Whitehall WH3779 Ligature Resistant Corterra Ada Compliant Dual Basin Vanity Instruction Manual

Important: Some options may slightly alter installation. To ensure proper installation review the manual thoroughly and verify rough-ins before beginning any work. File this manual with the owner or maintenance personnel upon completion of installation. Industry standard wall backing, for wall hung fixtures, is required. Installer provided wall anchors and wall anchoring hardware must be appropriate for wall construction. ANSI, UFAS or ADAcompliance is subject to the interpretation and requirements of the local code authority and is the responsibility of the installer for verification. Single Temp Valve Assembly: Recommended working water pressure is 30 psi (2.07 bars) minimum to 100 psi (6.89 bars) maximum. Maximum temperature is 130°F (54.4°C). Maximum outlet temperature recommended is 105°F (40.6°C). Valve assembly must be drained prior to being subjected to freezing temperatures. Acheckstop is provided with this valve assembly. T/P Mixing Valve Assembly: Recommended working water pressure is 30 psi (2.07 bars) minimum to 100 psi (6.89 bars) maximum. Maximum hot water temperature is 180°F (82°C). Temperature adjustment range is 85-115°F (29-46°C). Minimum hot water supply temperature must be 5°F (3°C) above desired set temperature. Valve assembly must be drained prior to being subjected to freezing temperatures. The valve assembly has checks integral to the inlets however, angle stops are to be provided by the installer. Prior to installation, supply lines must be flushed of all foreign material such as pipe dope, chips, or solder. Debris or foreign material in water supply may damage valve. Teflon tape is recommended on all threaded waste and supply connections to reduce the possibility of leaks. Provide 110-120VAC/60Hz/3A (MAX) electrical receptacle for optional factory supplied 120VAC/9VDC, 100mAplug-in transformer.
NOTE: Receptacle(s) must be wired to a GFCI protected circuit. Fixture must be earth grounded per N.E.C. (National Electrical Code).

ACCESSIBILITY OVERVIEW

DIMENSIONAL DATA

ROUGH-IN DIMENSIONS -ADA (Adult) And OBC Ontario Building Code (Canada)

NOTE: Fixture Weight is approximately 200 LBS (91 KGS)

VIEW FROM FRONT OF FIXTURE

A 9/16″ Diameter Mounting holes (12) Places for Mounting Frame, Recommended 3/8″ UNC Hardware, Provided by Installer, Wall Anchor with a Minimum Pull-Out Force of 1,000 lbs Per Local Codes at Locations Shown.

B 9/16″ Diameter Mounting holes (4) Places for Mounting Frame, Recommended 3/8″ UNC Hardware, Provided by Installer, Wall Anchor with a Minimum Pull-Out Force of 1,000 lbs Per Local Codes at Locations Shown.

C 1-1/2″ O.D. Tube Lavy Waste Outlet for Compression Joint.

D 1/2″ NPS Hot & Cold Supplies for Angle Stops (By Others).

E 1/4″ Diameter Mounting Holes (11), Wall Anchors and Anchoring Hardware Provided by Installer.

F 120VAC, 60Hz, 3A (Max) GFCI Protected, Electrical Receptacle for Optional Electronically Operated Faucets

ROUGH-IN DIMENSIONS – ADA AGES 6 THRU 12 YEARS

NOTE: Fixture Weight is approximately 200 LBS (91 KGS)

VIEW FROM FRONT OF FIXTURE

A 9/16″ Diameter Mounting holes (12) Places for Mounting Frame, Recommended 3/8″ UNC Hardware, Provided by Installer, Wall Anchor with a Minimum Pull-Out Force of 1,000 lbs Per Local Codes at Locations Shown.

B 9/16″ Diameter Mounting holes (4) Places for Mounting Frame, Recommended 3/8″ UNC Hardware, Provided by Installer, Wall Anchor with a Minimum Pull-Out Force of 1,000 lbs Per Local Codes at Locations Shown.

C 1-1/2″ O.D. Tube Lavy Waste Outlet for Compression Joint.

D 1/2″ NPS Hot & Cold Supplies for Angle Stops (By Others).

E 1/4″ Diameter Mounting Holes (11), Wall Anchors and Anchoring Hardware Provided by Installer.

F 120VAC, 60Hz, 3A (Max) GFCI Protected, Electrical Receptacle for Optional Electronically Operated Faucets

FRAME ANCHORING

Strike a horizontal chalk line on finished wall to indicate required deck height, based off dimensional drawing on 1pages 4 and 5. Strike a vertical chalk line to indicate centerline of basins. Align bottom frame assembly 1 horizontal notches 2 with horizontal chalk line and vertical 3 with vertical chalk lines. Mark for and install wall anchors 4, provided by installer (12 places). Anchor bottom frame assembly 1 to wall using installer provided 3/8” UNC mounting hardware 5.

NOTES:

1. Frame Assembly
2. Horizontal Notched (Rim Height)
3. Vertical Notches ( Basin Center Lines)
4. Installer Provided Wall Anchors (Wall Anchor with a Minimum Pull-Out Force of 1,000 lbs)
5. Installer 3/8” UNC Mounting Hardware

FIXTURE ASSEMBLY

Prior to installing the deck 1 to the frame 2 the bottom cover 3 must be removed. Unscrew the #10-32 UNF 2 screws 4 and remove bottom cover 3. Locate bottom cover 2 and Screws 3 in a secure place so they do not get lost or damaged.

HINT: It may be advantages to install deck trim such as faucets, soap dispensers or other accessories prior to wall mounting.

Push the Deck Assembly 1 against the wall and push down until the Deck Assembly 1 rest on top of the Frame 3 Assembly 2 and the Deck Angle 5 engages into the Frame clip 6. Secure Deck Assembly 1 to Frame assembly 2 using provided 1/4”-20 hardware 7. See Details A and B

Push the Deck Assembly 1 against the wall and push down until the Deck Assembly 1 rest on top of the AFrame Assembly 2.

HINT: It may be advantages to install deck trim such as faucets, soap dispensers or other accessories prior to wall mounting.

Secure Deck Assembly 1 to Frame assembly 2 using provided 1/4”-20 hardware 7. While attaching Deck BAssembly 1 to Frame Assembly 2 install Valve Mounting Bracket 8 on the end Frame Angles as shown.

WASTE ASSEMBLY

HINT: Teflon tape is recommended on all threaded waste and supply connections.

Install strainer to basin using plumbers putty 4on underside of grid strainer flange. From beneath basin, assemble gasket, washer and jam nut as shown to strainer and tighten securely. Add close elbow to strainer assembly as indicated.

1. Strainer w/ 1-1/2″ -16 UNE Threads
2. Rubber Gasket (1) required
3. Flat Fiber Washer (1) required
4. 1-1/2″-16 x 1-1/4″ UNI Close Ell with 3/8″ NPT Clean-Out Plug
5. Waste Outlet Connection

NOTE: Waste Assembly may be provided with Extra items not required in this assembly.

NOTE: Waste assembly may require field cutting and fitting by the installer.

Assemble waste piping using TEFLON tape on all threaded connections and make up waste connections 4 to 1-1/2″ P-trap.

VALVE INSTALLATION

FOR OPTIONAL BEST-CARE FAUCET

Remove screws 1 from Valve Mounting Bracket 1 A 2. Hold Valve Assembly 3 against Mounting Bracket 2 and secure with Screws 1.

Before making up the supply connections, the supply lines must be flushed of all foreign material such as pipe dope, pipe chips, solder, sand, etc.

VALVE INSTALLATION & ADJUSTMENT

Valve Assembly Installation:

NOTE: Installation should be in accordance with accepted plumbing practices.

1. Locate suitable place for mounting the valve assembly. Valve assembly should be accessible for service and adjustment and as close to the point-of-use as possible. Wall anchors and anchoring hardware are by others.
2. Connect hot and cold water to supply valve using 1/2” NPTE connections.
3. Connect outlet of tempering valve to spout(s) using 1/4” O.D. tube connections provided.
4. Turn on hot and cold water supplies. If any leaks are observed, hand tighten connections as necessary to stop leaks before proceeding.
5. Turn on fixture and allow water to flow for 2 minutes. Measure water temperature at outlet. If water is not at desired temperature, adjust as necessary.

Temperature Adjustment:

NOTE : Factory set temperature is 105º F

1. Loosen locknut.
2. Turn on fixture and run water for at least 2 minutes. Allow supply temperature tostabilize.
3. Turn temperature stem counter-clockwise for hotter or clockwise for colder outlet temperature.
4. Tighten locknut to prevent accidental or unauthorized temperature adjustment.
5. Re-check outlet temperature.

FAUCET CONNECTIONS

Leave a minimum 1/4” of polyethylene tubing through the Ferrule Nut on the pushbutton assembly. This is necessary to ensure proper tubing connection.

SENSOR OPERATION & CONNECTIONS FOR OPTIONAL BEST-CARE FAUCET

NOTE: Shown with optional Best-Care “L” Series Faucet for reference only. Refer to specified Faucet installation details for more information. Valve Assembly locations shown are for schematic only. Refer to installation details for valve placement

-SO Sensor Operation Range Adjustment

1. Make sure power supply is disconnected from sensor and make short circuit on red wires. See DETAIL A.
2. Connect power supply to sensor. Red light should be flashing.
3. Move hand in front of sensor to distance of 2” to 4” within 5 seconds and wait until red light flashes quickly.
4. Move hand to desired sensing distance. See DETAIL B.
5. Hold hand at desired sensing distance until red light stops flashing and solenoid activates. See DETAIL C.

WH3377L-PPZ Programmable Piezo Pushbutton (Shown)

Transformer must be plugged into a GFI protected circuit. Fixture must be earth grounded per N.E.C. or applicable codes.

ACCESS PANEL INSTALLATION

With Deck 1 secured to frame 2 re-install bottom Cover 3 with #10-32 UNF Screws 4.

HINT: Prior to installing Trap Enclosure it is recommended to operate valve and ensure there are no leaks present and everything functions correctly.

Install p-trap cover using #10-32 x 1/2” center reject hex head screws provided. 6 Secure bottom of p-trap cover to wall with anchoring hardware (by others)

TROUBLE SHOOTING FOR OPTIONAL PUSHBUTTON OPERATED VALVES

CONDITION: WATER DOES NOT FLOW

fitting.
Pushbutton air diaphragm leaks.| Replace pushbutton air diaphragm.
Servomotor diaphragm center hole is blocked| Remove blockage
Servomotor upper diaphragm is damaged.| Replace servomotor upper diaphragm.

CONDITION: WATER DRIPS, WON’T SHUT OFF

CONDITION: REDUCED WATER FLOW

cleaning solution.

CONDITION: PREMATURE WATER SHUT OFF

fitting.
Pushbutton air diaphragm leaks.| Replace pushbutton air diaphragm

CARE, CLEANING, AND REPAIR OF CORTERRA SOLID SURFACE

CORTERRA SOLID SURFACE
Acorn’s densified solid surface material is composed of recycled solid-surface polymer resin, aluminum trihydrate and fillers. It is resistant to stains, impact and burns and complies with ANSI Z124.3. It is attractive, durable and easy to maintain.

ROUTINE CLEANING
Corterra should be kept clean at all times. If maintained, Corterra surfaces will retain their new, clean appearance indefinitely. Wash with a non-abrasive all purpose cleaner and water, then rinse. Wipe dry. (Never use cleaners with strong chemicals such as toilet bowl cleaners, rust removers, ceramic cook top cleaners, laquer thinners or oven cleaners). To remove persistent stains use a Scotch Brite pad and an abrasive cleaner or a solution of household bleach and water (1 part water to 1 part bleach).

REPAIRING SURFACE DAMAGE
Surface damage, such as minor chips, scratches, burn marks and graffiti can be repaired with a fine grit abrasive cleanser, such as a Scotch-Brite pad or fine grit sandpaper. For more serious physical damage caused by vandals, an Acorn Solid Surface Repair Kit is available. Contact the factory for details. Refer to drawing #9927-160-002.

CARE AND CLEANING OF STAINLESS STEEL SURFACE

NORMAL CLEANING
Clean weekly or more often, as needed (especially high polishing surfaces)

RECOMMENDED CLEANING MATERIALS

• Sponge – natural or artificial
• Nylon or other soft-bristle material brush
• Soft cloth (as used on automobile finishes)

RECOMMENDED CLEANING SOLUTIONS

• Hand dishwashing liquid/soft water solution
• Mild soap/soft water solution
• 3M Stainless Steel Cleaner/Polish
• White vinegar/soft water solution (for brightening, removing oil and hard water deposits)
• CLR Brand Cleanser or baking soda/soft water solution (for brightening, removing hard water deposits)
• Club soda and sponge

FOR HIGH POLISH STAINLESS STEEL
Note: High polish stainless steel surfaces should never come into contact with any abrasive cleaning brush, cloth or cleaning agent. To remove smudges and fingerprints: Wipe surfaces with a quality Stainless Steel Cleaner/Polish. Apply using a soft non-abrasive cloth, wipe surfaces with stainless steel cleaner/polish.

To remove rust stains:
Wipe surfaces with CRES (available from Acorn) or equivalent cleaner. Use recommended solutions. Apply using a soft non-abrasive sponge. Rinse surfaces immediately after application. Always follow cleaner product directions provided. Afterwards, using a soft, non-abrasive cloth, wipe surfaces with stainless steel cleaner/polish.

FOR TOUGH PROBLEMS

• CRES Cleaner specifically for rust stains (available from Acorn)
• Tarn-X for general stains

• 7 chrome polish

• Silver polish

To remove stubborn spots or to treat a scratch (Standard Satin Finish Only):
Use of synthetic, abrasive, general-purpose pads such as Scotch Brite is recommended. Apply the stainless steel cleaner/polish to the synthetic, abrasive pads and CAREFULLY rub out spot with cleaner/ polish. Be sure to rub in the direction of the grain! Do not allow steel wool to come in contact with the stainless steel. Steel particles can embed into the stainless steel surface and create rust! Stainless steel should be kept clean at all times. If maintained, stainless steel surfaces will retain their new, clean, polished appearance indefinitely. To remove water spots or rust spots, stainless steel cleaner/polish on a cloth is recommended.
IF SPOTS ARE STUBBORN OR IF YOU WISH TO TREAT A SCRATCH: synthetic, abrasive, general-purpose pads such  as Scotch Brite are recommended. Apply the stainless steel cleaner/polish to the synthetic, abrasive pad and CAREFULLY rub out spot with cleaner/polish. Be sure to rub in the direction of the grain! Do not allow steel wool to come in contact with stainless steel. Steel particles can embed into the stainless steel surface and create rust.

COMPONENTS & REPAIR PARTS

VALVE
-WH3377L-PPZ
-WH3377L-WSF-SO
-WH3375L-WSF-SO Optional Electronic Metering Valve Assembly, Single Temperature| 2590-905-001|
-WH3377L-PPZ-MXTP
-WH3377L-WSF-SO-MXTP
-WH3375L-SO-MXTPOptional Electronic Metering Valve
Assembly, Single Temp, TemperaturePressure Balancing Mixing Valve, ASSE
1070 Compliant| 2590-906-001|
-WH3377L-PPZ Optional Electronic Metering Valve
Assembly, Hot and Cold| 2590-915-001|
-WH3377L-PPZ-MXTP Optional Electronic Metering Valve Assembly,
Hot and Cold, Temperature-Pressure Balancing
Mixing Valve, ASSE 1070 Compliant| 2590-916-001|

References

• Healthcare Products with Universal Design - Whitehall Mfg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>