MERKURY MI-SO75B-101 Wireless Home Theater Soundbar and Speaker User Manual
- June 6, 2024
- Merkury
Table of Contents
MERKURY MI-SO75B-101 Wireless Home Theater Soundbar and Speaker User Manual
Connecting to the Soundbar
Use the Mode Select button to cycle through each input mode. The indicator light will show which mode you have currently selected:
- Blue: Bluetooth Mode
- White: Optical Mode
- Blinking White: HDMI Mode
- Pink: USB Mode
- Green: Line Mode
Aux Input
Simply connect a device to the PUR Sound soundbar via the aux input and
play your music instantly, adjusting the volume on both the device and the
speaker.
USB Connect
You can connect any USB memory device to the speaker. The PUR Sound
Soundbar recognizes and plays MP3 format audio files. Play, pause, skip, and
repeat tracks with the on-board controls.
Bluetooth
With the soundbar in Bluetooth mode, go to your device’s Bluetooth settings
and search for new devices. In a moment, “Merkury S075B” should appear. Tap it
and a sound should emit from the soundbar to indicate the device is connected!
NOTE: Soundbar will always auto-pair with your device as long as it is in range and your device’s Bluetooth is enabled.
Specifications
Specifications:
- Output Power : 10W
- Frequency Response: 20Hz to 20KHz
- Dimensions (WxHxD): 810mm x 75mm x 75mm
Additional Connection Sources:
- Audio: 3.5mm AUX cable
- Power Source: Built-in rechargeable battery or via USB cable
Power Information:
- Input: DC 5V
- Battery Capacity: 1500mAH
- Music playing time: Up to 8 Hours*
- Charging time: 4 Hours*
Bluetooth® Information
- Bluetooth® Specification: V5.0
- Operating Distance: Up to 10m
- System Requirements: Bluetooth® enabled device
*Depends on individual use and may be slightly more or less than the time specified.
Powering The Soundbar
- Be sure the PUP Sound soundbar is fully charged using the included Micro USB cable. Connect one end to the speaker and the other end to a USB A/C Power Wall Adapter.
- The power button is located on the side of the soundbar.
- The speaker will emit a low chime when the battery is running low.
Soundbar Inputs and Buttons
- Power ON/Mode Select
- Play/Pause & Mute (Line/Optical/HDMI only)
- Volume Up/Skip Track
- Volume Down/Previous Track
- USB Input
- Line Input
- Optical Input
- HDMI Input
- DC5V Charging Input
Back of Soundbar
Troubleshooting
No power: Recharge the soundbar using the included micro USB cable. Try using a different cable.
Music Is not playing over Bluetooth: Make sure your Bluetooth device has A2DP profile. Check If both devices are paired and connected over Bluetoothe. Restart the speaker to reconnect your Bluetooth® device.
Bluetooth device will not reconnect with the speaker: Navigate to your Bluetooth° settings menu on your Bluetoothe device, tap “Merkury S075B” and select “Forget.” Now follow the steps to pair your device again.
FCC Warning
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance from the antenna should be included in the User manual. So, this device is classified as Mobile device.
FCC Notice:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the two following conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Technical Support
Please do not attempt to fix the product by yourself. If you are experiencing any problems with me product, please do not return it to the store you bought it from. You can contact our technical support representatives and they will assist you with any questions you might have.
For assistance operating your product, please consult the User Manual first, then feel free to contact Merkury Innovations technical support:
Medan Innovations 45 Broadway, 3rd Floor New York, New York 10006
Web: www.merkuryinnovations.com
E-mail:
support@merkuryinnovations.com
@ 2021 Merkury Innovations, LLC. 45 Broadway 3rd FL. New York, NY 10006 To explore our full selection of products, visit us at: www.merkuryinnovations.com
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc. The illustrated product and specifications may differ slightly from
those supplied. All other trademarks and trade names are those of their
respective owners.
Made in China
FILE INFORMATION
DATE: 07/19/21
FACTORY: ETI GROUP LIMITED
MODEL NUMBER: MI-S075B-101 (MANUAL)
PRINTER SPECIFICATIONS
FILE NAME: MI-S0758-101_Manual_071921_0Lai
SCALE: 100%
SIZE: Trim: W 221 mm x H 151 mm
PAPER STOCK: 80g Art Paper
FINISH: Matt Lamination
INKS: 1/1 Grayscale
PRESS WORK / NOTES: Trim to size, score, fold, & glue in specified
areas.
Trim
Score
DO NOT print Comments or Dielines. Physical sample according to specs must be approved by MERKURY before proceeding to production.
CONTACT
MERKURY CHINA: Perry
perry@merkuryinnovations.com.cn
COMMENTS (Internal reference only)
File created by Eileen
- Please include this manual in all packaging for MI-S075B-101
- Grayscale
- Double sided printing