SmallRig Fold P10 Phone Cage for Videography User Manual
- June 6, 2024
- SmallRig
Table of Contents
SmallRig Fold P10 Phone Cage for Videography User Manual
In order to ensure users’ safety and prevent damages to the product due to any improper use, please carefully read the “Warnings” below and properly keep this User Manual for future reference
Foreword
Thank you for purchasing SmallRig’s product.
Warnings
- Please read this User Manual carefully.
- Please do not use the product in water because it is not dust or water proof.
- The Phone Cage for Videography contain electronic originals, do not let the product fall to the ground, be hit, or suffer a violent impact.
- The Phone Cage for Videography contains a detachable lithium battery.
- When the battery of Phone Cage for Videography is not in use for a long time, the battery should be removed to prolong the battery’s service life.
- Since there are some hazardous substances in the battery of the Phone Cage for Videography, please do not discard it. Instead, dispose of the product that is damaged or will never be used according to the waste management measures.
- When the Phone Cage for Videography is not in use, it should be stored in a dry and clean place. Avoid high temperature, high humidity, and strong magnetic field.
- Do not install objects beyond the load-bearing range of the Phone Cage for Videography, otherwise the product may be damaged.
- Do not disassemble the product without permission.
Please do not disassemble the product or change its battery. If you have
any question, please contact the seller to apply after-sales service.
Intended Use
- Please read this User Manual carefully, especially the “Warnings”.
- Please use or store the product in the environment mentioned herein.
- Failure to use the product as per this User Manual or under the specified working and storage conditions will be deemed as improper use.
Package List
The package include the following items:
-
Phone Cage for Videography x1
-
Lithium Battery x1
Replace Battery
-
Press down lightly the battery door lock on the side of the wireless control handle.
-
Pull out the battery door through the groove.
-
Insert a CR1632 lithium battery (please note that the positive terminal faces towards the wireless control button).
-
Insert the battery door (please note that the battery door lock faces towards the wireless control button).
-
Long press the wireless control button and the indicator light is on, then you finish replacing the battery and it can be normally used.
Wireless Remote Control
- Long press the wireless control button for 3 seconds to enter the wireless pairing mode, at this time the LED indicator light flashes blue.
- Turn on your smartphone’s wireless control and select “SmallRig CG01” for pairing.
- When pairing is complete, the LED indicator light turns blue (only pairs one device at one time)
- Manually switch to the phone shooting or recording mode, press the wireless control button to start/stop taking pictures or recording.
- No need to pair again after the first successful pairing.
Guarantee Card
Serial No.|
---|---
Item Name|
Purchase Date|
User Name|
Mobile|
Address|
Receipt|
Service Warranty
Our company offers one (1) year of warranty service for the buyers.
Important:
Please keep your original receipt and guarantee card. Be sure the dealer has
written on it the date of purchase and SN of the product. These are required
for warranty service.
This warranty does not cover.
Defect caused by users’ violation of the “Warnings” and “Intended Use”.
Cosmetic defects that appear more than fifteen (15) days after the date of
purchase. Cosmetic damage caused by improper handling is also excluded. Damage
that occurs while the product is being shipped to whoever will service it.
This warranty is void if:
The product identification or SN label is removed or defaced in any way. The
product is serviced or repaired by any one other than our company or the
service agency authorized by our company.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used with minimum distance 0mm between the radiator and your body.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
The device has been evaluated to meet general RF exposure requirement. The device can be used installed and operated with minimum distance 0mm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>