CLIM ART 605085 In Channel Incredibly Durable Rain Guards Installation Guide

June 14, 2024
Clim Art

INSTALLATION MANUAL

CLIM ART 605085 In Channel Incredibly Durable Rain
Guards

SIDE WINDOW DEFLECTORS

Before installing the deflectors, please read the manual.
Incorrect installation of deflectors can cause danger or injury.

COMPLETE SET

4(2) Piece Set (the product may differ from the illustration in the instructions)

CLIM ART 605085 In Channel Incredibly Durable Rain Guards - Complete
Set

  1. Front DriverSide Window Deflector

  2. Front Passenger Side Side Window Deflector

  3. Rear Driver Side Window Deflector

  4. Rear Passenger Side Window Deflector

  5. Instruction manual

  6. Plasticblade
    (1 piece)

  7. Alcohol wipe
    (2pieces)

ATTENTION! IMPORTANT INFORMATION!
ATTENTION! Read the installation instructions carefully and follow all POINTS in the text!
Incorrectly installed deflectors can be dangerous.If in doubt, please contact Clim Art.

  • Ifthe safety features of the vehicle do not allow youto close the window, deactivate them (check the car instruction manual)
    After installing the deflectors, leave the car windows closed for 72 hours. f the temperature s below 62.5°F/17°C, leave closed at minimum 24 hours and longer if possible.

  • We strongly recommend installing the deflectors at temperatures between S°F/15°C and 77°F/25°C.
    IMPORTANT INFORMATION! Clezn the grease off the installation surface with a supplied alcohol wipe. If the deflector installa- tion process is not followed, the manufacturer does not guarantee reliable fixation of the product.

THE TERMS USED IN THIS INSTRUCTION MANUAL

CLIM ART 605085 In Channel Incredibly Durable Rain Guards - The
Terms

  1. Deflector frame
  2. 2-Back part of deflector
  3. Front part of deflector

CLIM ART 605085 In Channel Incredibly Durable Rain Guards -
Attention

ATTENTION! Protective film, DO NOT REMOVE!

  1. FRONT DEFLECTORS
    CLIM ART 605085 In Channel Incredibly Durable Rain Guards - Front
Deflectors

  2. REAR DEFLECTORS
    CLIM ART 605085 In Channel Incredibly Durable Rain Guards - Rear
Deflector

FRONT DEFLECTORS
ATTENTION! Clean the installation surface with a supplied alcohol wipe. If the deflector installation process is not followed, the manufacturer does not quarantee the secure installation of the product.

1.1| Make sure the car windows are clean and dry.
Next,lowr the side windows completely and clean  the grease off the inner surface of the window channel with an alcohol wipe.| 1.2| Remove the protective liner from the tape on the deflector.
---|---|---|---
1.3| Place the front section of the deflector on the lower frame of the window as shown in the illustration.| 1.4| Shift the deflector forward, fitting the deflector frame  into the channel completely. Make sure the deflector is placed above the lower window frame.
1.5| Bending the center part of the deflector  utwards,
insert the rear section of the deflector into the channel, leaving a gap aboveiit.| 1.6| Starting with the front section of the deflector, insert it into the window channel.
1.7| Immediately after installing the deflector, adjust
its position by carefully pulling it outwards.| 1.8| To ensure the best installation of the deflector and the best adhesion between the tape and the surface of the rubber seal, itis strongly recommended that you use the plastic blade, moving it slowly between the window’s
inner rubber seal and the deflector.
1.9| Raise the window until it touches the deflector. Carefully pulling the deflector outwards, roll up the window with abrupt movements. Repeat this action 4-5 times, then leave the window closed.| 1.10| Repeat points 1.1 to 1.9 on the opposite side of the vehicle.

REAR DEFLECTORS
(FOR FOUR-DOOR VEHICLES)

2.1| Make sure the car windows are lean and dry. Next, lower theside windows completely and lean the  rease ofthe inner surface of the window channel  with an alcohol wipe.| 2.2| Remove the protective liner from the tape on the deflector.
---|---|---|---
2.3| The deflector must be installed starting at the rear.  To do so, place the rear section of the deflector  frame into the channel and move the front section  upwards. Position the entire deflector frame into the window channel.| 2.4| Immediately after installing the deflector, adjust its position by carefully pulling it outwards.
2.5| Toeensure the best installation of the deflector and  the best adhesion between the tape and the surface  of the rubber seal, it isstrongy recommended thatyou se the lasticblade, moving it slowly between  the window’s inner rubber seal and the  deflector.| 2.6| Raise the window until it touches the deflector.
Carefully pulling the deflector outwards, roll up the window  with abrupt movements, Repeat this action 4-5times, then  leave the window closed.
2.7| Repeat poits 1026 on te oppositside o the vehide.

CONGRATULATIONS!
Your unique and durable deflectors are installed to give you joy!
From this moment on we hope you enjoy their appearance!
If you have any questions about warranty, technical aid or requests for missing (lost) parts, do not hesitate to contact
Customer Service: by phone: + 1888 31111 25, by email: customerservice@sparklinesinc.com.
+We are glad to work for you and your vehicle to produce high quality products, which have ideal fit, easy installation
and enjoyment with everyday use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals