enbrighten 63185/66350 5-Head Chandelier with LED Vintage Bulbs User Guide
- June 6, 2024
- enbrighten
Table of Contents
enbrighten 63185/66350 5-Head Chandelier with LED Vintage Bulbs User
Guide
Congratulations on your new Décor Chandelier by Enbrighten! Blending old-world
décor with a clean and modern style, this lamp will enhance your space with
premium illumination. Before installing, read through these instructions and
take note of any safety warnings.
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag type fixture be installed on a
ceiling, which contains a radiant type heating system. If you are unclear how
to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
INSTALLATION
Carefully remove the fixture from the packaging and check that all parts are included as shown in the figure. Be careful not to misplace any of the included screws or parts that are needed to install this fixture.
-
Turn power OFF
Ensure power is turned OFF at the circuit breaker or fuse box. -
Install mounting bracket
Secure the mounting bracket (C) onto your ceilings’s junction box with the included mounting screws (F). -
Combine rods
Determine the fixture’s height by combining any of the provided 6in. (I) and 12in. (J) rods. -
Thread wires
Gently feed the wires through the rods and canopy (G), then fasten the rods to the canopy and the fixture’s base (K).
NOTE: If needed, use wire cutters to trim length of wires. -
Neutral and live wires
Using the wire nuts (B), connect the ribbed wire to the white (neutral) supply wire from the junction box. Then connect the smooth wire to the black (live) supply wire from the junction box. -
Ground wire
Connect the ground wire from the junction box and ground wire from the fixture with a wire nut or the ground screw (E) on the mounting bracket (C). Tighten the ground screw to secure both wires. -
Secure wiring
Wrap electrical tape (not included) around the wire nuts (B) to ensure they are secured. Then, gently arrange all wiring inside the junction box, making sure there are no exposed connections. -
Attach canopy
Align the canopy (G) with the pre-installed screws (D) on mounting bracket (C) and fasten it into place using the two cylinder nuts (H). -
Insert bulbs
Thread the included T bulb into the sockets. NOTE: Use medium base 60W MAX incandescent bulbs or 60W equivalent SBCFL or SBLED bulbs as an alternative. -
Install glass shades
Place each glass shade (N) onto the corresponding cups (L) and secure them into place with the cup screws (M). -
Restore power
With the fixture properly installed, restore power at the circuit breaker or fuse box and turn the light on using the associated in-wall switch.
- A. Junction box (not included)
- B. Wire nuts (x3)
- C. Mounting bracket
- D. Pre-installed screw/nut (x2)
- E. Grounding screw
- F. Mounting screw (x2)
- G. Canopy
- H. Cylinder nut (x2)
- I. 6in. rod (x2)
- J. 12in. rod (x2)
- K. Fixture base
- L. Cup (x5)
- M. Cup screws (x15)
- N. Glass shade (x5)
FOR YOUR SAFETY
WARNING: BE SURE THAT ELECTRICAL POWER TO THE WIRES YOU ARE WORKING ON IS SHUT
OFF AT THE CIRCUIT BREAKER OR FUSE BOX.
CLEANING
To clean this fixture, wipe it with a soft and dry cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
WARNING
RISK OF ELECTRIC SHOCK
- DO NOT USE IN WET LOCATIONS
- USE INDOORS ONLY
- TURN POWER OFF BEFORE SERVICING – SEE INSTRUCTIONS
- PROPERLY GROUND FIXTURE
- ENSURE THAT NO BARE WIRES ARE EXPOSED OUTSIDE THE ELECTRICAL CONNECTIONS
RISK OF INJURY
- SOME METAL PARTS IN THE FIXTURE MAY HAVE SHARP EDGES. TO PREVENT CUTS AND SCRAPES, WEAR GLOVES WHEN HANDLING THE PARTS.
- DO NOT OPERATE THE UNIT WITH A MISSING OR DAMAGED LENS
- ACCOUNT FOR SMALL PARTS AND DESTROY PACKAGING MATERIAL AS THESE MAY BE HAZARDOUS TO CHILDREN
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>