ADJ LTS 50T AS Portable Trussing System User Manual
- June 13, 2024
- ADJ
Table of Contents
LTS 50T AS
User Manual
LTS 50T AS Portable Trussing System
©2023 ADJ Products, LLC all rights reserved. Information, specifications,
diagrams, images, and instructions herein are subject to change without
notice. ADJ Products, LLC logo and identifying product names and numbers
herein are trademarks of ADJ Products, LLC. Copyright protection claimed
includes all forms and matters of copyrightable materials and information now
allowed by statutory or judicial law or hereinafter granted. Product names
used in this document may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged. All non-
ADJ Products, LLC brands and product names are trademarks or registered
trademarks of their respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages,
injuries to any persons, and direct or indirect economic loss associated with
the use or reliance of any information contained within this document, and/or
as a result of the improper, unsafe, insufficient and negligent assembly,
installation, rigging, and operation of this product.
ADJ PRODUCTS LLC World Headquarters
6122 S. Eastern Ave. | Los Angeles, CA 90040 USA
Tel: 800-322-6337 | Fax:
323-582-2941 |
www.adj.com |
support@adj.com
ADJ Supply Europe B.V.
Junostraat 2 | 6468 EW Kerkrade | Netherlands
Tel: +31 45 546 85 00 | Fax: +31 45 546 85 99 |
www.adj.eu |
service@adj.eu
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the environment. Please
turn off all electrical products when they are not in use. To avoid power
consumption in idle mode, disconnect all electrical equipment from power when
not in use. Thank you!
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest
revision/update of this manual before beginning installation and/or
programming.
| Date | Document Version | Software Version | DMX Channels | Notes |
|---|---|---|---|---|
| 7/19/2023 | 1.0 | N/A | N/A | Initial release |
GENERAL INFORMATION
INTRODUCTION
Please read and understand the instructions in this manual carefully and
thoroughly before attempting to operate this device. These instructions
contain important safety and use information.
UNPACKING
The products in this kit have been thoroughly tested and have been shipped in
perfect operating condition. Carefully check the shipping carton for damage
that may have occurred during shipping. If the carton is damaged, carefully
inspect the device for damage, and be sure all accessories necessary to
install and operate the device have arrived intact. In the event that damage
has been found or parts are missing, please contact our customer support team
for further instructions. Please do not return this device to your dealer
without first contacting customer support. Please do not discard the shipping
carton in the trash. Please recycle whenever possible.
WARRANTY RETURNS
All returned service items, whether under warranty or not, must be freight
pre-paid and accompanied by a return authorization (R.A.) number. The R.A.
number must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be written
down on a piece of paper and included in the shipping container. If the unit
is under warranty, you must provide a copy of your proof of purchase invoice.
Items returned without an R.A. number clearly marked on the outside of the
package will be refused and returned at customer’s expense. You may obtain an
R.A. number by contacting customer support.
CUSTOMER SUPPORT
Contact ADJ Service for any product related service and support needs.
Also visit forums.adj.com with questions,
comments or suggestions.
ADJ SERVICE USA – Monday – Friday 8:00am to 4:30pm PST
323-582-2650 | Fax:
323-832-2941 |
support@adj.com
ADJ SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET
+31 45 546 85 60 | Fax: +31 45 546 85 96 |
support@adj.eu
REPLACEMENT PARTS please visit parts.adj.com
IMPORTANT NOTICE!
THIS UNIT CONTAINS NO USER SERVICEABLE COMPONENTS. DO NOT ATTEMPT ANY REPAIRS
YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES
RESULTING FROM MODIFICATIONS TO THIS DEVICE AND/OR THE DISREGARD OF SAFETY
INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY
AND ARE NOT SUBJECT TO WARRANTY CLAIMS AND/OR REPAIRS.
LIMITED WARRANTY (USA ONLY)
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products,
LLC products to be free of manufacturing defects in material and workmanship
for a prescribed period from the date of purchase (see specific warranty
period on reverse). This warranty shall be valid only if the product is
purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place
of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, you must obtain a Return Authorization number (RA#)
before sending back the product-please contact ADJ Products, LLC Service
Department at 800-322-6337. Send the
product only to the ADJ Products, LLC factory. All shipping charges must be
pre-paid. If the requested repairs or service (including parts replacement)
are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the
entire instrument is sent, it must be shipped in its original package. No
accessories should be shipped with the product. If any accessories are shipped
with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, or for the safe return thereof.
C. This warranty is void of the serial number has been altered or removed; if
the product is modified in any manner which ADJ Products, LLC concludes, after
inspection, affects the reliability of the product, if the product has been
repaired or service by anyone other than ADJ Products, LLC factory unless
prior written authorization was issued to purchaser by ADJ Products, LLC; if
the product is damaged because not properly maintained as set forth in the
instruction manual.
D. This is not a service contact, and this warranty does not include
maintenance, cleaning or periodic check up. During the period specified above,
ADJ Products, LLC will replace defective parts at its expense with new or
refurbished parts, and will absorb all expenses for warrant service and repair
labor by reason of defects in material or workmanship. The sole responsibility
of ADJ Products, LLC under this warranty shall be limited to the repair of the
product, or replacement thereof, including parts, at the sole discretion of
ADJ Products, LLC. All products covered by this warranty were manufactured
after August 15, 2012, and bear identifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes
in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to
any accessory supplied with products described above. Except to the extent
prohibited by applicable law, all implied warranties made by ADJ Products, LLC
in connection with this product, including warranties of merchantability or
fitness, are limited in duration to the warranty period set forth above. And
no warranties, whether expressed or implied, including warranties of
merchantability or fitness, shall apply to this product after said period has
expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or
replacement as is expressly provided above; and under no circumstances shall
ADJ Products, LLC be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to ADJ Products, LLC
Products and supersedes all prior warranties and written descriptions of
warranty terms and conditions heretofore published.
LIMITED WARRANTY PERIODS
-
Non L.E.D. Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
-
Laser Products = 1 Year (365 Days) Limited Warranty (excludes laser diodes which have 6 month limited warranty)
-
L.E.D. Products = 2-year (730 days) Limited Warranty (excluding batteries which have a 180 day limited warranty)
Note: 2 Year Warranty only applies to purchases within the United States. -
StarTec Series = 1 Year Limited Warranty (excluding batteries which have a 180 day limited warranty)
-
ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty
SAFETY GUIDELINES
To guarantee a smooth operation, it is important to follow all instructions and guidelines in this manual. ADJ PRODUCTS LLC is not responsible for injury and/or damages resulting from the misuse of these devices due to the disregard of the information printed in this manual. Only qualified and/or certified personnel should perform installation of these devices and only the original rigging parts included with these devices should be used for installation. Any modifications to these devices and/or the included mounting hardware will void the original manufacturer’s warranty and increase the risk of damage and/or personal injury.
| THERE ARE NO USER SERVICEABLE PARTS INSIDE THESE DEVICES.
DO NOT ATTEMPT ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S
WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS STAND AND/OR THE
DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE
MANUFACTURER’S
WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
---|---
| NEVER SET UP OR INSTALL STAND ON UNEVEN SURFACE!
NEVER INSTALL OR MOUNT STAND IN UNSTABLE LOCATIONS!
SPREAD THE LEGS UNTIL THE STAYS EXTEND HORIZONTALLY!
NEVER REMOVE THE SAFETY PIN WHEN THE A KNOB IS LOOSE!
BE CAREFUL NOT TO OVEREXTEND THE INNER PIPE!
KEEP FLAMMABLE MATERIALS AWAY FROM THE STAND
MAX LOAD CAPACITY PER STAND IS 100 LBS. (45.4 KGS)
| INDOOR / DRY LOCATIONS USE ONLY!
DO NOT EXPOSE DEVICES TO RAIN AND/OR MOISTURE!
| WHEN USING STAND OUTSIDE UNDER STRONG WIND, TAKE APPROPRIATE MEASURES
TO AVOID TIPPING!
TIGHTEN EACH KNOB AND BOLT SECURELY!
AVOID BRUTE FORCE WHEN INSTALLING.
ONLY USE RECOMMENDED RIGGING HARDWARE AS DESCRIBED IN THIS GUIDE.
USE THE ORIGINAL PACKAGING AND MATERIALS TO TRANSPORT FOR SERVICE.
| DO NOT POSITION STAND CLOSE TO ANY FLAMMABLE MATERIALS WHILE OPERATING.
DO NOT ATTEMPT INSTALLATION OF STAND IF YOU LACK THE RELEVANT KNOWLEDGE OR
EXPERTISE.
OVERVIEW
INCLUDED ITEMS
1. Knob A
2. Knob B
3. Knob C
4. Knob D
5. Stay
6. Leg
7. Outer Pipe| 8. Inner Pipe
9. Center Post
10. T-Bar
11. Slide Mount T-Collar
12. Truss I-Beam Section
13. I-Beam Support Bar
---|---
INSTALLATION INSTRUCTIONS
FLAMMABLE MATERIAL WARNING
Keep stand minimum 5.0 feet (1.5m) away from flammable materials and/or
pyrotechnics.
**** DO NOT INSTALL/HANG DEVICES ON STAND IF YOU ARE NOT QUALIFIED TO DO SO!
AVOID INSTALLING OR MOUNTING THE STAND IN UNSTABLE LOCATIONS, SUCH AS AN
UNEVEN SURFACE OR MOVING TABLE. DOING SO MAY CAUSE THE STAND TO TIP OVER AND
CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE.
WHEN USING THE STAND OUTSIDE UNDER STRONG WIND, TAKE APPROPRIATE MEASURES TO
PREVENT THE STAND FROM TIPPING OVER.
TIGHTEN EACH KNOB AND BOLT SECURELY. ENSURE THAT THE BRACKET HAS NO LOOSE
KNOBS OR JOINTS AFTER INSTALLATION TO PREVENT ACCIDENTS AND/OR INJURY.
AVOID PLACING THE STAND IN A DOORWAY OR OTHER HIGH TRAFFIC AREAS AS PEOPLE MAY
TRIP ON THE EQUIPMENT AND CORDS, OR BE INJURED BY FALLING OBJECTS.
TAKE CARE NOT TO PINCH YOUR FINGERS OR HANDS BETWEEN THE STAND LEGS.
NEVER STAND DIRECTLY BELOW THE DEVICES WHEN MOUNTING, REMOVING OR SERVICING.
DEVICES MUST ALL BE INSTALLED FOLLOWING ALL LOCAL, NATIONAL, AND COUNTRY
COMMERICAL ELECTRICAL AND CONTRUCTION CODES AND REGULATIONS.
DO NOT EXCEED WEIGHT CAPACITY OF 100 LBS (45.4 KGS) PER STAND (WHEN EVENLY
DISTRIBUTED).
SETUP
Loosen Knob D by turning it counter clockwise. Spread the legs by pulling up
on the outer pipe until the stays extend horizontally.
Loosen Knob C by turning it counter clockwise. Extend the inner pipe to the desired height and insert the safety pin through the stopper holes in the inner pipe. Secure and tighten Knob C by turning it clockwise. Repeat this process to set the desired height for the center post as well.
Assembling the Truss I-Beam
The stand comes with a Truss I-Beam for mounting optional lighting and
other equipment. To use the Truss, insert 2 I-beam connectors into one end of
the I-Beam Support. Insert the connector knobs through the I-Beam and fasten
with the wing nuts.
Assemble the Support Rod by inserting a Slide Mount T-Collar onto each end of
the Support Rod.
Slide the assembled Support Rod onto the I-Beam connectors.
Assemble the second half of the Truss I-Beam by inserting one end of the second Truss I-Bar onto the I-Beam connectors that were installed in the previous step. Insert the connector knobs through the I-Beam and fasten with the wing nuts.
Attaching the Truss I-Beam and T-Bar
Slide two Slide Mount T-Collars onto the center post of each stand. Insert one
end of the truss assembly into the Slide Mount T-Collars and place another
Slide Mount T-Collar on the very top of each stand’s center post.
Tighten the small knobs on the Slide Mount T-Collars at each end of the truss.
Slide a T-bar into each of the top Slide Mount T-Collars on the center posts
and tighten knobs to secure.
MOUNTING OPTIONAL LIGHTING AND OTHER ACCESSORIES
Lighting and other optional accessories may be mounted to the T-Bar as well.
For installation instructions, please refer to the mounting instructions
provided with the fixtures that are to be installed.
TROUBLE SHOOTING
The stand is unstable.
- Check to ensure that all knobs and hardware are tight and secure.
- Reposition the stand if it is located in an unsuitable location (uneven or unstable surface).
- Additional measures (i.e. sandbags or security cables) may be needed to secure the stand.
FREQUENTLY ASKED QUESTIONS
What are the dimensions of the T-Bar?
The dimensions are .4 x 1.57 x 47.2” (20 x 40 x 1,200 mm).
What is weight capacity of the stand?
Each stand has a weight capacity of 100 lbs. (45.4 kg) The weight capacity of the system is 200 lbs. (90.7 kg) when evenly distributed.
What is the diameter of the T-Bar?
The T-Bar is 20 x 40 mm with a diagonal of 44.7mm (1.76”)
What is the maximum height of the stand?
The minimum extended height is 57.1” (1,450) while the maximum extended height of the stand is 118.1” (3,000 mm.)
Are additional stands, clamps or accessories available?
Yes. A variety of stands and accessories are available at www.adj.com.
SPECIFICATIONS
- 100% portable trussing system
- Easy set up and high stability
- Features 2 Black steel tri-pods which extend up to 9 ft.
- 2 added T-Bars on top to hang more lights.
- Two 5ft. truss I-Beams that fit together to create a 10ft. trussing span
- Ideal for Mobile DJs and bands
- Includes locking pins and hardware
- System Capacity: 200 lbs. (evenly distributed)
- T-Bar Diameter: 1.5-inch
- Truss Diameter: 1 1/2”
- Weight: 45 lbs.
OPTIONAL ACCESSORIES
| ORDER CODE | DESCRIPTION |
|---|---|
| EVE100 | Single sided white speaker stand scrum, 5 ft, includes carrying bag |
| EVE200 | 2 sided white speaker stand scrum, 5 ft, includes carrying bag |
| EVE300 | 3 sided white speaker stand scrum, 5 ft, includes carrying bag |
| OSL587 | O Slim 2 Clamp (Pearl) |
| OSL150 | O Slam 1.5 Clamp |
DIMENSIONAL DRAWINGS
Documents / Resources
| ADJ
LTS 50T AS Portable Trussing
System
[pdf] User Manual
LTS 50T AS Portable Trussing System, LTS 50T AS, Portable Trussing System,
Trussing System
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>