EDIFIER X3s True Wireless Stereo Earbuds Instruction Manual

: June 6, 2024
: Edifier

Table of Contents

Operating instructions
FAQs
Maintenance
FCC statement:
- FCC Regulatory Compliance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

X3s
True Wireless Stereo Earbuds

For user safety and compliances, also for optimum performance, please carefully read safety instructions and use the product in accordance with them.

Product description and accessories

Note:

There are different sizes of ear tips attached in the package, please select the suitable ones to wear.
Images are for illustrative purposes only and may differ from the actual product.

Operating instructions

Charge

Charge the earbuds
• You may hear a warning tone with the red light flashing when the earbuds are at the low battery level, please place the earbuds in the charging case for charging.
• Red light of the earbuds steady lit = charging
The red light of the earbuds off = fully charged
Charge the charging case
• Please connect the charging case to the power source with the included Type-C charging cable for charging.
• Red light on the case steady lit = charging Red light on the case off = fully charged
Input: 5V 200mA (earbuds)
5V 1A (charging case)

Warning:

The rechargeable batteries that provide power for this product must be disposed of properly for recycling. Do not dispose of batteries in a fire to prevent an explosion.
The power source used must be approved by relative departments and in accordance with electronic specifications of devices as well as local regulatory requirements (e.g. UL, CSA, VDE, CCC), otherwise, there may be dangers of fire, explosion, etc.

Power on/off

The earbuds will power on when taken out of the case.
The earbuds will power off when placed in the case.

Bluetooth connection

For initial use, the earbuds will auto-enter Bluetooth pairing mode when taken out of the charging case;
Bluetooth pairing mode: red and blue lights flash rapidly
connect to another mobile phone: Please take out the earbuds, and press and hold the touch button of the left or right earbud for around 2-3 seconds to enter Bluetooth
pairing mode.
Set the mobile phone to search for and connect to “EDIFIER X3s”, after pairing is successful, the blue light will flash slowly.

TWS connection of the left and right earbuds

The left and right earbuds have finished TWS pairing before leaving the factory. If the wireless connection fails to resume, please follow the steps below to re-pair:

When the earbuds are in the charging case, respectively and quickly triple-click the touch buttons of the left and right earbuds until the blue lights flash rapidly, then the earbuds enter the TWS pairing mode of the left and right earbuds;
After pairing is done, the red lights on the left and right earbuds will be steadily lit.

Clear pairing records

When the left and right earbuds are interconnected and not connected to any Bluetooth devices, please take out the earbuds, and quickly triple-click the touch button of the left or right earbud until the blue light flashes rapidly, then the pairing records of both earbuds will be cleared.

Functional operation

Music playback mode (Bluetooth already connected and you are not in a conversation)

Call mode (Bluetooth already connected, and there is an incoming call or you are in a conversation)

FAQs

When charging the charging case, the indicator is off.

Please ensure the charging case is correctly connected with the power source.

No sound

Check if the earbuds are operating.
Check if the earbud’s volume is at an appropriate level.
Check if the earbuds are correctly connected to a mobile phone.
Check if the earbuds are operating within a normal working range.

The call quality of the earbuds is not good.

Check if the mobile phone is in an area with a strong signal.
Please ensure the earbuds are within an effective distance (10m) and no obstacles between the earbuds and mobile phones.

When playing music, cannot control pause/play/previous track/next track via the earbuds.

Please ensure the paired device support AVRCP (Audio/Video Remote Control Profile) profile.

Maintenance

If it is not used for long periods of time, please charge the product with a lithium battery every three months.
Keep the product away from humid places to avoid affecting the internal circuit. Do not use the product during
intense exercise or with much sweat to prevent sweat from dropping into the product to make damage.
Do not put the product in places exposed to the sun or with high temperatures. The high temperature will shorten the service life of electronic components, damage batteries, and make plastic components deformed.
Do not put the product in cold places to avoid damaging the internal circuit board.
Do not dismantle the product. Non-professional personnel may damage the product.
Do not drop, strongly vibrate, strike the product with a hard object to avoid damaging the internal circuit.
Do not use drastic chemicals or cleaner to clean the product.
Do not use sharp objects to scratch the product surface to avoid damaging the shell and affecting the facade.

FCC statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IC statement: CAN ICES-3(B)/NMB-3(B).

FCC ID: Z9G-EDF150
IC: 10004A-EDF150

Declaration for EU
Frequency Band: 2.402GHz ~ 2.480GHz
RF Power Output: ≤20 dBm (EIRP)
There is no restriction of use.

FCC Regulatory Compliance

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Compliance
This equipment complies with FCC radiation exposure knits set forth for an uncontrolled environment

ISED Regulatory compliance

This device contains license-exempt transmitters that comply with Innovation. Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.

This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

Cet equipement est conforme aux limites d’exposition aux radiations IC CNR-102 etablies pour un environnement non controle.

Model: EDF200060
Edifier International Limited
P.O. Box 6264
General Post Office
Hong Kong

www.edifier.com
2021 Edifier International Limited. All rights reserved.
Printed in China

NOTICE:
For the need of technical improvement and system upgrade, the information contained herein may be subject to change from time to time without prior notice.
Products of EDIFIER will be customized for different applications. Pictures and illustrations shown on this manual may be slightly different from the actual product. If any difference is found, the actual product prevails.