CORE INOVATIONS CTP800BD Shipping Label Thermal Printer User Guide
- July 11, 2024
- CORE INOVATIONS
Table of Contents
SHIPPING LABEL THERMAL PRINTER
Quick Start Guide
Download the free app and start printing instantly! Scan this QR Code or visit www.coreinnovationsinc.com/printer
CTP800BD
Printer Overview
- Feeder Button/ Status Light
- Release Tab
- DC Port
- USB Port
- Power Switch
In The Box
| |
---|---|---
1 x Shipping Label Printer| 1 x Label Stand| 1 x USB Cable
| |
1 x Power Brick| 1 x Power Cable| 1 x USB-C’ Adapter
| |
50 x Thermal Labels| 1 x Quick Start Guide| 1 x Warranty Card
Label Setup
- Gently pull the release tabs on both sides of the thermal printer to open the printer latch.
- Insert the thermal labels into the back of the printer, ensuring the peelable side is facing upward.
- Press and hold the feeder button until you hear a beep. The printer will automatically feed the label.
Bluetooth® Setup
Before initial use, make sure to disconnect from other nearby paired devices.
1. Plug in the power adapter, and press the power switch at the back of the
printer
2. Download the free InstaPrint app by searching for it on the App Store® or
Google Play™. No sign-up necessary
3. From the home page tap “+”
4. Tap “Shipping Thermal Printer”
5. On the list of Bluetooth® devices page, look for “Label Printer” and tap
to connect
Computer Setup
- Download the Windows™ or MacOS® printer driver at: www.coreinnovationsinc.com/printer
- Install the downloaded driver and follow the on-screen instructions
- Connect your printer using the included USB cable (use the USB-C® adapter if needed)
- Start printing by selecting “ CTP800BD ” from the printer list when prompted
Important Safety Warning
Avoid using or storing in the following locations. Damage to the printer may be caused.
- Do not leave in an exposed area with direct sunlight or near heat-generating equipment.
- Do not leave in an area where temperature or humidity is excessively high or low, or changes radically.
- Do not leave in an area exposed to water or liquid.
Avoid dropping or harsh impact to the printer, as damage may be caused.
Avoid entry of foreign objects or materials, as damage may be caused.
When cleaning do not use volatile liquid (thinner, benzine, etc.) or wet
cloth. Deterioration or discoloration may occur. Use a dry, soft cloth.
Do not move the printer or place harsh impact on printer while in printing or
standby operation. Printer power may disconnect and print data may be lost.
Please mind the paper cutting teeth. This area is sharp and can cause harm if
not careful.
This device contains small parts and is not recommended for kids under 3 years
old.
Adult supervision is recommended for kids under 13 years old. This equipment
is not suitable for use in locations where children are likely to be present.
Disassembly of printer will cause damage and void warranty.
If severe bulging occurs to battery, please discontinue use. Do not touch the
printer head. Please use a compressed air duster (sold separately) to gently
remove dust particles and debris.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation 1s subect to the
following two condons: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation. Any changes or modations not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in exposure condition without restriction.
Need Help?
Email us at support@dpaudiovideo.zendesk.com or call us at 1-833-909-CORE (1-833-909-2673). We are available Monday -Friday, 9am-5pm PST, except major holidays.
For information on recycling, please visit
https://www.coreinnovationsinc.com/support
© 2024 Core Innovations. All rights reserved. Core Innovations is a trademark of DP Audio Video. © 2024 Bluetooth SIG, Inc. All rights reserved. The Bluetooth® trademarks including the BLUETOOTH word mark, the figure mark (the runic “B” and oval design), and the combination mark (Bluetooth word mark and design) are owned by the Bluetooth SIG. These and all third party trademarks are the property of their respective owners. Used with permission. USB is used to solely describe the compatibility of our technology and in no way is intended to infringe on any intellectual property rights of any respective protected marks. © 2024 Google Inc. All rights reserved. Google, Android and Google Play are trademarks of Google LLC. © 2024 Apple Inc. All rights reserved. Apple and App Store are trademarks of Apple LLC.