Shenzhen Feihe Electronics K7 LED Table Lamp User Manual

June 6, 2024
Shenzhen Feihe Electronics

Shenzhen Feihe Electronics K7 LED Table Lamp

Product Introduction

Please read carefully before using and keep it properly

operation instructions

Power connection

lnsert the matched adapter head into the socket behind the lamp.

Notrce:

  • Please use lite original power supply, do not use the cable extension or splitter, otherwise the product may work abnormal. ” Do not use an adapter which isn’t match with output 12V.
  • lfthe lights flickered or noisy please tlmely check the power supply
  • Do not connect the adapter metal point with other metals. or permanent damage to your product or other dangerous may resultor
  •  The original adapter for this product only,.and do not support for other use.
**Light operation

**

Reading light control
short press the button on the lamp head for dimming (dim-medium-bright turn off in turn)

light mode switch
long press the buutto to change the light color temperature cyclically.(Cool- werm-netural light in turn)

Night light control
short press the button on the base for night light dimming (dim-medium-bright- trun off in turn.it is dim when turn on)

Wireless charging function

Put the equipment with technical standard on the middle of qi logo to start charging

Notice: the light indicator is red when charging.and turn green when fully charged,if the red light is flashing.it means charging failure.

lllumination angle adjustment


warnning please do not over adjusting thier joint attivity parts to avoid any damage to the lamp.

Package list

Note: Product images and description only (or reference purpose, due to product upgrading, physical picture may be assodated with with some small differences In kind, please see the Subject produce.

Specification

Model K7
Working temperature 20-S0’C
Rated power 14W
Product net weight 6339
Color temperature range 30001+300k/4000K+400K/5500K+500K
product name LED table lamp
Output 12V/1.5A
wireless charger power 5W
Lamp size 19098560rnm

Cautions

  • Please wipe it by soft cotton fabric for su rlace cleaning, and do not use any corrosive solvents.
  • The light source is irreplaceable. Please stop use when actually wear out
  • If a failover occurs. please do not disassemble by yourself to avoid any damage on the product.You can contact the mRnufacture for maintenance.

Harmful matter content

Materia hazardous substance
( Pb ) ( Hg )
Metal
Plastic
Wire
**** PCBA board

The form is based on standard of SJ/T 11 364:
○: The hazardous substance is under the limit of thestandard ofGB/T 26572 in all homogeneous material of the component.
☓: The hazardous substance is in excess of the standard of GB/T 26572 in at least one homogeneous material of the component

Product Warranty regulation

The warranty services of this product is strictly in accordance with Consumer Protection Law and The product quality law of China.
If there is a performance fault listed in the “product performance fault table” after checking by after-sale service center,the service content is as follows:

  • Within 7 days after receiving the product,it is free to enjoy the refund and exchange service.
  • Within 8-15 days after receiving the product, it is free to enjoy replacement or maintenance service.
  • Within 12 months after receiving the product, it is free to enjoy maintenance service.

Non-warranty regulation

  • Unauthorized maintenance, misuse, collision, neglect, abuse, fluid intake, accident, altered or tear up labels/anti-fake label;
  • Exceed the warranty validity date;
  • Damage caused by force majeure;
  • Troubles are not on the range of “product performance fault table”
  • The human caused performance failure but listed in the product performance fault table”,including use of dimmer/non- rated voltage/non – specified environment.

Product performance fault table

Model Performance failure
K7
  1. The light doesn’t work

  2. Lamp flickering

  3. Unable to turn on the light

  4. Slow wireless charging

  5. Shell is damaged due to structural or material factors

  6. You’re advised to keep the packing boxes for at least 30 days after receiving, since the packing boxes are used to ensure the safety of transportation;

  7. This product is only sold in China mainland (excluding Hong Kong, Macao and Taiwan), so the warranty is for China mainland only(excluding Hong Kong, Macao and Taiwan.

FCC Statement

This device complies with part 18 of the FCC Rules. Operation is Subject To the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not explicitly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Note: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and candidate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.

This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Increase the separation between the equipment and any other radio device.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

ISED Statement

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:

  • This device may not cause interference; and
  • This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
During the operation of device a distance of 10 cm surrounding the device and 10 cm above the top surface of the device must be respected.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals