COLBOR CL60R RGB COB Video Light User Manual
- June 10, 2024
- COLBOR
Table of Contents
User Manual CL60R RGB COB Video Light
Thank you for choosing COLBOR product. Please read this manual carefully before use and f o l l o w all instructions mentioned herein.
Safety Instructions
- Please read and fully understand this manual before using the product.
- Please remove the COB protective film to avoid damage by overheat before first use.
- Please remove the COB protective cover to avoid damage by overheat before every use.
- Do not use the product under moist environment or with wet hands. Do not allow the product to be splashed or soaked in water.
- Keep the product away from corrosive chemicals and liquid to avoid damage.
- Keep the product out of children’s reach during use. Do not leave the product unattended.
- When the product is working, the COB and heat sink will produce high temperature. Do not block, turn upside down and touch with hands.
- To ensure the service life, the cooling system still runs for a while after shutdown until the COB is below 45C .
- Please disconnect the power supply and put away the power cord when it is not in use.
- During use, arrange the power cord in order to avoid tripping and cutting off the power or damaging the product.
- Let the product cool completely before storage. Remove the power cable from the product and put it in the corresponding position of carrying bag after cooling down.
- Do not disassemble the product by yourself, otherwise the warranty will be invalid. If any fault occurs, please refer it to an authorized technician for inspection or maintenance.
- Recommend to use the original parts of COLBOR. If the product is damaged due to the use of the non-original parts, it is not included in the warranty of our products.
- Drop or external impact may cause product failure. Artificial damage is not covered by warranty.
- COLBOR reserves the right of final interpretation of the products. The product design and specifications are subject to change without notice.
Product Instructions
- COB Bead
- Bead Radiator (Air Outlet)
- Bowen Mount Adapter (BAR1)
- Ejector Pin
- Rail
- Air Vent (Air Intake)
- Quick-mount Holder (EC Stand)
- LCD Display Screen
- Up Control Wheel
- Down Control Wheel
- Setting (SET) Button
- Light Effect Frequency (RATE) Button
- Light Effect Mode (EFF) Button
- Light Mode MODE) Button
- Type—C Power Input
- Power Button
- Color Indicator bar
Installation & Disassembly
-
Remove COB protective cover
Hold the COB protective cover and pull it out as the arrow shows.
Note: Make sure remove the cover before every use to avoid heat damage. -
Install adapter and reflector
Align the inner frame of adapter ring with the outer frame of light, and push the adapter ring into the light from the head. Fasten two marbles on the adapter ing to the chute.
When disassembling, push the adapter ring towards the head of the lights Align the reflector with the adapter ring and insert It. The ejector pin is inched by reflector. Rotate the reflector tightly clockwise and the ejector pin springs back.
When disassembling, push the ejector pin and rotate the reflector anticlockwise. -
Fixing of the video light
Slide the quick—-mount holder into the chute under the light and rotate the knob a tightly.
Install tripod into the quick-mount holder and rotate the knob b tightly.
Adjust the light to the desired angle and rotate the knob c tightly. -
Multi-light connection & disassembly
Slide the rail of one lighting to the chute of the other until the pins inlay.
When disconnecting, slide the light out of the chute. -
Install VM2
Slide VM2 in to the chute of light, determine the fixed position and adjust the lever to lock.
When removing, adjust the level to unlock and slide out of the light. -
Power supply
Fixing power cables
Screw the power cable fixing clip, put the cable in to the groove, and then align the bracket with the tightening screw. DC power supply
Connect power adapter with Type—C power input and turn on.
Battery power supply
Turn on power after installing V-mount and battery.
Power adapter (PAQQ) and V – port battery power cable (VC50) are only for powering CL60, CL60M and CLE6OR, not for other electronic devices. If any damage caused by the wrong use, it is not within our warranty.
Operation Instructions
- Before using the product for the first time, please be sure to tear off the protective film in front of the COB bead.
- Power On: connect the power cord with the power adapter, plug the connector of adapter into the fixture’s power input, then attach to an electricity supply.
- Function: long press the power button, then the power button lights up. The product enters operation interface. (Factory default mode: CCT)
- Power Off: press the power button.
Status Icon Description
APP Connection Status Icon
| After selecting wireless connection in Settings menu, the icon will be
displayed dynamically.
| The icon is always on to indicate successful pairing with mobile APP.
The icon disappears to indicate mobile APP pairing failure, or the product is
unpaired.
Fan Status Icon
| Smart Mode. The product will adjust the fan speed according to the internal
detected temperature to ensure that it is in optimal working condition.
| Quiet Mode. The fan keeps running at low speed for minimum noise, and
overheating protection will be activated if the product temperature is higher
than the alarm value.
Group Status Icon
| None grouping status. The product defaults to the factory status, and will
not be affected by other groups.
| A stands for Group A. There are 15 groups (A-0). T stands for Tx.
| A stands for Group A. There are 15 groups (A-0). R stands for Rx.
| A stands for Group A. There are 15 groups (A-0). TR stands for TxRx.
Repeater Status Icon
| If the icon is always on, it means that Repeater function is turned on, and
if the icon disappears, it means the function is turned off.
Product Overheated Alarm Icon
| If the icon flashes, it means that the internal temperature of the product
is too high, and cooling measures need to be taken. If the icon disappears, it
means that the operation is normal.
CCT Mode (Short press CCT Mode Button to enter)
When adjusting parameters, the screen will enlarge the value of the current setting parameters, and it will automatically return to the main screen after 1.5 seconds without any operation.
HSI MODE ( Short press MODE button to switch CCT/HSI MODE)
When adjusting parameters, the screen will enlarge the value of the current
setting parameters, and it will automatically return to the main screen after
1.5 seconds without any operation.
EFF-CCT mode ( Short press the EFF mode button to enter EFF mode and
default EFF-CCT)
EFF-HSI mode (short press the EFF mode button, short press the up wheel to switch the EFF—-HSI mode)
| CCT Mode| CCT: 1000K-10000K
DIM: 0%-100%
Rate: Lv1-5
---|---|---
HSI Mode| Hue: 0° -359°
SAT: 0%-100%
INT: 0%-100%
Rate: Lv1-5
| CCT Mode| CCT: 1000K-10000K+RANDOM
Dim: 0%-100%+RANDOM Rate: Lv1-5+RANDOM
HSI Mode| Hue: 0° -359° +RANDOM
SAT: 0%-100%+RANDOM
INT: 0%-100%+RANDOM
Rate: Lv1-5+RANDOM
| CCT Mode| COT: Lock
Dim: 0%-100%+RANDOM Rate: Lv1-5
---|---|---
HSI Mode| Hue: Lock
SAT: 0%-100%+RANDOM INT: 0%-100%+RANDOM Rate: Lei -5
| CCT Mode| COT: 1000K-10000K Dim: 0%-100%
Rate: Lv1-5
HSI Mode| Hue: 0° -359° SAT: 0%-100% INT: 0%-100% Rate: Lei -5
| CCT Mode| Type: Red and white, blue and white, red and blue Dim: 0%-100%
Rate: Lei -5
| CCT Mode| COT: 1000K-10000K+RANDOM Dim: 0%-100%+RANDOM Rate: Lv1-5+RANDOM
HSI Mode| Hue: 0° -359° +RANDOM SAT: 0%-100%+RANDOM INT: 0%-100%+RANDOM Rate:
Lv1- +RANDOM
| CCT Mode| COT: 1000K-10000K+RANDOM Dim: 0%-100%+RANDOM Rate: Lock
HSI Mode| Hue: 0° -359° +RANDOM SAT: 0%-100%+RANDOM INT: 0%-100%+RANDOM Rate:
Lock
| CCT Mode| COT: 1000K-10000K Dim: 0%-100% Rate: Lv1-5
HSI Mode| Hue: 0° -359° SAT: 0%-100% INT: 0%-100% Rate: Let -5
| CCT Mode| COT: 1000K-10000K Dim: 0%-100% Rate: Lei -5
HSI Mode| Hue: 0° -359° SAT: 0%-100% INT: 0%-100% Rate: Let -5
| CCT Mode| COT: 1000K-10000K Dim: 0%-100% Rate: Let -5
HSI Mode| Hue: 0° -359° SAT: 0%-100% INT: 0%-100% Rate: Lel -5
| CCT CT: 1000K-10000K+RANDOM
Mode Dim: 0%-100%+RANDOM
Rate: Lv1-5
---|---
Hue: 0° -359° +RANDOM
HSI SAT: 0%-100%+RANDOM
Mode INT: 0%-100%+RANDOM
Rate: Lv1-5
| CCT Mode| CCT: 1000K-10000K Dim: 0%-100% Rate: Lv1-5
HSI Mode| Hue: 0° -359° SAT: 0%-100% INT: 0%-100% Rate: Lv1-5
| CCT Mode| CCT: 1000K-10000K Dim: 0%-100% Rate: Lock
HSI Mode| Hue: 0° -359° SAT: 0%-100% INT: 0%-100% Rate: Lock
Settings
- Short press Settings Button to enter settings menu.
- Roll the Brightness Control Wheel to choose setting.
- Roll the Color Temperature Control Wheel to adjust corresponding setting (Wireless connection adjust need short press).
When Group function is on, if the product is operated after a period of time,
it takes time to connect between products, so there will be millisecond delay.
The effective distance of transmitter(TX), receiver (RX), transmitter &
receiver (TXRX) is 10 meters.
Repeater (RP) function is the auxiliary function to enhance the signal of
light control and the effective distance of light control. However, too many
uses of RP function can affect product response time due to environmental
factors.
If the distance between lights in a group is more than 10 meter, it is
recommended to set a light in the middle as a signal RP point to increase the
control distance. In addition, in the state of multi-light connection, the
response of the product can be effectively improved when the RP function of
one light is turned on if connected lights are more than five, the RP function
of two lights are turned on if there are more than ten, and so on.
Restore factory settings: long press two wheels together for 5 seconds and the
product reboots to restore the factory default mode.
Specifications
Color Rendering Index | 97+ |
---|---|
Beam Angle | , L 12W Reflector ,Z 15° |
Lighting Range | Full Color |
Color Temperature Range | 2700K-6500K(±200) |
Illumination | See the Form Below |
COB Output Power | > 60W |
Rated Power | 80W (Max Power) |
Light Working Voltage | DC 20V 4A |
Cooling Mode | SMART/QUIET |
Connector | Type-C, supports PD3.0 20V 4A |
Body Material | Aluminum Alloy-FABS |
Light Dimension (mm) | 140.80*90 (Light Base Not Included) |
Weight | Light: 600g Light Base: 160g |
Operating Environment Temperature | -10-50°C |
Packaging List
The power adapter will vary according to different regions.
About Product
-
After the test, the product with assembly structure has bearing capacity of Akg. Customers need t o use according to actual conditions.
-
It is recommended to use the original power adapter for power supply.
The malfunction will not be included in the warranty if use other equipment to power the product. -
When more than five lights are assembled into a light matrix, taming on the RP function in one of them to provide better control stability. If the number of lights reaches 10, enable the RP function for two of them, and so on.
More functions of COLBOR
https://www.colborlight.com/pages/colbor-apps-download
Scan the above QR code to the webpage and download the relevant apps, so that you can be benefit with more functions such as remote light control and firmware upgrade.
WARRANTY
Warranty Period
Thank you for purchasing COLBOR products.
- Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
- Original COLBOR products are entitled to 12-month limited warranty service.
The warranty period begins on the date of purchase of brand new, unused products by the first end-user. Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations
- Faults resulted from inappropriate use of a product without following its operation specification
- Artificial damage, e.g. crash, squeeze, scratch, soaking, exposing to rain or damp
- Modifications to a product by its user or a third party without prior written consent of COLBOR, e.g. replacement of element or circuit, label alteration
- The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off
- All consumable accessory attached to a product, like cable, cover
- Faults as a result of force majeure, such as fire, flood, lightning, etc.
Warranty Claim Procedure
- If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact COLBOR’s customer service through email.
- Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided.
- If the COLBOR product is out of the warranty coverage, the service and the parts cost will be charged.
Form 1
Illumination
CCT | 0.5m | 1 m | 3m |
---|---|---|---|
Light Base 2700K | LUX | 5336 | 1415 |
FC | 496 | 131 | 23 |
Reflector | LUX | 53015 | 17135 |
FC | 4934 | 1599 | 181 |
Light Base 3200K | LUX | 6038 | 1587 |
FC | 561 | 147 | 25 |
Reflector | LUX | 60375 | 19550 |
FC | 5612 | 1817 | 198 |
Light Base 4300K | LUX | 7418 | 1886 |
FC | 689 | 176 | 30 |
Reflector | LUX | 71300 | 22195 |
FC | 6624 | 2070 | 227 |
Light Base 5600K | LUX | 7993 | 2082 |
FC | 743 | 193 | 32 |
Reflector | LUX | 75900 | 22655 |
FC | 7050 | 2105 | 229 |
Light Base 6500K | LUX | 8390 | 2217 |
FC | 781 | 205 | 33 |
Reflector | LUX | 79084 | 22974 |
FC | 7344 | 2129 | 230 |
Light Base R | LUX | 1541 | 442 |
FC | 144 | 41 | 8 |
Reflector | LUX | 8556 | 1530 |
FC | 796 | 141 | 19 |
Light Base G | LUX | 4393 | 1150 |
FC | 408 | 107 | 18 |
Reflector | LUX | 23345 | 4336 |
FC | 2174 | 403 | 41 |
Light Base B | LUX | 788 | 223 |
FC | 73 | 21 | 4 |
Reflector | LUX | 4658 | 1010 |
FC | 432 | 94 | 11 |
The data is given from testing in a laboratory.
WARRANTY CERTIFICATE
Please register your warranty. Meanwhile, you are welcomed to contact u s
via Email.
USER INFORMATION | Customer Name: |
---|
Phone Number:
Email:
Address:
SALES INFORMATION| Sales Date:
Model:
Product Code:
Dealer:
REPAIR RECORD| Service Date:
Technician:
Issue:
RESULT Solved Unsolved Retimed (Replaced)
Guangzhou Ziyang Technology Co., Ltd
Room 2401, 24 / F, South Tower, Lashing Plaza, No. 6 8 Hundi Avenue, Liwa
District,
Guangzhou, China, 510000
suppor@colborlight.com
www.colborlight.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>