COLBOR CL100 Video Light User Manual

June 6, 2024
COLBOR

CL100 Video Light User Manual

Thank you for choosing COLBOR product. Please read this manual carefully before use and follow all instructions mentioned herein.

Caring For Your Colbor Product

  • Keep corrosive chemicals, liquids, and heat sources away from the product to prevent mechanical damage
  • The product is not waterproof.
  • Do not leave the product unattended while in use. Keep out of reach of children
  • Must remove the protective cover before use.
  • Do not handle with wet hands. Do not touch the hot COB surface.
  • Please do not block the ventilation and do not look at the light directly when it is on.
  • Do not attempt to disassemble or modify the product. Doing so voids the warranty.
  • Please have the product checked or repaired by authorized technicians if any malfunctions happened.
  • Disconnect from the power supply when it is not in use.
  • Malfunction may be caused by dropping, the impact of external force.
  • Failure to follow all the instructions may result in mechanical damage.
  • Warranty does not apply to human errors.

Product Instructions

If there is no operation for 10 seconds, the current settings are automatically saved and the selection mode is exited.
1) Power Button
Short press to turn on/ off the light
2) Mode Switch
Default Mode: CCT Each press switches to the next lighting mode (OCT —> EFF- CANDLE EFF-BONFIRE —> EFF-BLN —> EFF-FAULTY BULB —, EFF-FLASH —’ EFF- LIGHTNING) Long press for 3 seconds to enter Overclock mode. * In overclock mode, the output power will be enhanced for the 60s. At this time, the fan runs at full speed with the fan status of “FULL”. When the mode ends, the previous fan status restores.
3) Adjustment Dial

  1. Short press the dial to switch between Brightness and Color Temperature Control
  2. Roll the dial to adjust the value Brightness (0-100); Color Temperature (2700-6500K)
  3. Press the dial again to switch to another control

4 )Group Option
Press the button to set group (Group A/B/C/D/E)
5) Fan Option
Default Status: SMART SMART-The fixture will adjust the fan speed according to working temperature. Press the Fan Option and switch to QUIET status. QUIET- The fan is off. In order to protect the light, the power will be reduced to avoid overheating damage.
6) Fan Status
SMART / QUIET / FULL
7) Power Status
Percentage icon means battery power is being used Plug icon means AC power is being used
8) Brightness
9) Color Temperature
10) Group

Operation Instructions

  1. Connect the fixture with the power adapter, then plug it into an electricity supply.
  2. Press the Power Button to turn on the light.

CCT Mode

Brightness Control (0-100)
Color Temperature Control (2700-6500K)
EFF Mode
EFF
CANDLE
Specific color temperature range: 2700–3000K Specific brightness range: 30-100 Rate: 5 levels of flicker frequency (05 > 04 > 03 > 02 > 01)
BONFIRE
Specific color temperature range: 2700-4000K Specific brightness range: 30-100 Rate: 5 levels of flicker frequency (05 > 04 > 03 > 02 > 01)

EFF| BLN (Pulsing)| natIMColor temperature range: 2700–6500K Specific brightness range: 30-100

Rate: 5 levels of flicker frequency (05 > 04 > 03 > 02 > 01)

---|---|---
FAULTY BULB| Specific color temperature range: 2700-6500K Specific brightness range: 30100

Rate: 5 levels of flicker frequency (05 > 04 a. 03 > 02 > 01)

FLASH| Specific color temperature range: 5600-6500K Specific brightness range: 30-100

Rate: 5 levels of flicker frequency (05 > 04 > 03 > 02 > 01)

LIGHTNING| Specific color temperature: 6500k

Specific brightness range: 30-100

Rate: 5 levels of flicker frequency (05 > 04 > 03 > 02 > 01)

Brightness Control / Color Temperature / Rate Control
Short press the Adjustment Dial to switch among color temperature °onto! ( °Mr flashes), rate control (°FATE’ flashes) and brightness control, then roll the dial to adjust.

Remote Control Instructions

  1. Switch
  2. Overclock Mode
  3. Brightness +
  4. Brightness-
  5. Color Temperature –
  6. Color Temperature +
  7. Fade In/ Fade Out
  8. CCT Mode
  9. EFF Mode/ Remote Pairing
  10. Rate (Flicker Frequency)
  11. Preset Color Temperature: 3200K
  12. Preset Color Temperature: 6500K

Pair the CL100 with the remote control

  1. Disconnect the CL100 from the power supply and reconnect with the
  2. Point the remote control to the CL100 control panel and long-press the EFF Mode button on the remote control in 3 seconds after the power supply is
  3. If they are paired, the CL100 will flash three times and display the program version number.
  4. The remote control can be used as required once

Unpair the CL100 with the remote control

  1. Disconnect the CL100 from the power supply and reconnect with the
  2. Point the remote control to the CL100 control panel and long-press the Overclock Mode button on the remote control in 3 seconds after the power supply is connected.
  3. tf the pairing is canceled successfully, the CL100 will flash three times.
  • In the case of mufti-light control, all lights must be switched off before the remote control is applied. Otherwise, the control will be out of sync.

Specifications

Color Rendering Index: ≥97
Color Temperature Range: 2700-6500K
Beam Angle:≈< 120° (With  Standard Cover 55°)
Power: 100W (Constant Power)
Light Working Voltage:
DC 15V 8A
Connector. GX16 3-Pin Connector
Body Material: ABS
Light Dimension(mm): 202116117 (Light Base Not Included)
Light Weight: 1.1 kg/39oz
Power Adapter Input: AC 100V-240V 50-60Hz 2.0A
Power Adapter Output DC 15V 9.6A

Package List

WARRANTY

Warranty Period

Thank you for purchasing COLBOR products.

  1. Customers are entitled to free replacement or repair service in case of the quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
  2. Original COLBOR products are entitled to a 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user.
    Within the warranty period, if a product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).

Warranty Exclusions and Limitations

  1. Faults resulted from inappropriate use of a product without following its operation specification
  2. Artificial damage, e.g. crash, squeeze, scratch, soaking, exposing to rain or damp
  3. Modifications to a product by its user or a third party without the prior written consent of COLOR,g. replacement of element or circuit, label alteration
  4. The code on the product is inconsistent with that of the warranty certificate, or the code on the product or warranty certificate is altered or torn off
  5. All consumable accessories attached to a product, like a cable, cover
  6. Faults as a result of force majeure, such as fire, flood, lightning, etc.

Warranty Claim Procedure

  1. If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact COLBOR’s customer service through email.
  2. Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents are missing, only sales return or chargeable service will be provided.
  3. If the COLBOR product is out of warranty coverage, the service and the cost of the parts will be charged.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

WARRANTY CERTIFICATE


Please register your warranty. Meanwhile, you are welcome to contact us via Email.
USER INFORMATION| Customer Name:
Phone Number:
Email:
Address:
SALES INFORMATION| Sales Date:
Model:
Product Code:
Dealer:
REPAIR RECORD| Service Date:
Technician:
Issue:

RESULT  ❑ Solved ❑ Unsolved – Retumed(Replaced)

Guangzhou Zhiying Technology Co., Ltd
Block 15th, No.200 Fangcun Avenue East, Liwan District, Guangzhou, China, 510000
support@colborlight.com
www.colborlight.com
2021/4/30 18:08:57

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals