ZKTeco TL700 Fingerprint Smart Door Lock Installation Guide

: June 6, 2024
: ZKTECO

Installation Guide
Model: TL700
Version: 1.0

Important Notes

Please read this Installation Guide carefully and contact the Customer Care Service if you have any questions about the installation.
To avoid any future service charges that can arise as a result of incorrect installation, it is recommended that installation can be performed by a professional technician to prevent any potential service charges that can occur due to incorrect installation.
We regularly revise the contents of this Installation Guide and update our products to enhance quality and performance without prior notice.
You must perform the initialization process on each installation immediately after installing this lock on any door, as described in the initialization procedure on page 8.
Do not install the batteries until the lock is installed.

What’s in the Box

Note:
The spindles and screws are designed to ﬁt doors with a thickness of 45mm to 60mm, and one of the screws C needs to be cut, how to cut it just like the below diagram.

Screws Length Cutting Comparison Table

| Door Thickness
45-60mm| **
Screw C at battery compartments| 13mm
Screw C at the bottom| 0mm**

Installation Diagram

Installation Procedure

1 Door Properties

A. Measure the Door Thickness
Measure the thickness of the door and cut the Spindle and Screws to the proper length. For further details, please refer to the table on Page 1.
B. Check the Door Opening Direction
The position of the handle is determined by the opening direction of the door. Below is the graphical representation of the door opening direction in reference to your position outside the room.

Adjust the Direction of Latch (if needed)

Push the reverse block in an upward direction.
Push the bolt of the latch into the mortise.
Rotate the latch bolt to 180° inside the mortise, and release it.

C. Change the Handle Direction (if needed

Remove the directional screw of the handle, rotate the handles of the outdoor and indoor units to 180 degrees in the left or right direction, depending on the door.
Secure the handle again with the directional screw.
Note: Before changing direction, please make sure the Security Knob is on the right side.

Drill Holes on the Door

Place the installation template at the desired handle height.
Mark the holes to be drilled and drill the marked locations.

Install Mortise and Cylinder

Put the Mortise into the hole that was drilled and secure the Mortise with Screw A.
Insert the Cylinder into the Mortise (the front sides and back sides) and secure it with Screw B.

Install Spindle and Studs

Insert the Spindle A into the clutch, then insert the Metal Pin from the bottom of the clutch, forcing the pin apart and bending it to hold the Spindle A.
Then, install the studs.
Note: After installing the spindle, please turn the clutch direction in the door open direction, the lock in the picture is right to open, so the clutch was turned to the right side.

Install the Outdoor Unit

Pass the outdoor unit cable through the top of the cable hole.
Pass the Spindle A through the hole of the clutch and the outdoor unit must be close to the entrance.

Install Indoor Unit

Insert the Metal pin on Spindle B, and uninstall the battery cover.
Connect the cable to the Indoor Unit port.
Place the Indoor Unit appropriately on the Mounting Plate and use Screw C to protect the Indoor Unit.
Then install the batteries and plug.

Install Strike Plate and Box

Make sure that the Strike Box is aligned with the latch bolt. Then, use the installation template to drill the holes.
Align the Strike Plate and Box with the holes drilled and protect them with Screw A.

Physical Test

A. Test the lock by rotating the handle and the double locking knob.
Note:

The front handle can be rotated even when the door is closed, but the door remains unlocked.
When the Security knob is turned on, the door remains unlocked even if the handle is rotated from indoor.
If the push handle is downward then the lock closes. It is an installation problem, please refer to step 4 installation.

B. Test the lock by using the mechanical key

Press and rotate the cover of the keyhole to 180° with your ﬁnger.
Insert the Key into the keyhole and rotate 90°.
Note: Please secure your keys for emergency purposes.

User Manual

Important Notes

TL700 is an intelligent Smart Lock. If the lock is not installed properly, it may aﬀect the lifetime of the lock. We suggest you to install the lock after furnishing. Please prefer a professional technician to install the lock as per our installation standard.
Please initialize the lock after installation and set the Administrator immediately to avoid others opening the door illegally.
To ensure your security, please check the box of keys when opening the product package.
Please keep the mechanical keys in a separate place to avoid any criticality.
Please keep your Administrator’s information conﬁdential.
To use the lock more eﬃciently, please refer to the User Manual before using the lock. If you have any queries, please feel free to contact the Company’s Client Service Center from any place or contact the Service Center headquarters.
Please visit our company’s website at any time for our service information and regular updates of products.

Product Overview

Definitions

User Roles: The lock can be handled by two user roles namely Administrator and User. The Administrator has the privilege to access the menu and open the door. The user has the privilege to only open the door.
Note: Each user can register ten ﬁngerprints, one password, and one card.
Initialization: All the registered user data will be deleted and restored to the factory settings, and the default password is 123456, any ﬁngerprint or card is valid.
Random Password: To protect the password, users may enter their password with random digits before or after the actual password. The maximum number of entered digits must be less than or equal to 30. For example: If the correct password is 123456, then the random password can be 89123456807, 1234562363, 389123456, etc.
Backup Enrollment: After the ﬁrst registration, users can change the registered password and card, or continue to register the remaining ﬁngerprints.
Always Open Mode : This function is to keep the door always unlocked, which is suitable for meeting rooms and places with no access restriction.
Low Battery Warning: When the battery power is low, the lock will prompt “Low battery, please change! ” after being turned on. If lower, the lock will prompt ”Low battery, shut down soon!”, users cannot access the Main Menu.
Emergency Charging: The bottom of the outdoor unit is provided with a Micro-USB interface. Use a power bank to charge the lock when it is out of power.
Emergency Mechanical Key: The mechanical key is used to open the door when the lock has an electronic malfunction.
Double Locking: Double locking prevents the lock from being unlocked from the outside. Users can enable it by rotating the double locking knob.
Security Mode: If the security knob is turned on, an intruder cannot unlock the indoor lock by breaking the Peephole. In addition, it is eﬀective to prevent your child from wandering away from home.
Quick Close Function: Push the handle of outdoor unit upward, the latches will pop up to close the door.
Doorbell Function: It has an integrated doorbell function on the keypad, the customer does not need to deploy an additional doorbell at all.

How to Use

Reset the Lock

Press and hold the Reset button for 5 seconds. The lock will beep 5 times. Keep holding the Reset button until you hear the audio prompt, please press the # key to conﬁrm.

Activate the Lock

Touch the keypad with the back of your hand or ﬁngers to activate the lock.

Register the First Administrator

Press and hold the Reset button for 5 seconds. The lock will beep 5 times. Keep holding the Reset button until you hear the audio prompt, please press the # key to conﬁrm.

Touch the keypad to activate the lock.
Press the * # key to start the administrator registration process. The user will hear a prompt “Please register administrator, please enter ﬁngerprint, password, access card, press start to exit”.
Press the ﬁngerprint for ﬁve times, enter the group password, or swipe the access card.
Proceed further according to prompts.

Touch the keypad to activate the lock.
Press * + # key to access the menu.
Verify the administrator’s identity with his/her ﬁngerprint or card, or by entering the password then press the # key to conﬁrm.
Enter the digit corresponding to the function to be performed by following the audio guide.

Note:

The registered password can be 6 to 12 digits.
The currently logged-in administrator cannot delete his/her admin data.

Quick Start

Attention: If the veriﬁcation is failed for ﬁve times, the lock will generate an alarm.

Unlock the Door with Fingerprint

Press the registered ﬁngerprint on the ﬁngerprint sensor| Rotate the handle down to open
---|---

Unlock the Door with Password

Touch the keypad to activate the lock| Enter the registered password and press the # key to conﬁrm| Rotate the handle down to open
---|---|---

Note: Users may enter random passwords to prevent any person from observing the password. The maximum length of the random password is 30 digits.

Unlock the Door with Card

Swipe the registered card on the detection area| Rotate the handle down to open
---|---

Warning:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.

IMPORTANT! Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.