Mirabella genio I003981 Wi-Fi 12 LEd Bulb Hollywood Mirror User Guide
- June 6, 2024
- Mirabella genio
Table of Contents
Mirabella genio I003981 Wi-Fi 12 LEd Bulb Hollywood Mirror
WARNING: TO ENSURE THE SAFE AND SATISFACTORY OPERATION OF THIS MIRROR
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE REFERENCE
SAFETY INFORMATION:
- Remove set from the packaging before connecting to the power supply.
- Before using or re-using the set, inspect the set carefully
- Use only with the adaptor/transformer supplied
- Ensure that the cable is completely uncoiled whilst set is in use. Failure to do so may cause overheating and malfunction
- Avoid damage to wire insulation (cable), as this could cause a short-circuit and damage the transformer
Connection Preparation
Your phone must be connected to 2.4Ghz Wi-Fi and not the 5GHz, To verify your
mobile phone is connected a 2.4Ghz Wi-Fi network, Navigate to the Setting menu
and click on Wi-Fi. In this menu you will see all detectable networks in your
area. Locate the SSID for your network, select a Wi-Fi SSID that doesn’t end
with 5GHz.
Check you have a strong Wi-Fi signal (at least two bars) in the location where
the smart device is installed.
If you don’t have at least two bars signal on your phone, then you may need to
reconsider the location or getting a Wi-Fi extender to boost the Wi-Fi signal
strength.
If you have dual-band router but you don’t see two Wi-Fi name SSID’s, one with
5G and one without 5G, you MUST log into the router and manually disable the
5Ghz Wi-Fi signal if you’re having connection issues. Please contact your
internet provider on how to disable 5Ghz Wi-Fi for your router.
Install the APP and register Account
For the best experience, download the “Mirabella Genio” APP to your smartphone from the App Store or Google Play, the APP icon will be displayed after it’s installed successfully
Bluetooth pairing assistant function
Our latest genio smart Wi-Fi device got a Bluetooth pairing assistant
function, to make the pairing even easier than before, to take advantage of
this function, please turn on the Bluetooth function on your phone, connect
the adaptor to the mirror light and turn the wall switch power on, wait for
the light starts to blink rapidly (2 blinks per second)
if it does not automatically start to blink rapidly when first powered on,
press and hold the Colour button on the mirror , and until the light is rapid
blinking (2 blinks per second)
- open Mirabella genio APP, tap on + , follow the below steps to pair the mirror light into your APP, please make sure you are using the 2.4Ghz Wi-Fi name and password, do not use the Wi-Fi Name that end with —-5G
If this method doesn’t work for you, please Turn
OFF your Bluetooth on your phone, then try EZ or AP method
EZ method – when the light is fast blinking (2 blinks every second)
Open Mirabella Genio APP, tap on +, add Manually then choose genio strip light from the list
- Entre your 2.4Ghz Wi-Fi name and password, (make sure Wi-Fi name doesn’t end with -5G) Follow the APP instruction carefully to complete the network pairing process.
AP method – when the light is slowly blinking (1 blink every 2 seconds)
if the fast-blinking method (EZ method, mentioned above) doesn’t work, please
try the slow blinking (AP method) below.
While the mirror light is rapidly blinking, press and hold the colour button
again and wait for the light to start to blinking slowly (1 blink per every 2
seconds)
-
open up the Mirabella genio APP, tap on + , add Manually then choose genio strip light from the list.
Enter your 2.4Ghz Wi-Fi name and password, (make sure the Wi-Fi name doesn’t end with -5G) then in reset the device first screen tap on EZ mode in the Top right hand corner just below the battery icon , select AP Mode (refer to the 1st and 2nd image below) Now Confirm indicator slowly blinking (refer to image 3), hit Next, then Go to connect and connect to Wi-Fi named SmartLife_XXXX
Note: If you failed to see Wi-Fi name beginning with the word SmartLife_XXXX, then mean the device is not slowly blinking, please reset and make sure it is slowly blinking -
After connected to SmartLife_XXXX, return to Mirabella Genio, APP will commence the adding device process
Should the transformer, supply plug or supply flexible cord get damaged, do
not attempt to repair.
TO BE REPAIRED BY AN AUTHORIZED PERSON ONLY
THIS IS AN AUSTRALIAN STANDARDS REQUIREMENT IN THE INTEREST OF YOUR SAFETY·
FAQ
Q. I have internet/power outage and the device went offline and doesn’t
reconnect back online?
A. Go to the device’s settings page (pencil or … icon), look for “remove
device” Remove it and reset the device,and pair it again through the app.
If you still having an issue with pairing after use AP method, please check our online FAQ pages on www.mirabellagenio.com.au/faqs or contact Mirabella technical support line.
Mirabella International Pty Ltd
1 Mirabella Drive Tullamarine VIC. 3043 Australia t: 1800 636 528
e: genio@mirabella.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>