SOUNDPEATS MAC2 Bluetooth Headset User Guide

MAC2 Bluetooth Headset
User Guide

First Start

1. Open the charging case lid and toke out both earbuds, then remove the insulating film and put them back. Press and hold the button on the charging case for 3 seconds until the white lights flash twice, the earbuds enter pairing mode.
2. Activate the Bluetooth on your device and choose SOUNDPEATS Mae2″ to connect

Reset

1. Place back both earbuds, the white lights inside the charging cote flash slowly. the earbuds start charging
2. With the case lid open, press and hold the charging case button for 10 seconds until the white lights inside the Cose flash 3 times. reset complete
3. Close the case lid and reopen it to activate the earbuds

Weaning

1. Identify the left and right earbuds.
2. Rotate earbuds and find the most comfortable position.

Product Diagram

Control

Power On| Auto: Open up the case lid
Manually: Press and hold the MFB for 1.5s
---|---
Power Off| Auto:
1)Place back into the charging case and close the lid
2)Automatically power off after 3mins no connection Manually: Press and hold the MFB for Los
Play / Pause| Double-tap the MFB
Volume –| Single tap the left MFB
Volume +| Single tap the right MFB
Previous Track| Press and hold left MFB for 1.5s
Next Track| Press and hold right MFB for 1.5s
Answer / Hang Up Phone Call| Double-tap the MFB
Reject Phone Call| Press and hold the MFB for 1.5s
Switch Between Two Calls| Press and hold the MFB for 1.5s
Manually Enter Pairing Mode| Press and hold the button on the charging case for 3s
Activate Voice Assistant| Triple tap the right MFB
Enter / Exit Game Mode| Triple tap the left MFB

Q&A

Ql: What does the indicator on the charging case tell?

1. It shows the battery power left in the charging case by flashing slowly when you open up / close the lid or put either earbud back.
   Back Indicator Flash| Battery Leff
   ---|---
   Once| 0%-25%
   Twice| 25%-50%
   3 times| 50%-75%
   4 times| 75%-100%
2. While charging the charging case, the white indicator on the back flashes slowly and turns off after full charge.

Q2: How to charge the charging case?

1. Use a Type-C adapter to charge the case (current no more than 1 A).
2. Please charge the earbuds and charging case at least once per 3 months when not in use for a long time.

Q3: Why are the earbuds still connected to my phone after placing them back and closing the case lid?

1. The charging case has no remaining power. The case can’t turn off the earbuds if the case battery is dead.
2. Please make sure the earbuds are correctly placed in the charging case, and the contractors on both the charging case and earbuds are clean. Please try to clean them with something like a microfiber cloth.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, If not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user Is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna,
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device compiles part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifcatlons not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited.
Room 1308-1309, Building B, Huaihai Square, Chuangye Road, Longhua District Shenzhen, China. 518109
support@soundpeatsaudio.com
www.soundpeatsaudio.com

Company: Qing UG(haftungsbeschrankt)
Address: Undinestr. 7,12203 Berlin Germany

FCC ID: 2AONGDD004
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>