MONSTER 2MNSK0928 Blaster BoomBox Reimagined Portable Bluetooth Speaker User Manual
- June 6, 2024
- Monster
Table of Contents
BLASTER
Manual and Warranty
Model: 2MNSK0928
- Please fully charge before use.
- Please key in “0000” if the passcode is required when pairing.
- The speaker will automatically turn off after 15 minutes when there are no connections.
- For optimum performance with your iOS device, please ensure that your device is running iOS 4.1 or above.
Product Overview
- Mode button
- Power on / off / Bluetooth pairing
- Volume / Indoor / Outdoor level down button
- Volume / Indoor / Outdoor up button
- Power LED indicator
- Indoor mode LED indicator
- Volume mode LED indicator
- Outdoor mode LED indicator
- Volume / Indoor / Outdoor level LED indicators
- Bluetooth LED indicator
- NFC sensor
- Rubber cover
- 5mm audio line-in for music source
- 3.5mm audio line-in for microphone
- Charging port
- Charging out port
Charging the Speaker
- Please fully charge your speaker before use.
- To view battery level, turn on the speaker for battery level LED activation.
Pairing with Bluetooth-enabled Device – By NFC
Turn on the speaker by pressing and holding the “ ” button until a prompt tone
occurs.
Turn on the NFC feature on your device.
Tap your device on the NFC sensor.
You will hear the voice prompt “We are connected” once successfully paired.
You can start playing music.
Pairing with Bluetooth-enabled Device – By Setting
Turn on the speaker by pressing and holding the “ ” button until a prompt tone
occurs.
Press and hold the “ ” button until you hear the voice prompt. “Ready to
connect”.
You will hear the voice prompt “We are connected” once successfully paired.
You
Turn on the Bluetooth feature on your device.
Search and select “Monster Blaster” on your device. can start playing music.
Playing Music with a 3.5mm Audio Line-in Cable (Not Included)
Turn on the speaker by pressing and holding the “ button until a prompt tone
occurs.
Connect your device and the speaker with a 3.5mm audio line-in cable.
Start playing music from your device.
Using a Microphone
Turn on the speaker by pressing and holding the “ ” button until a prompt tone
occurs.
Start using the microphone while playing music.
Connect the speaker and the microphone with the microphone’s 3.5mm jack.
Volume / Indoor / Outdoor
Press the “ MODE ” button until the corresponding LED indicator
illuminates.
Press the “ + ” to increase the Volume.
Press the “ – ” to decrease the Volume.
Charging Your Device via USB
Press and hold the “ ” button until a prompt tone occurs to turn on the
speaker.
Connect your device and the speaker with a USB cable to start charging.
Precautions
-
Please read these safety instructions carefully.
- Do not use this product where contact with moisture, liquids, humidity, or rain is possible to avoid electric shock.
- Avoid exposing this product to direct sunlight, stovetops, or any other heat source.
- Do not cover the ventilation openings to prevent overheating.
- Do not drop, disassemble, deform, modify or insert any objects into this product.
- Do not attempt to repair, modify or disassemble the product yourself. This product does not contain any user-serviceable components.
- Do not clean the product with alcohol, ammonia-based cleaners, abrasive cleaners, or wet cloth. Only clean with a soft dry cloth.
- Do not place this product on its side, on slanted surfaces, or on the edge of high surfaces, like shelves, to prevent accidental falling.
- Do not bring your product into contact with any sharp objects.
- Do not attempt to replace the product battery, it is built-in and is not user-changeable.
- Observe all signs and displays that require an electrical device or RF radio product to be switched off in designated areas.
- Turn off your product prior to boarding an aircraft. Do not use the product inside an aircraft unless permitted by your airline.
- Dispose of the product and the product’s battery in accordance with local laws and regulations.
- Do not dispose of the battery with regular household waste.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates use and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
FCC Notice
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada (IC) Compliance Notice
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference. and (2) this device must accept any interference.
including interference that may cause undesired operation of the device. Under
Industry Canada regulations. this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users. the
antenna type and its gain should be so chosen that the equivalent
isotropically radiated pourer (e.i.r.p.) is not more than that necessary for
successful communication.
FCC ID: VVWE-2MNSK0928
To locate the FCC and IC identification numbers. please look at the underside
of theTeam Event.
Model number 2MNSK0928
LIMITED LIFETIME WARRANTY FOR CONSUMERS
What is covered under the Lifetime Warranty?
Monster® warrants that this product will be free from defects in workmanship
and materials under normal use (“Lifetime Warranty”). In a case where the
product is determined to be “defective”, we will repair the product free of
charge. If we cannot repair the product, we will replace it for you free of
charge.
How long am I covered?
You are covered for the lifetime of the product which means that as long as we
are still manufacturing and selling the product we cover you under warranty.
What is not covered under the Lifetime Warranty?
- Normal wear and tear of product use.
- Misuse, lack of care, mishandling, accidental damage, abuse, or other abnormal use.
- Use of the product other than for its intended purpose.
- Damage caused by improper or unauthorized repair or maintenance.
- The product that has been modified or altered.
- Any product that is not manufactured by Monster® (including, without limitation, any non-Monster® product that is used in connection with the product).
Customer Service Phone Number:
1-877-543-3540
Customer Service:877-543-3540
Model#: 2MNSK0928
The M Monster logo, and Powered by Monster are trademarks or registered
trademarks used under the license of Monster, Inc.
©2021 All rights reserved. Manufactured, marketed, and distributed by
Lifeworks Technology Group LLC. under license.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, This equipment
should be installed and operated with a minimum distance of 20cm the radiator
your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>