Whitehall T-12-M-CC CleatPRO Mobile Cleast Steamer Instruction Manual

June 6, 2024
Whitehall

OPERATION AND CARE OF

Division of Acorn Engineering Company®

Instructions for Operation of cleatPRO Steamer®

Congratulations on receiving your cleat Steamer®
Your Steamer is a simple and trouble-free unit to operate. The tank body, lid, bottom, and tank housing are all made from type 304 stainless steel. The controls are an  ON/OFF switch on the front of the unit and a thermostat on the rear to control the water temperature. Unit is preset to a normal operating temperature.
Side handles and a handle on the lid minimize contact with the hot surface. Inside the unit are a heating element and a temperature sensor. Side handles and locking casters below allow easy movement of the unit. A drain valve is located on the back of the unit.
Model T-12-M-CC
100-120 Volts, 50/60 Hz,
15 Amps
Model ET-12-M-CC
200-240 Volts, 50/60 Hz,
6 Amps

WHITEHALL MANUFACTURING •P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A Phone 800-782-7706626-968-6681 • Fax 626-855-4862 • Web: www.whitehallmfg.com

Model T-8-S-CC
100-120 Volts, 50/60 Hz,
15 Amps
Model ET-8-S-CC
200-240 Volts, 50/60 Hz,
6 Amps

FOR TECHNICAL ASSISTANCE CONTACT WHITEHALL MANUFACTURING

Instructions for Operation of cleatPRO Steamer®

Model T-4-S-CC
100-120 Volts, 50/60 Hz,
8.33 Amps

Instructions for Operation of cleatPRO Steamer®

FILLING your unit

|
---|---
1 Make sure the unit is unplugged and all packaging has been removed.| 2 Check the drain valve before filling. Use the hose provided. Fill the unit with 2” of tap water for Model T-12-M-CC and 1-1/2” for Model T-8-S-CC.

NOTE: ENSURE WATER LEVEL IS MAINTAINED

|
---|---
3. Place the cleat rack inside the unit. Be careful of the heating element.| 4 Insert shoes carefully into the unit.

NOTE: WHEN IN USE ENSURE THE LID REMAINS CLOSED SO STEAM DOES NOT ESCAPE.
The water temperature for normal operating conditions is about 165°F (74°C). The thermostat is very sensitive; even a small adjustment can raise or lower the temperature several degrees. The thermostat has an adjustable temperature range of 65°F (18°C) to 175°F (79°C) ±5°F (-15°C). To adjust the temperature, you need a Thermometer capable of 180° F (83° C).

5 Facing the back of the unit, find the metal temperature stem between the 2 screws in the lower middle of the unit. Attach knob.
6 Using the knob, turn clockwise to increase the temperature. Allow the temperature to stabilize, and measure the water temperature with the thermometer.
CAUTION: Sensitive thermostat – a small adjustment changes several degrees. Temperature range of 65°F (18°C) to 175°F (79°C) ±5°F (-15°C).

MANUFACTURER’S WARRANTY

Whitehall Manufacturing Company warrants that its products are free from defects in material or workmanship under normal use and service for a period of one year from the date of shipment. Whitehall’s liability under this warranty shall be discharged solely by replacement or repair of defective material, provided Whitehall is notified in writing within one year from the date of shipment, F.O.B. Industry, California.
This warranty does not cover installation or labor charges and does not apply to materials that have been damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Whitehall under this warranty. Whitehall shall not be liable under any circumstances for incidental, consequential, or direct charges caused by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all other warranties expressed or implied. Product maintenance instructions are issued with each fixture, and disregard or non-compliance with these instructions will constitute an abnormal use condition and void the warranty. Stainless steel must be properly maintained after the water has been introduced into the fixture, or Whitehall’s limited warranty is void. If you have any questions or require technical assistance, please call 800-743-8219.
NOTICE TO KEEP ORIGINAL PACKAGING – Regarding warranty claims: customer must retain the original packaging for one year upon receipt of product. If the packaging is discarded, it is the customer’s responsibility to provide adequate packaging. Any shipping claims that are a direct result of customer- provided packaging materials will be handled by the shipper.

 Mailing Address:
P.O. Box 3527 • City of Industry, CA 91744-0527 U.S.A
Physical Address:
15125 Proctor Avenue • City of Industry, CA 91746 U.S.A
Phone 800-782-7706626-968-6681
Fax 626-855-4862
Web: www.whitehallmfg.com
E-mail: info@whitehallmfg.com
Member of MORRIS GROUP INTERNATIONAL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals