emos P56201 Digital Room Thermostat User Manual

emos P56201 Digital Room Thermostat

Product Information

The P56201 thermostat is designed for controlling heating and air-conditioning systems. It can be controlled using a mobile application for iOS or Android. The thermostat is compatible with various countries and languages.

Important Notes

• Before the first use, carefully read the instruction manual for the thermostat and the manual for the boiler or air-conditioning equipment.
• Turn off the power supply before installing the thermostat.
• Follow applicable standards during installation.

Product Usage Instructions

Installing the Thermostat

1. Remove the rear cover of the thermostat.
2. Mark the spots for holes.
3. Drill two holes and insert plastic wall plugs into them.
4. Fasten the rear thermostat cover using two screws.
5. Connect the wires to the labeled terminals according to the wiring diagram found under the cover.
6. Fit the thermostat onto the mounted rear.

Putting the Device into Operation

1. Set the Clock and Calendar:
   • Press the button; the values ​​will start flashing.
   • Use the buttons to set the desired values.
   • Confirm the set value by pressing the button.
   • To end the setting, press the button or wait for 30 seconds.
2. Holiday mode:
   • Long-press (5 seconds) the button; the time value will start flashing.
   • Release the button and press it again for 5 seconds.
   • The icon will appear and the number of days will start flashing.
   • Repeatedly press the button to set the number of days (from 1 to 99).
   • Confirm the set number of days by pressing the button; the temperature value will begin flashing.
   • Repeatedly press the button to set the temperature.
   • Confirm by pressing the button; the icon will appear.

Note: For detailed instructions and additional features, refer to the instruction manual provided.

The P56201 thermostat is designed for controlling heating and air-conditioning systems.

Important

• Before the first use, make sure to carefully read the instruction manual for the thermostat, as well as the manual for the boiler or air-conditioning equipment.
• Turn off power supply before installing the thermostat!
• Installation should be carried out by a qualified person!
• Follow applicable standards during installation.

Technical specifications

• Switched load: max. 230 V AC; 6 A for resistive load; 2 A for inductive load
• Temperature measurement: 0 °C to 40 °C with 0.1 °C resolution; accuracy ±1 °C at 20 °C
• Temperature setting: 5 °C to 35 °C in 0.5 °C increments
• Temperature differential setting: 0.2 °C to 2 °C in 0.1 °C increments
• Operating temperature: 0 °C to 40 °C
• Power supply: 230 V AC/50 Hz
• Dimensions: 138 × 88 × 33 mm

Description of the Thermostat – Icons and Buttons

1. day number
2. time
3. WiFi signal reception
4. cooling /heating mode
5. set temperature
6. menu lock
7. holiday mode
8. temporary change of temperature
9. HOLD mode
10. current room temperature
11. programme settings
12. data and time settings
13. function selection, confirmation
14. temporary change of temperature; navigation in the settings
15. return to main menu

Installing the Thermostat

Description of the Back of the Thermostat

1. contact connection cover
2. mounting holes
3. mounting direction

Mobile Application

• The thermostat can be controlled using a mobile application for iOS or Android. Download the EMOS GoSmart app for your device.

QR code for downloading the Android app

QR code for downloading the iOS app

Description of Registering and Logging into the Application

• To use the mobile application, you must first register by tapping the Sign Up button.
• Enter your country and e-mail address, check off your consent with the end user licence agreement and tap Get Verification Code.
• Enter the verification code sent to your e-mail.
• Then, set the password for your account and tap Done.
• Choose whether you want to enable Data Analysis/Personalisation and tap Go to App.

Connecting the Thermostat to a Wi-Fi network for Control via the Mobile App

• Tap Add Device in the app and enable location access.
• Choose add manually and select Small Home Appliances – Thermostat (Wi-Fi) or Others – Others (Wi-Fi).
• Select a 2.4 GHz Wi-Fi network, enter the password and tap Next.
• Check off Confirm that the indicator is flashing rapidly and tap Next.
• The chosen thermostat should appear in the app within 2 minutes.
• Tap the green arrow on the right; the thermostat will be added into the app.
• Then tap the thermostat icon in the app to open the main control menu.

Note

• If the thermostat fails to pair, repeat the process.
• 5 GHz Wi-Fi networks are not supported.
• The thermostat can only be controlled via the app by 1 user at a time. If another user wants to control the thermostat, the previous user must log out.

Description of the Main Menu of the Mobile App

Tap the thermostat icon in the app to open the main control menu

• 1. Thermostat status (ON/OFF) – Anti-freeze mode, temperature fixed to 5 °C
• 2. Work mode setting (detailed information in the WORK MODES chapter of this manual)
  • Automatic A
  • Manual – see HOLD mode
  • Temporary – see Temporary change mode
  • Boost – see Timed temporary change mode
  • Holiday – see Holiday mode
• 3. Schedule

1. add a time period
2. delete a time period
3. day display
  * 7 days (Mon → Sun)
  * 5+2 days (Mon → Fri + Sat → Sun)
  * 24-hour

• Every day can be divided into a maximum of 6 periods.
• When in 7 day mode, you can copy the temperature settings from one day into other days (see fig. 8).

Example

• Long-press the Thursday icon; a menu of other days will open. Mark them orange by tapping them and confirm.
• Thursday‘s schedule will copy over to Monday, Tuesday and Wednesday.

4. Setting

1. reset the thermostat to factory settings
2. key lock
3. correction of ambient temperature (-3 °C to +3 °C in 0.5 °C increments)
4. heating/cooling system mode
5. calendar mode (7 days, 5+2, 24 h)

5. Thermostat mode icon

• heating
• cooling
• off

1. 6. Work mode icon
2. 7. Adjust temperature
3. 8. Current room temperature
4. 9. Current set temperature
5. 10. Adjust temperature
6. 11. Network information about the device, change the name in the app, location information, add an icon to the home screen, and other similar settings

Deleting the Thermostat from the App

• Long-press the thermostat icon, check off the thermostat and tap the dustbin icon to delete the thermostat.

User Overview/Password Change/App Update

• Tap the icon in the bottom right and then the icon in the top right.
• This will open a new menu with settings.

INSTALLATION

Attention

Before changing the thermostat, disconnect the heating system from the mains power in your home. This will prevent potential injury by electric current.

Installing the Thermostat

1. Remove the rear cover of the thermostat.
2. Mark the spots for holes.
3. Drill two holes, carefully insert the plastic wall plugs into them and use two screws to fasten the rear thermostat cover.
4. Connect the wires to the labelled terminals according to the wiring diagram found under the cover.
5. Complete the installation by fitting the thermostat onto the mounted rear cover.

Placement of the Thermostat

The placement of the thermostat (transmitter unit) significantly affects its functioning. Choose a location where members of the family spend most of their time, preferably near an inside wall where air circulates freely, with no direct sunlight. Do not place the thermostat in the vicinity of heat sources (such as TV sets, radiators, fridges), or close to a door. Failure to comply with these recommendations will prevent proper control over room temperature.

Wiring Diagram

Pump/Motorised Valve Connection Diagram

Floor Heating Connection Diagram

Boiler Connection Diagram

• The pre-installed wire coupler will not be connected.

Expansion Valve/Electric Drive Connection Diagram

PUTTING THE DEVICE INTO OPERATION

Setting the Clock, Calendar

• Press the button; the values will start flashing.

Use the buttons to set the following values (holding the button down accelerates the value change):

• Day – Month – Year – Hour – Minute.
• Confirm the set value by pressing .
• To end setting, press the button or wait 30 seconds.
• After setting is complete, the current day number will be displayed:

1. Monday
2. Tuesday
3. Wednesday
4. Thursday
5. Friday
6. Saturday
7. Sunday

WORK MODES

Holiday Mode

• Sets a constant temperature for an extended period of time.
• Long-press (5 seconds) the button; the time value will start flashing.
• Release the button and press it again for 5 seconds.
• The icon will appear and the number of days will start flashing.
• Repeatedly press the button to set the number of days (from 1 to 99).
• Confirm the set number of days by pressing ; the temperature value will begin flashing.
• Repeatedly press the button to set the temperature.
• Confirm by pressing ; the icon will appear.
• If you want to go back and change the temperature for holiday mode, press the button repeatedly.
• You can cancel holiday mode by pressing or .

Temporary Change Mode

• Short-term manual change of temperature.
• While in Auto mode, use the buttons to change the temperature setting; the value will be saved automatically.
• The icon will appear.
• This mode will be automatically cancelled by the first programmed temperature change (the time remaining until the change + clock will be alternating in the top left corner) or it can be cancelled manually by pressing .

OFF Mode

• Anti-freeze mode, temperature fixed to 5 °C.
• While in Auto mode, press the button 2×; a temperature of 5 °C will appear in the top right corner.
• To cancel the mode, press .

Timed Temporary Change Mode

• Temporary manual change in temperature for 1 to 9 hours.
• While in Auto mode, long-press the button; the time setting will start flashing in the top left corner.
• Use the buttons to set the duration of the temperature change, from 1 to 9 hours, with 1 h resolution.
• Confirm by pressing . Then set the temperature of choice using the buttons.
• The remaining set time + the clock will be alternating in the top left corner; you can cancel the mode prematurely by pressing .

HOLD Mode

• Permanent manual temperature change.
• While in Auto mode, press the button; the HOLD will appear in the bottom right.
• Set the temperature of choice using the buttons; the value will be saved automatically.
• The set temperature will be maintained until HOLD mode is cancelled.
• Any programmed temperature change will not be carried out.
• To cancel HOLD mode, press .

Heating Programme Setting Mode

• Sets temperature over the course of the whole day (6 temperature changes in the day).
• Press the PRG button. The day number will start flashing (1–7 = Monday to Sunday).
• Press repeatedly to select the days of the choice.
• Different each day programme – the number of the selected day flashes
• Monday to Friday programme – 12345 flashes
• Saturday to Sunday programme – 67 flashes
• All week programme – 1234567 flashes
• Select your programme of choice and confirm with .
• The time of the first temperature change will be flashing; you can set the time by repeatedly pressing (10 minute increments), then confirm with .
• The temperature value will begin flashing; set by repeatedly pressing .
• P1 will appear below the set temperature, indicating the 1st temperature change in the day.
• Confirm by pressing . Continue by setting the start of the second temperature change (P2 will appear under the temperature).
• Set the time and temperature by following the same steps as when setting the 1st temperature change.
• Continue the process until all 6 temperature changes (P1 to P6) are set.
• Factory pre-set times and temperatures are as follows:

Monday to Friday

Saturday to Sunday

Screen Illumination

• Pressing any button will illuminate the screen for 15 seconds.

Other Technical Settings

• Long-press the button for about 5 seconds.
• Repeatedly pressing the button selects from the functions below, values are adjusted using the buttons.

Connecting the Thermostat to WiFi (COFI)

• Long-press the button for about 5 seconds.
• Then press and hold the button for 3 seconds.
• E2 will appear on the screen and the icon will be flashing.
• Complete the pairing of the thermostat in the mobile app.
• See instructions for Connecting the Thermostat to a WiFi Network for Control via the Mobile App.

Switching Heating/Cooling Mode

• Long-press the button for about 5 seconds.
• Press the button once.
• Use the buttons to switch to heating (HEAT) or cooling (COOL) mode.
• Confirm with .

Setting the Temperature Differential

• The temperature differential (hysteresis) is the difference in temperature required for switching the system on and off. If, for example, you set the temperature in the heating system to 20 °C and the differential to 0.2 °C, the thermostat activates heating as soon as room temperature drops to 19.8 °C and switches heating off when temperature reaches 20.2 °C.
• Long-press the button for about 5 seconds.
• Press the button 2× and use the buttons to set the temperature differential value (0.2 °C to 2 °C in 0.1 °C increments). Confirm with .

Ambient Temperature Calibration (CAL)

• The temperature sensor in the thermostat is calibrated from production, but additional calibration can be done to optimise the thermostat further, for instance by comparing the measured room temperature with a reference thermometer.
• Long-press the button for about 5 seconds.
• Press the button 3× and use the buttons to set the calibration value (-3 °C to +3 °C in 0.5 °C increments).
• Confirm with .

Time Synchronisation (SYNC)

• Long-press the button for about 5 seconds.
• Press the button 4× and use the buttons to set:
• ON – time will be automatically synchronised with the Wi-Fi network;
• OFF – time will not be synchronised with the Wi-Fi network and the time you set manually will be used.
• Confirm with .

Software Version

• Long-press the button for about 5 seconds.
• Press the button 5×; the software version of the thermostat will be displayed.
• Return by pressing .

Resetting the Thermostat (rESE)

• Long-press the button for about 5 seconds.
• Press the button 6×; rESE will appear on the screen.
• Press the PRG button; — — will be displayed.
• Press the PRG button again; the thermostat‘s menu will be reset and all set values will be deleted.

Key Lock

• Long-press the PRG button for about 3 seconds.
• All buttons will be locked, the thermostat will flash LOC in the top left of the screen and the icon will be displayed.
• To cancel the lock, hold the PRG button again for about 3 seconds; UNLO will flash on the screen.

Setting the lock in the mobile app:

• lock activation,
• lock deactivation

Attention: If you activate the lock in the app, the lock can also be cancelled using the PRG button on the thermostat.

Maintenance

Upkeep and Maintenance

The product is designed to serve reliably for many years if used properly. Here are some tips for proper operation:

• Read the manual carefully before using the product.
• Do not expose the product to direct sunlight, extreme cold and humidity and sudden changes in temperature. This would reduce measuring accuracy.
• Do not place the product in locations prone to vibration and shocks – may cause damage.
• Do not subject the product to excessive force, impacts, dust, high temperatures or humidity – doing so may cause malfunction, shorten battery life, damage batteries and deform plastic parts.
• Do not expose the product to rain or high humidity, dropping or splashing water.
• Do not place any open flame sources on the product, e.g. a lit candle, etc.
• Do not put the product in places with inadequate air flow.
• Do not insert any objects into the product‘s vents.
• Do not tamper with the internal electrical circuits of the product – doing so may damage the product and will automatically void the warranty. The product should only be repaired by a qualified professional.
• To clean the product, use a slightly moistened soft cloth. Do not use solvents or cleaning agents – they could erode the plastic parts and cause corrosion of the electric circuits.
• Do not immerse the product in water or other liquids.
• In the event of damage or defect of the product, do not perform any repairs by yourself. Have it repaired in the shop where you bought it.
• This device is not intended for use by persons (including children) whose physical, sensory or mental disability or whose lack of experience or knowledge prevents them from using it safely. Such persons should be instructed in how to use the device and should be supervised by a person responsible for their safety. Children must always be supervised to ensure they do not play with the device.

ATTENTION: The contents of this manual may be changed without prior notice – due to printing limitations, the symbols shown may differ slightly from those on the screen – the content of this manual may not be reproduced without the manufacturer‘s permission.

WARRANTY STATEMENT

1. We declare that we guarantee the properties and flawless operation during the warranty period deadline.
2. The warranty period begins on the date of delivery of the goods and is valid for 24 months.
3. EMOS SI, d.o.o. guarantees the buyer that it will be at his own expense within the warranty period eliminated all defects on the device due to a factory defect in the material or manufacturing.
4. The warranty period is extended for the duration of the repair.
5. If the device is not repaired within 45 days from the date of notification of defects, the damage may be affected the customer requests a new one or a refund of the amount paid.
6. The warranty ends if the defect is caused by:
   • non-professional-unauthorized service
   • modifications without the approval of the manufacturer
   • failure to follow the instructions for use of the device
7. The warranty does not exclude the consumer’s rights arising from the seller’s responsibility for product defects.
8. Unless otherwise indicated, the guarantee is valid in the territory of the Republic of Slovenia.
9. The manufacturer provides, against payment, repair, maintenance of the goods, replacements parts and attachments for three years after the expiry of the warranty period.
10. Natural wear and tear of the device is excluded from the warranty obligation. The same also applies for damage due to improper use or overloading.

INSTRUCTIONS FOR THE COMPLAINT PROCEDURE

The owner asserts a warranty claim by reporting the identified defect to an authorized person workshop (EMOS SI, d.o.o., Rimska cesta 92, 3311 Šempeter in Savinjska dolini) in writing or orally. The buyer is responsible if he causes damage by late registration on the device. After the warranty period expires, the right to claim the warranty expires claim. A certified warranty card with the original invoice must be attached. EMOS SI, d.o.o. undertakes to replace the device with a new one if it is covered by this warranty roku would not work flawlessly.

More Information

• Service: EMOS SI, d.o.o., Rimska cesta 92, 3311 Šempeter in Savinjska dolina, Slovenia
• phone: +386 8 205 17 21
• e-mail: reklamacije@emos-si.si

Other countries

• The full manual is available at the following internet address: https://en.b2b.emos.cz/download.
• You can also contact us at support@emos.eu.

Scan

Documents / Resources

| emos P56201 Digital Room Thermostat [pdf] User Manual
P56201 Digital Room Thermostat, P56201, Digital Room Thermostat, Room Thermostat, Thermostat
---|---
| emos P56201 Digital Room Thermostat [pdf] Instruction Manual
P56201 Digital Room Thermostat, P56201, Digital Room Thermostat, Room Thermostat, Thermostat

References

• EMOS | Elektro eshop a velkoobchodEMOS | Elektro eshop a velkoobchod
• Download Center EN | EMOS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>