will likely cause a loss of
balance and lead to the rider falling from the skateboard.
Smart Speed Mode Changing
The very latest Black Hawk Electric skateboards have the ability to change
speed modes in a smart and safe way without having to take your eyes off the
path. Looking down at your remote to find the speed mode button can cause
distraction, so the easier way is as follows.
While under throttle, reduce speed back to the neutral position with the thumb
lever slowly, then without braking, accelerate upwards again with the thumb
lever. This will cycle you through the speed modes continuously in an
increasing manner without having to press any other buttons or distract
yourself from riding safely. The speed mode will not be increased if you
engage the brakes, for safety reasons.
User Safety
Limitations
It’s important to understand what the skateboard is capable of. This includes
environment, surroundings, traffic, and weather. We recommend the use of the
skateboard on smooth, even surfaces away from other vehicles and pedestrians.
Operation of the skateboard on damp roads or in light rain is not permittable
and any exposure to water or moisture should be avoided. (See warranty
information). Riding the skateboard in wet conditions will compromise
traction, braking, and turning abilities. All Black Hawk boards have measures
in place to show to us any evidence of contact with water.
Things you should avoid
- Bumps, cracks, and uneven surfaces
- Rocks, gravel, and pebbles
- Steep hills
- Water and wet surfaces
- Sand, grass, and dirt
Further recommendations
- Always wear protective equipment
- Never wear loose clothing that could become caught under the wheels
- Avoid obstructions that could compromise your balance
- Avoid gutters, curbs, steps, and driveways
- Apply caution in new areas that you’re not familiar with
- Apply caution around pedestrians and always give way
- Avoid speeding up behind pedestrians
- Avoid shared traffic conditions with other motor vehicles
For more information on what the skateboard is capable of and warranty terms please visit the warranty information on page 14 of this user manual or on our website at: blackhawkelectric.com.au
Battery Safety
It is important to follow and observe all safety information to ensure the safe use of the electric skateboard and battery.
- Do not use a skateboard if the battery pack is broken or pierced.
- Do not use a skateboard if the battery pack emits an unusual smell, smoke, or excessive heat.
- Do not use a skateboard if the battery pack leaks any substance and avoid contact with the battery.
- Keep out of reach of children and pets.
- Exposure to battery voltage could result in serious injury or death.
- Unplug or disconnect the skateboard from AC power before removing or attaching the battery or performing any service.
- Never work on the skateboard when it is plugged into an AC power source. You may risk serious injury from electric shock as well as damage to the
- skateboard.
- The cells within the battery contain toxic substances.
- Do not attempt open batteries. Do not insert any objects into the battery or use and device to pry the battery out of the skateboard.
- If you insert an object into any of the battery ports or openings you could suffer electric shock, injury, burns, or cause a fire.
- Attempting to open the battery casing will damage the casing and could release toxic and harmful substances and render the battery pack and
- skateboard useless and warranty voided.
- Observe and follow all safety information on the warning label found on the batteries.
- Failure to charge the batteries could result in permanent damage to them. Left unplugged, the batteries could fully discharge over time and could cause
- permanent damage rendering the battery pack and skateboard useless and warranty voided.
Battery Safety Continued…
- Only use chargers supplied and approved by Black Hawk Electric and never attempt to bypass or override the protection circuits.
- Do not attempt to wash the skateboard with water or high-pressure water washers.
- Avoid getting water near or into the charge port.
- Do not fit or install any voltage measuring devices to any components.
- Always make sure that the charger port is dry before you connect the charger cord.
- Do not submerge the battery, skateboard, or charger into water. If you suspect the batteries or skateboard have been submerged or experienced water
- intrusion, do not attempt to remove the batteries.
- Do not plug the charger into the board if the skateboard, battery, motors, or charger has been submerged or exposed to water ingress.
- As will all rechargeable batteries, do not charge near flammable material or liquids.
- If you use, charge or store the skateboard outside the limits specified, you may void the warranty. You may also damage your batteries and/or
- experience a reduced range and inconsistent battery charging.
- Do not leave the skateboard charging or stored in any room, dwelling, vehicle, or confined space that is above 30° Celsius or below 5° Celsius. Leaving
- your skateboard in a hot vehicle may cause damage to the battery, motors, vehicle, or surrounding environment.
- Lithium-Ion batteries are classed as, “Hazardous Materials.” Transporting Lithium-Ion batteries by air or other methods may be prohibited by policies
- or law.
- Contact the designated company or agents transporting the skateboard for their rules and regulations.
- Failure to follow these instructions could cause electric shock, injury, burns, or cause a fire.
Mechanical Maintenance
Truck Adjustments
Adjusting the turning ability of the skateboard is made simple with the
included multi-tool and the built-in hex key. Whilst we recommend leaving both
front and rear trucks as is from new, higher speed riding may require stiffer
trucks to avoid becoming unbalanced at high speed.
To tighten your trucks, connect your multitool to the black nut of the truck
and tighten to the right in a clockwise direction. Only small adjustments are
needed. To loosen, reverse the above. Be sure never to loosen the trucks too
much as this is a serious safety risk.
The Mtn Board V3 features Double Kingpin trucks which can be adjusted on two
levels. We recommend keeping the highest adjustment (closest to deck) tighter
and then using the lowest adjustment, (closet to ground) for primary
adjustments.
Component Removal
Removing any components without permission from Black Hawk Electric may void
your warranty. Replacing the battery, controller, a motor or any other working
component should only be done after the 12-month warranty period has finished
Skateboard Care
Wooden Deck
It is important to take care of the wooden deck used with this model. For
example, we recommend storing the skateboard upright on its wheels. Resting
the skateboard on its nose or tail will result in scratches, wear, and
possible damage to the deck. Repairing the wooden deck is difficult, costly,
and may void your warranty.
Fittings
For the metal components of the skateboard such as the trucks, we recommend
checking overall fastenings every few times the board is ridden to ensure all
are tightened appropriately. Riding the skateboard sends vibrations through
all components and can over time lead to the loosening of some fasteners. A
simple ‘once-over’ with an Allen key and spanner to the trucks (top and
bottom) is all that is required.
Wheel Wear
Wheel wear can occur faster than other typical skateboard wheels. Should you
notice wear on your tires it is important to monitor this wear and ensure the
wheels are replaced before riding stability or motor safety is compromised.
Grip Tape
The grip tape used on the skateboard is tough wearing however it is expected
to wear and decrease in grip with the usage of the board. We recommend
mounting and dismounting the skateboard without scrubbing the grip tape too
much to extend its lifetime.
Specifications
Motors | 1000W Brushless x 2 |
---|---|
Battery | LG 6.6Ah 36V Li-ion 10S 3P |
Deck Material | Layered Bamboo |
Speed | Up to 30km/h (on-road) |
Range | Up to 20km (on-road) |
Hill Gradient | Up to 10% (on-road) |
Weight | 15kg |
Charge Time | 3 Hours |
Warranty | 12 Months |
Deck Dimensions | 97cm long x 24cm wide |
Tires | 19cm x 5cm airless tire |
Wheels | Aluminum Cast |
Trucks | Double Kingpin Aluminum 30cm wide |
Remote | Ergonomic Bluetooth remote |
Weight Limit | 100kg |
Intended Usage | Recreational use |
Age Limit | 15+ |
Warranty and Guarantee
This agreement outlines the warranty coverage supplied by Black Hawk Electric Pty. Ltd. The company warrants that the product will be free from defects in materials and workmanship for a period of 12 months. If the product proves defective under normal usage within the limitations given, a claim must be filed during the warranty time period. If the product is proved faulty under normal usage, Black Hawk Electric will at its discretion:
- Repair the product by means of email support with supplied photos and/or footage to demonstrate the fault or issue from the customer.
- Repair the product with new or refurbished parts within a reasonable time frame.
Warranty matters cannot and will not be discussed through telephone discussions as all matters must be written in an email to keep a paper trail of all things said. The following situations are beyond the warranty inclusions:
- Damage has been caused by modification or use outside what is specified within the product limitations.
- The product has been dismantled or repaired by an unauthorized third party.
- Damage or fault has been caused by other issues.
- Natural wear and tear do not affect product function, including scratches, wear and tear on deck, grip tape, bearings, wheels, and wheel skins.
- The total distance traveled is over 1500km.
- Damage caused by accidents, such as: dropping the skateboard or leaving the skateboard in a wet environment where rust or corrosion has developed
- on the skateboard. This includes coastal areas where salt spray is abundant.
- Damage caused by overloading the electric skateboard.
- Damage caused by water.
- Damage is caused by natural events such as fire, flood, storm, or extreme temperatures. Contact Black Hawk Electric for any warranty-related matters.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>