Jennov 15493419 HD WiFi Security Camera User Guide

October 27, 2023
JENNOV

Jennov 15493419 HD WiFi Security Camera User Guide

Jennov 15493419 HD WiFi Security Camera.JPG

Be sure to read this book before installing or using the surveillance camera.
Keep the book in a safe place so that you can read it whenever necessary.

Please read carefully before use it

www.jennov.com

support@jennov.com

What’s Included

FIG 1 What's Included.JPG

Cloud Edge App installation and Setup
Search “Cloudedge” on apple store or google play to download the app.

  • from Google play
  • from Apple store
  • or Scan the following QR code

FIG 2 Cloud Edge App installation and Setup.JPG

Download App ( IOS/ Android )

Product overview

FIG 3 Product overview.JPG

FIG 4 Product overview.JPG

CAUTION: Please insert the Micro SD Card according to the direction shown in the diagram. Micro SD Card might JAM if inserted incorrectly and device could be damaged.

SD Card Port: Support micro SD card for local storage (Max 128GB).
Reset button: Used to restore the camera to factory settings (Press and hold on5-8s).
Card capacity requirements: 8-128GB.
Read and write speed requirements: Class10 level.
File format: FAT32.

Installing Camera

Select height and location

Install the camera 7-10 ft (2-3m) above the ground.This height maximizes the detection range of motion sensor of the camera. Avoid placing camera direct to sunlight.

FIG 5 Installing Camera.JPG

Tips:

  1. Avoid placing the camera in direct sunlight.
  2. It is not recommended to use the power extension cable connect the camera.
  3. Before installing the camera, please match the WiFi at home before installation.
  4. The camera must be installed in a 90 degree straight line, and other installation methods such as upside down, tilt, etc. are not allowed.
  5. When installing the camera, try not to look at any place with strong light source. For example, street lights, glass, sun, green plants within 7-10ft will directly affect the definition and night vision effect of the camera.

Installation

  1. Drilling according to position sticker, drill bit:15/64 (6mm)
  2. Insert the plugs
  3. Tighten the screw

FIG 6 Installation.JPG

Test the Wifi signal at installation position
Use cell phone to test Wifi signal quality at the installation position before installing camera, make sure the Wifi router can provide good Wifi signal.

FIG 7 Test the Wifi signal at installation
position.JPG

APP Sign Up

The Cloudedge app that is necessary to operate the camera.
Signing up for storage in the cloud is totally optional and is really not necessary when using an onboard Micro SD card .

  1. Open the APP to sign up an account. Go to the login interface, and click “Sign UP”.
  2. Sign up with your email address, and click “Next”.
  3. Set up an “Nickname” and “Password” for your APP, click “Done” to complete.

FIG 8 APP Sign Up.JPG

Set up Wifi for the camera

1. Bring both your mobile phone and your camera close to your router (max distance of 5 meters/16 feet).

Note: The camera can only connect to a 2.4 GHZ Wifi signal. It does not support using a 5 GHZ signal. Therefore, please ensure you connect to a 2.4 GHZ signal on your network as shown in the below illustration.

FIG 9 Set up Wifi for the camera.JPG

FIG 10 Set up Wifi for the camera.JPG

2. Log in to “Cloudedge”, then tap the “+” icon in the center. Tap “Camera” to add device.

FIG 11 Set up Wifi for the camera.JPG

3.Reset device and wait for a flashing RED indicator light, then tap “Next”
4.Select the Wi-Fi needs to be connected (Wi-Fi in your house), enter the password, and click “Next”.

FIG 12 Set up Wifi for the camera.JPG

Note: Please don’t set too many special symbols for your WiFi password, which may cause the device to be unrecognized and fail to add.

5. Use the camera to scan the QR code on your mobile phone as noted below. When the scan is complete you will hear a prompt tone then push Next.

FIG 13 Set up Wifi for the camera.JPG

FIG 14 Set up Wifi for the camera.JPG

FIG 15 Set up Wifi for the camera.JPG

Functions Introduction and Settings

1. Functions Introduction

FIG 16 Functions Introduction.JPG

Functions Introduction and Settings
Screenshot: Save the screenshot of the current picture in the mobile phone.
Intercom: Press and hold intercom to realize two-way audio.
Video Recording: This video needs to be recorded into the mobile phone memory.
Motion Detection: When this function is enabled, the video or mobile phone will get message alarm push when any moving object is detected.
PTZ: It controls the camera to rotate up, down, left and right.
Lens Switch: Turn on and off the viewable monitoring screen (usually used to share users).
Photo Album: The contents of screenshots can be viewed here.

2. Motion Detection Video and All Day Video

FIG 17 Motion Detection Video and All Day Video.JPG

  1. All Day Video Recording: 24-hours video recording. When there are moving objects, the video format will become dark blue. When there is no one else, the video format is light blue.
  2. Motion Detection Video Recording: When there is a moving object, the recording format will change to dark blue, and other times it is in standby mode. The recording time of motion detection can be set. The default is 1 minute. (three modes of 1, 2, 3 and minute can be set).
    Please see the next page for details.

Note: Motion detection video should be set preferentially in alarm settings.

3. Alarm Management

FIG 18 Alarm Management.JPG

Alarm On:
Enter system settings – alarm management – motion detection – enable motion detection, select the appropriate sensitivity, and it is recommended to default.

Alarm working mode:
The saving time of alarm video is 1 minute by default. (three modes of 1, 2, 3 and minute can be set)

Alarm Area:
Alarm Area: You can select the area need to be alarm. If checked, the alarm will be triggered when an object enters or exits the set alarm area.

Audible And Visual Alarm On:

  1. Audible Alarm: When moving or human shape is detected, the camera will give an audible alarm.
  2. White Light Alarm: When moving or human shape is detected, the camera will give a light alarm.
  3. Audible And Visual Alarm: When moving or human shape is detected, the camera will give audible and visual alarm.

Note: The audible and visual alarm is valid only at night.

4. Recording Time Selection

FIG 19 Recording Time Selection.JPG

Alarm Working Mode:
The saving time of alarm video is 1 minute by default. (three modes of 1, 2, 3 and minute can be set)

The recording time of motion detection can be set. The default is 1 minute. (three modes of 1, 2, 3 and minute can be set).

5. Image Settings

FIG 20 Image Settings.JPG

Image Setting: You can also set the flip of the screen according to the installation environment.

Night Vision Mode:

  1. Automatic: Default daytime is color and nighttime is infrared mode.
  2. Daytime: (full-color mode), color during daytime, the infrared light will not turn on at night, nor will the white light turn on.
  3. Nighttime: (black and white image), color during daytime, infrared will turn on at night (black and white image)

6. Share Device:

FIG 21 Share Device.JPG

Share Device:
Enter Settings – Select device sharing – after entering, there is a short video tutorial, or you can click add directly.

Share by scanning QR code or entering account.

Note:

  1. The accounts to be shared also need to download the app “cloudedge” to register.
  2. The one who was shared has only partial permissions to operate the device.
  3. Sharing can support up to 4 devices to watch at the same time.

7. Delete Device:

FIG 22 Delete Device.JPG

  1. In the viewing interface, long press the device interface, and a prompt will pop up. Click delete.
  2. Enter the settings – pull down to the bottom, and click delete.

FAQ

Q: How many device can be shared to others ?****

A: Max up to 4 device online viewing at the same time.

Q: The device cannot be previewed properly ?

A: Check whether the network is normal, you can place the camera close to the router, and if not, it is recommended to reset the device and add it again.

Q:How many device can be shared to others ?

A:Max up to 4 device online viewing at the same time.

Q: Why is it still in the list of devices after reseting?

A: The reset device only resets the network configuration of the camera, but cannot change the configuration on the App, remove the camera, and must be deleted by the App.

Q: How to “connect” the camera to another router?

A: First remove and reset the device on the App and then configure the device again by the App.

Q: Why doesn’t the device identify the SD card?

A: It is recommended that the SD card be inserted when the power to the camera is off and that it is fully inserted correctly. Make sure the SD card has been formatted with FAT 32. If not, this can be done via the Cloudedge app.

Q: Why can’t I receive notifications via the mobile phones app?

A: Please confirm that the App has been running on the phone, and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been opened.

Safety Statement

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and ( 2 ) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the equipment into anoutlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure Statement

The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm

Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

Warranty Tips

Please fill in the following information or scan QR code to activate the free 12-month warranty from the order date on.

After finish filling or scanning, please take a picture and send it to the email(support@jennov.com).

Then your free warranty will take effect !
During the warranty period, if any parts of product are damaged, please contact us immediately and we will provide satisfactory resolution.

Order Date:
Order Number/ID:
Buyer E-mail:
Buyer Tel:

Contact us

www.jennov.com
support@jennov.com
U.S Hotline: +1 3239021978

Free Warranty

Read More About This Manual & Download PDF:

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals