SOUNDPEATS Halo Bluetooth Speaker V5.0 Portable Wireless Speaker User Guide

: June 6, 2024
: SoundPEATS

Table of Contents

Product Diagram
Pairing
Reset
Enter/Exit TWS Mode
Button Control
Charge
Q&A
Documents / Resources

Using Guide

Product Diagram

Pairing

Long press the MFB for 1.5s to turn on, the indicator starts to flash blue for 1s, then Bluetooth speaker enters pairing mode, the indicator flashes in blue and green alternately.
Activate Bluetooth on the device, and choose “SOUNDPEATS Halo” on Bluetooth list to pair.

Reset

Please plug the Type-C charging cable into the speaker, and make sure they are in charging status.
Under the power-on status, long press the Bluetooth button for 10s until the indicator flashes in green twice, reset complete.

Enter/Exit TWS Mode

Enter
Under the power-on state, long press the Bluetooth button for 3s, the speaker enters TWS mode, The indicator flashes blue quickly, and then it enters pairing mode and lasts for 3 minutes.
Note:
Under the power-on state, the speaker pairs to the phone at first is the master unit, In TWS mode, only the master speaker can hold the call.
Exit TWS Mode
Long press the Bluetooth button for 3s again to exit the TWS mode, it only works on the speaker being operated, then the speaker will return to pairing mode after exiting TWS mode.
Note:
After exiting TWS mode, only the main speaker can connect with the phone.

Button Control

Power On	Long press the MFB for 1.5s
Power Off	Long press the MFB for 3S
Play/Pause	Press the MFB once
Volume Down	Press the “-” once
Volume Up	Press the “+” once
Previous Track	Long press “+”for 1.5s
Next Track	Long press “-“for 1.5s
Answer/Hang Up Phone Call	Press the MFB once
Switch Between Two Active Calls	Long press the MFB for 2s
Discornect Bluetooth and Enter Paring Mode Manually	Press the “Bluetooth

button” in the power-on status
Activate/Close Voice Assistant| Press the “Voice assistant button” once
Activate/Close Ambient Light| Long press “Voice assistant button-for 3s while the speaker is on

Charge

Use a Type-C adapter to charge the speaker (current less than 1A). The LED flashes slowly in red while charging and goes off when fully charged.
Please charge the speaker at least once per 3 months when not in use for a long time.

Q&A

Ql: How to enter TWS mode?
The TWS mode requires 2 speakers to be used simultaneously. We recommend you to buy 2 speakers to have better music experience.

Q2: How long can the speaker play with a single charge?
The speakers can work continuously for 13 hours with a single charge. If you don’t use the speaker for a long time, please turn it off or deactivate your phone Bluetooth, the speaker will power off automatically after 3 minutes.

FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road, Longhua District, Snenzhen, China. 518109
support@soundpeatsaudio.com
www.soundpeatsaudio.com

Company: Qing UG(haftungsbeschrankt)
Address: Undinestr. 7, 12203 Berlin Germany

FCC ID: 2AFTU-DD020
MADE IN CHINA

Documents / Resources

| SOUNDPEATS Halo Bluetooth Speaker V5.0 Portable Wireless Speaker [pdf] User Guide
DD020, 2AFTU-DD020, 2AFTUDD020, Halo, Bluetooth Speaker V5.0 Portable Wireless Speaker, Halo Bluetooth Speaker V5.0 Portable Wireless Speaker
---|---
| SOUNDPEATS Halo Bluetooth Speaker V5.0 Portable Wireless [pdf] User Manual
Halo Bluetooth Speaker V5.0 Portable Wireless, Halo, Bluetooth Speaker V5.0 Portable Wireless, Portable Wireless