Mirabella genio I002923 Smart Wi-Fi LED Stick Light Instruction Manual

I002923 Genio Smart Wi-Fi LED Stick Light

WARNING:

• SAFETY EXTRA LOW VOLTAGE TRANSFORMER MUST REMAIN INDOORS ONLY – IT CANNOT BE  XPOSED TO THE WEATHER

TO ENSURE THE SAFE AND SATISFACTORY OPERATION OF THIS SET PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE REFERENCE
FOR ANY QUESTIONS OR TROUBLESHOOTING PLEASE VISIT www.mirabellagenio.net.au/faqs
We recommend that the set be tested prior to being set up in the desired location

SAFETY INFORMATION:

• Remove set from the packaging before connecting to the power supply.
• Before using or re-using the set, inspect carefully
• Use only with transformer supplied
• Do not connect set electrically to another set
• Do not use any set which has: – cut, damaged, or frayed wire insulation, cracks in lamp-holders, loose connections or exposed wires
• The LED bulb is not replaceable

Wi-fi controller

Note: When connecting, please ensure the arrows are aligned with one another

Included in the Kit

Rubber end cap

Install the APP and register Account

http://www.mirabellagenio.com.au/smartapp

For the best experience, download the “Mirabella Genio” APP to your the smartphone from App Store or Google Play, or you can also scan the QR code below, the APP icon will be displayed after it’s installed successfully

Link and connect the stick light

It is recommended you connect the stick light according to the ABCD marking. A-A, B-B, C-C D-D, etc, and cover the end with a rubber end cap.

Pairing using Mirabella Genio App

1. Connect the stick light then Switch on power at the wall, wait a few seconds, stick light will start to blink rapidly (2 blinks per second)
2. If it failed to blink rapidly when first powered on, press and hold the pairing button on the Wi-Fi controller until the light starts to blink rapidly
3. Check and verify your mobile phone is connected to a 2.4Ghz Wi-Fi network (5Ghz Wi-Fi is not supported and may need  to be disabled on the router setting in order to make successful pairing and overall performances)
4. Open Mirabella Genio APP, tap on +, go to Smart Light -> Genio Smart Lighting
5. Follow the App instruction to finish the pairing process

During the connection 0-100% countdown, the light will stop blinking., HOWEVER, after the end of 100% countdown, if the APP display device not found error, this means the APP failed to communicate with our cloud services.
– Please ensure the 5Ghz Wi-Fi signal is disabled on the router setting, please contact your internet provider
– Please ensure your phone is connected to a 2.4Ghz Wi-Fi signal, Wi-Fi name should not end with -5G
– Please ensure you enter the correct Wi-Fi name and password
– Please check light is blinking rapidly (2 blinks per second) before starting the pairing process

Should the transformer, supply plug, or supply flexible cord get damaged, do not attempt to repair.
TO BE REPAIRED BY AN AUTHORIZED PERSON ONLY
THIS IS AN AUSTRALIAN STANDARDS REQUIREMENT IN THE INTEREST OF YOUR SAFETY·

I am using Telstra NBN, I disabled the 5Ghz and I still cannot get it to pair?
Please follow the Guest Network paring instructions on https://mirabellagenio.net.au/faqs

If you have done all of the above, ensuring that the 5Ghz is disabled and the light can stop blinking but doesn’t pair in the APP then your modem could be incompatible with our smart device.

Specifications

• 12 LEDs per stick
• Length of stick = 40cm
• Adaptor Output: 12V DC 0.5A
• IP20

MIRABELLA INTERNATIONAL PTY LTD 1 MIRABELLA DRIVE, TULLMARINE, VIC, AUSTRALIA 3043
TOLL-FREE: 1800 636 528, www.mirabellagenio.com.au
V4 30/10/2020

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>