Shenzhen Feihe Electronics W20Q10C LED Table Lamp Instruction Manual
- June 5, 2024
- Shenzhen Feihe Electronics
Table of Contents
PLEASE READ BEFORE USING
If you find that you have any trouble or missing or damaged parts please
contact us.
If you need installation assistance, replacement parts, or have questions
regarding our warranty, please contact our product consultants at
customersupport@enchlites.com or call
toll-free:
1-800-936-3213
Monday to Friday from 9:00 a.m. to 5:00 p.m., EST. English and Spanish spoke.
International Regions: Please contact your local distributor.
WARRANTY
Sheffield Labs products are manufactured under the highest quality and
workmanship standards. Sheffield Labs guarantees the original buyer that this
product will be free of fabrication, material, and finish defects for one year
period starting at the purchase date. Sheffield Labs recommends professional
installation for this product.
Should this product present any leaks derived from a fabrication or material
defect during the warranty period, Sheffield Labs will supply the necessary
replacement parts free of charge. Sheffield Labs will also replace any pieces
presenting defects in finish or fabrication. This warranty is only valid under
normal installation, use, and service conditions.
This warranty does not apply to any damage caused by normal wearing of the
product, incorrect installation or operation, alterations or modifications
performed by parties not authorized by Sheffield Labs, or the use of
replacement parts of any brand other than Sheffield Labs. This warranty also
excludes damages caused by the use of abrasive cleaners, containing alcohol or
other organic solvents; whether the damage was caused by the consumer or third
parties. Sheffield Labs will not be responsible for workmanship expenses,
damages incurred during the installation, repair, or replacement, or for any
direct, indirect, consequential damage or losses related to this product. This
warranty is Sheffield Lab’s sole responsibility, leaving no further right or
actions to the original buyer or third parties and liberating Enchante Lites
New York and any other subsidiaries, affiliates, shareholders, distributors,
retailers, representatives, agents, and employees of these or any other
responsibility for visible or hidden defects or damages of any kind.
The purchase, use, and ownership of this product imply acceptance on behalf of
the original buyer of the terms and conditions of this warranty.
In order for the original buyer to make this warranty valid, any claim must be
accompanied by an original purchase ticket. To make this warranty valid write
Sheffield Labs to the email below with the subject: “Sheffield Labs Warranty”.
Explain the kind of defect and include the purchased ticket (original), your
full name and address, and phone number. Should the claim be compliant with
warranty limitations, all necessary replacement parts will be mailed at no
cost to the customer.
customersupport@enchlites.com
1-800-936-3213
Monday to Friday from 9:00 am to 5:00 p
LED table lamp
Thank you for purchasing a Sheffield Labs product. All Sheffield Labs products
are carefully engineered and factory tested for durability under normal
conditions. We develop our products for simple installation. Follow our
instructions to help you easily install your Sheffield Labs LED desk lamp
USER MANUAL
SAVE THESE INSTRUCTIONS AND READ CAREFULLY BEFORE USE
For Customer Care, production operation information, or problem resolution,
call toll-free at 1.800-936-3213
IMPORTANT SAFETY INSTRUCTIONS
WARNING: TO PREVENT ELECTRIC SHOCK, MAKE SURE THE LAMP IS NOT PLUGGED IN
UNTIL ALL STEPS ARE COMPLETE.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
TURN THE LAMP OFF AND WAIT UNTIL THE LAMP AND ADAPTER ARE COOL BEFORE
HANDLING.
- The LED lamp head (A) might get hot after several hours of continuous use. DO NOT place your hands directly on the LED light panel.
- Never use an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
- Do not alter the plug.
- The lamp head included with this unit cannot be replaced by the consumer.
- Do not place flammable material near or over the lamp.
- Ensure the lamp is not installed next to any air vents and is not in any moist or damp areas.
- INDOOR USE ONLY
NOTE: The important safety instructions appearing in this manual are not
meant to cover all possible conditions and situations that may occur. It must
be understood that common sense, caution, and care must be used with any
electrical product.
CAUTION: Any change or modification to this product not expressly
recognized by Enchante Living voids Enchante’s responsibility for the proper
function of the product.
A | Led Lamp Head |
---|---|
B | Lamp Arm |
C | Wireless Charging Pad |
D | USK Charging Port |
E | USB-C Charging Indicator |
F | USB-A Charging Port |
G | Wireless Charging Indicator |
H | Power Adaptor Input |
I | Cooling Vent |
J | Power Adaptor |
K | Touch Switch |
INSTRUCTIONS
NOTE: THIS UNIT IS FULLY ASSEMBLED
-
Remove lamp from packing, placing lamp base flat on a steady surface.
-
Connect the power connector to the power adapter input (H) at the rear bottom of the lamp.
-
Plug the power adaptor (J) into a standard household 120V AC outlet.
• NOTE: Only use the supplied power adapter to avoid damage or risk of fire. -
The power switch (K) is a touch-activated switch that controls ON/OFF the power.
-
Tap the touch sensor (K) to power on the lamp. Default brightness will be set to low. Tap again to adjust the brightness to your desired level (low-med-high-off).
-
To reposition the light, hold the base steady and grasp the lamp arm (B) depending on the necessary adjustment.
• NOTE: DO NOT FORCE the shade outside the allowable adjustable range as excessive adjustment may cause damage. -
Center your device on the Qi wireless charging pad (C) and a red indicator light (G) on top of the base will indicate charging. If the red indicator light begins to flash, your device may not be centered on the charger. Once the indicator light turns green, charging is complete.
-
THIS LAMP CONTAINS max. 18W USB-A output port (F), and a rapid-charging mac. 30W USB-C port (D) is located towards the base. USB ports can charge items such as tablets, cellular phones, etc. Simply insert the appropriate charging cable into either port when plugged in, and charging should commence. The USB-C port (D) has an LED indicator (E) that illuminates when charging is active. The USB-A port does not, and the transfer of power should begin as soon as your compatible device is plugged in.
The “Or symbol is a trademark of the Wireless Power Consortium. All mobile devices with integrated wireless charging support tiTM.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
Qi- Certifred
Wireless Charging
Technology
an ENCHANTE brand
2021-2022 ENCHANTE ACCESSORIES, INC
AMG, JV, LIC I ENCHANTE INES LLC
NEW YORK, NY 10001
PRODUCT SPECIFICATIONS
Lumens: | 250-350LM |
---|---|
Total Wattage: | 60 W |
Power Adaptor: | 24 VI 2.5 A |
Wireless Charger Output: | 10 W |
Color Temperature: | 4200±400K |
USB-A Output: | Max. 18W |
USB-C Output: | Max. 30W |
PRODUCT MAINTENANCE
- Always ensure the power is OFF and the lamp has cooled down before performing any maintenance, cleaning, or adjustments.
- To avoid injury or damage to the lamp, ensure that the adapter and any screws are secure before reconnecting to power.
- To clean, wipe with a damp or dry clean cloth. Never soak the lamp with water.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>